eChapters

Irrigation Methods

Surface

Sub-surface

Pressurized irrigation

12.1 Surface Irrigation

Surface irrigation method refers to the manner or plan of water application by gravity flow to the cultivated land wetting either the entire field (uncontrolled flooding) or part of the field (furrows, basins, border strips). Most irrigated areas have characteristic land features and differ from those in other areas. Hence, for efficient application of water it is important to select such method of irrigation, which fits one’s own land.

The adoption of a certain method need not be necessarily based on convention or that followed in the adjoining farm. The factors, which determine the suitable method of irrigation are local conditions (soil type - its permeability & water storage capacity; land topography, climate, water availability & water quality), crop type, type of technology, previous experience with irrigation, required labour inputs etc. Good yield of crops can be obtained from irrigated land only if the water is applied judiciously to meet the needs of the plant, but not to cause waste and damage. Irrigation water is applied to cultivated land by the following surface methods of irrigation:

It is the scholastic and theoretical exercise that configures the operational definition and text of entire research work. The conceptual inputs, axiomatic inputs, logic of discourses and the pursuit knowledge come together to frame the theory in compliance and in congruence with the set of objectives and research designs spelt out in the research process.

3.1 Definition of Farmer, Farm, and Farming System

A farmer is a person engaged in agriculture, raising living organisms for food or raw materials. The term usually applies to people who do some combination of raising field crops, orchards, vineyards, poultry, or other livestock. A farmer might own the farm land or might work as a laborer on land owned by others. In most developed economies, a “farmer” is usually a farm owner (landowner), while employees of the farm are known as farm workers (or farmhands). However, in other older definitions a farmer was a person who promotes or improves the growth of plants, land or crops or raises animals (as livestock or f ish) by labor and attention. Over half a billion farmers are smallholders, most of whom are in developing countries, and who economically support almost two billion people. Globally, women constitute more than 40% of agricultural employees.

A farm is an area of land where livestock (animals) are raised and crops (plants) are grown for use as food, fiber, and fuel. The people who own and work on the farm are called farmers.

Introduction

In almost all biological studies, it will be impossible to account for every individual in a population. Therefore, it is necessary to examine a sub-group of the total population and extrapolate from this to the whole population. The process by which the sub-group of the population is selected is sampling. Nearly, all statistical tests make a fundamental assumption that sampling of individual will be at random from all the individuals that could possibly be sampled. It is very important that timing is taken into account either by sampling strategy or by later analysis. Most population will be affected by season, time of day and local weather conditions.

What is considered here is the problem faced by an ecologist working in the field and trying to design a suitable sampling strategy. The use of the very powerful statistical technique; analysis of variance (ANOVA) is more common in the situation of a controlled experiment, where, we are analyzing the effects of different levels of a treatment (e.g. feed, fertilizer, temperature etc.) on some measured aspect of population, Then, to get a true estimate of the effect of the treatment, experimental design will be of paramount importance.

The State of Himachal Pradesh encompasses a geographical area of 55.7 lakh ha and is situated between 31°22’40" and 33°12’40"N latitude and 75°45’55" and 77°10’20"E longitude. The state is bordered by Jammu and Kashmir on the north, Punjab on the west, and Haryana on the south-west (Fig. 19.1). About 12 per cent of the state area is under agriculture which is mostly (80 per cent) rain fed. Wheat, maize, rice, and barley are the principal crops. In state, there are 12 districts, viz., Bilaspur, Chamba, Hamirpur, Kangra, Kinnaur, Kullu, Lahaul & Spiti, Mandi, Shimla, Solan, Sirmaur and Una. About 20 per cent of the area is under forest cover. It is rich in biodiversity of flora and fauna. Nearly 27 per cent of the area of the state is covered under permanent pastures. The state is endowed with a wide range of physiography/landform, climate, vegetation and geology which have influence on genesis of soils. The soils are mostly shallow, medium deep to deep, well/excessively drained, sandy, sandy-skeletal, loamy-skeletal, coarse-loamy and fine-loamy, calcareous as well as non-calcareous with low available water capacity. The State is the biggest montane ecosystem in India situated in northern part of the country. It is seventeenth largest state in terms of area and twentieth in population of which 65 per cent people are dependent on agriculture and 60 per cent of GDP comes from agriculture sector. Increasing temperature and reducing rainfall affecting the crop growth and crop production is a major issue everywhere in the world nowadays and this state has also not remained untouched by these prime issues of climate change. For sustainable development of agriculture in state, there was/is a need to identify and quantify climatic change where agriculture has a significant influence on both the economy and livelihood.

Abstract

Increasing global demand for ‘fresh-like’ processed food products has forced food industries to investigate into various minimal processing techniques. Food processing in general has been associated with thermal processing, alone or in various combination with chemical and mechanical preservation and processing methods. However, thermal processing methods are energy intensive in nature and tend to reduce product quality and freshness at the cost of shelf-life gain. Advance technique such as microwave, radio-frequency and freeze drying do maintain the product quality but their implementation at industrial scale involves high operational and maintenance cost. An ideal processing method therefore would be one that can process food products without losing its quality, is energy efficient and is easily scalable. In this chapter, we discuss about ‘Electrohydrodynamic (EHD) Drying’, which is can be classified as a minimal processing technique. The heat and mass transfer principles involved in EHD drying have been extensively discussed and so has been the key consideration for designing an EHD drying system.

INTRODUCTION TO FINANCIAL MANAGEMENT

CONCEPT AND DEFINITION OF FINANCIAL MANAGEMENT: Financial management is an integral part of general overall management. The term ‘Financial management’ is managerial activity that is concerned with planning and controlling of financial resources of a firm. Financial management is concerned with managerial decisions that result in the acquisition and financing of long and short-term credits of the farm or any enterprise. Financial management is concerned with the efficient use of all important economic resources that is capital funds of a firm (Solomon Ezra)

Financial management is an application of general managerial principles to the era of financial decision-making. (Howard &Uptron).

Financial management is an area of financial decisions making, harmonizing individual motives and enterprise goals.(Weston & Brigham).

Financial management is an operational activity of a business that is responsible for obtaining and effective utilizing the funds necessary for efficient operations.(Joseph & Massie)

The history of Patent law in India starts from 1911 when the Indian Patents and Designs Act, 1911 was enacted. The present Patents Act, 1970 came into force in the year 1972, amending and consolidating the existing law relating to Patents in India. The Patents Act, 1970 was again amended by the Patents (Amendment) Act, 2005, wherein product patent was extended to all fields of technology including food, drugs, chemicals and micro organisms. After the amendment, the provisions relating to Exclusive Marketing Rights (EMRs) have been repealed, and a provision for enabling grant of compulsory license has been introduced.

1. Introduction

Education is undergoing a digital transformation. The incorporation of digital technologies into the educational scene over the last two decades has radically changed the way we teach and learn. This transition has started a revolution with far-reaching repercussions, both positive and negative, for students, educators, and institutions alike.

The growing adoption of digital technologies in educational settings has created a world of possibilities. Online platforms, learning management systems, educational apps, virtual reality, and augmented reality are just a handful of the innovations that have transformed the educational experience. This comprehensive investigation tries to investigate the intricate and multifaceted impact of various digital technologies on schooling.

1. Introduction
Plastic pollution is a global problem that requires immediate attention due toits negative impacts on ecosystems, infrastructure, (MacLeod, M., Arp et al.2021) society, and the economy (Honingh, D. et al.,2020).In terms of absolute emissions, we find that South-eastern part of Asia, andSub-Saharan part of Africa possess the greatest quantities of plastic pollution,with India emitting the most (9.3 Mt year−1), or about one-fifth of the world'stotal plastic pollution (Joshua W. Cottom et al.).
Future regulations pertaining to the manufacturer, usage, and getting ridof plastics will be influenced by the discussions for a worldwide plasticpollution treaty. A baseline with great resolution of waste flows and sourcesof plastic emissions will be useful for the stakeholders in order to identify
pollution hotspots and the reasons behind them (United Nations EnvironmentProgramme). Furthermore, in addition to the production of municipal waste,the pandemic of coronavirus illness has raised the usage of disposable polymerproducts, masks, tissues, gloves, and additional personal protection equipment,which made the plastic pollution disaster worse (De-la-Torre GE et al., 2021).Wasted plastics can break down and fragment into three different sizes: 1mm to 5 mm big microplastics, 1 μm to 1 mm microplastics, and 1 nm to1 μm nano plastics, (Waller et al., 2017; De-la-Torre 2020; Atugoda et al.,
2022) being exposed to ultraviolet (UV) light and other processes that causeenvironmental damage

1.1. Mushroom

Fruiting body of fungus appears above ground and contains spores.

Fungi are network of fine microscopic threads collectively known as mycelium.

Fungi are the part of the plant kingdom and don’t contain chlorophyll and root system.

Mushroom comes under sub division Basidiomycotina, order – Agaricales.

Introduction

Agriculture is the backbone of Indian economy. There are a number of sub sectors in the agricultural sector such as sericulture, floriculture and horticulture. Among those fields horticulture has played a dominant role in the total agricultural output throughout India. The world market has provided a good opportunity for the development of the fresh and the processed fruits industry of India. From the point of view of domestic market also, horticulture products have provided food items of nutritional value. Their cultivation has generated higher employment opportunities and higher returns to the farmers than the cereals and other agricultural cash crops (Singhal, 1995). Mango (Mangifera indica) is a stone fruit belonging to family Anacardiaceae. It is a most important fruit of India and known as the “king of tropical fruits”. Mango is cultivated in many tropical regions and distributed widely in the world. 

Cocoa is popularly known as cacao in many cocoa growing nations. Cocoa beans are the source of commercial cocoa. The cocoa products viz., cocoa liquor, cocoa butter, cocoa cake, cocoa powder and cocoa chocolate are widely consumed across the World. Cocoa powder is essentially used as flavour in biscuits, ice cream, dairy drinks and cakes. Apart its use as flavour it is also used in the manufacture of coatings for confectioners or frozen desserts. Cocoa powder is also consumed by the beverage industry for example for the preparation of chocolate milk. Besides the traditional uses in chocolate manufacture and confectionery, cocoa butter is also used in the manufacture of tobacco products, soap and cosmetics. It is also a folk remedy for burns, cough, dry lips, fever, malaria, rheumatism, snakebite and wounds. It is reported to be antiseptic and diuretic. Looking at the industry needs for various purposes, there is a heavy demand for cocoa. At present, the gap between supply and demand in cocoa appears to be more at the national level. To fill the gap, various agro-technologies and crop improvement strategies are to be chalked out, for which the response of the crop to various environmental factors are to be understood. Weather aberrations during the flowering and fruiting result in the final cocoa production. Therefore, it is important to understand the effect of weather on flowering and fruiting pattern of cocoa to minimize the crop losses against the weather abnormalities. Though it is known that cocoa yield is highly variable and sensitive to various weather factors, the studies on crop weather relationships in cocoa and its response to climate change/variability are relatively scant

Cattleya belongs to the family Orchidaceae. It is highly important in floriculture and has been cultivated since the 19^th century. The name “Cattleya” was given in the honour of “Sir William Cattley”. Cattleyas have earned the reputation as the “Queen of Orchids” and are known to the public as the ultimate in floral corsages. While no longer the reigning queen of the orchid floral industry it is difficult not to be impressed by a well-flowered Cattleya. No longer limited to white and various shades of lavender and purple, high quality flowers occur in all colours except true blue and black and in a wide range of plant sizes. They are widely known for their large, showy flowers and were used extensively in hybridization for the cut-flower trade until the 1980s when pot plants became more popular.

Small cardamom (Elettaria cardamomum Maton), popularly known as the “Queen of spices”, occupies an important position among the foreign exchange earning commodities. It is cultivated on a commercial scale in Sri
Lanka, Guatemala, Tanzania and Papua New Guinea. Guatemala is the largest producer of cardamom in the World. In India, it is confined to the States of Kerala, Karnataka and Tamil Nadu. Among these States, Kerala
accounts for the major portion of production (58.4 %), followed by Karnataka (35.2 %) and Tamil Nadu (6.4 %). In Kerala, Cardamom is mainly grown in the erstwhile Travancore area in Idukki district and it is known as the Cardamom Hill Reserve (CHR). Cardamom is a native of the moist evergreen rain forests of the Western Ghats and is grown extensively in the hilly regions at elevations of 700 to 1300 metres as an under crop in forest lands. Cardamom thrives well within certain maximum and minimum thermal regimes. It is believed that diurnal symmetries in temperature trends, if any, have close links with the changes in cloudiness, humidity, atmospheric circulation pattern, winds and soil moisture. The land use pattern of cardamom tracts has changed to a great extent in recent decades. Crops like coffee, black pepper and areca nut are being cultivated at many locations in place of cardamom. With denudation of forests in many cardamom areas, the ideal cool humid microclimate has been destabilized and adversely affected the productivity of the crop.

Cucumber (Cucumis sativus var. sativus L., 2x = 2n = 14, normally monoecious, cross-pollinated) is a member of the economically important family Cucurbitaceae which includes squash/pumpkin (Cucurbita ssp.), watermelon [Citrullus lanatus (Thunb.) Matsum. & Nakai], melon (Cucumis melo L.) and gourds. After tomato (Solanum lycopersicum L.) and watermelon, cucumber and melon are cultivated more widely than any other vegetable species globally accounting for about 2.5 million ha and producing 43 million tons giving a productivity of over 17 tons/ha under field and greenhouse culture. Production of cucumber is the second largest of all cucurbits, where China, Iran, Russia, Turkey and the United States represent about 75% of the world production.

During 2017-18, India produced 1.25 million tons of cucumber from 0.08 million ha (80, 000) area resulting into a productivity of close to 16 tons/ha (MAFW, 2018). Top ten cucumber producing states in India in the same period are Haryana (17000 ha), MP (9500 ha), Karnataka (8300 ha), Assam (6900 ha), Maharashtra (4500 ha), Andhra Pradesh (4400 ha), Bihar (3900 ha), Punjab (3600 ha), Kerala (3400 ha) and UP (3300 ha).

Basic knowledge of statistics is important to understand animal breeding analysis. In this chapter, the hypothesis testing, principles of experimental design, types of data and probability distribution are described with examples using appropriate software.

Arabica coffee is reported to have originated in the tropical rain forests in Ethiopian highlands while Robusta is a native of the humid tropical lowlands of Central Africa, probably, Uganda. The major coffee producing countries
across the World are distributed between 23°N and 23°S of the equator. Beyond these latitudinal limits, temperature becomes a major limiting factor as coffee plants are sensitive to extreme temperature regimes. Thus within
the latitudes, altitude becomes a major factor. In areas, nearer to the equator, coffee plants require higher altitudes when compared to farther north and south (6.1 plate). The world’s largest coffee producer is Brazil with around 30% of total world output of coffee. Columbia comes in second with around two thirds of Brazil’s production. India is the sixth largest (after Brazil, Columbia, Vietnam, Indonesia and Ethiopia) producer of coffee. Coffee is reportedly introduced into the Western Ghats regions of South India around 1600 AD. However, commercial cultivation of coffee was opened in South India with the British enterprise and investment during late 1820s. Coffee occupies an important position among the plantation crops in India. It is cultivated mainly in the traditional States of Karnataka, Kerala, Tamil Nadu and to some extent in non-traditional areas viz., Andhra Pradesh and Orissa as well as in North Eastern States viz., Assam, Manipur, Meghalaya, Mizoram, Tripura, Nagaland and Arunachal Pradesh. Coffee in India is unique. Almost all coffee plantation are grown under the shade of forest/planted trees, where as it is grown under open conditions in all the major producing countries viz., Brazil, Vietnam and Columbia.

Introduction

In a technology that consistently maintains a fantastic development curve with capabilities doubling up year-to-year, freezing the hardware specification is not easy or very meaningful. GIS (not geography) owes to its genesis and progress to the developments in information technology front. It may be asserted that any and all upgrade in the hardware industry will only add to its own ability to effectively process more and more data and handle more complex routines. The personal computers of today are seen to be adequate to run typical GIS software. A reference hardware specification is discussed here. GIS software development is an involved process but then the software developers have made good use of hardware capabilities available and have released upgrades consistently. Hardware developments are such that they defy a static spcification. However a reference specification as on 2009. An overview of various software packages used in the past as well as present is attempted. ESRI released a new version in 2002 and claimed that their ArcGIS is an “integrated collection of GIS software products for building a complete GIS that enable users to deploy GIS functionality wherever it is needed, in desktops, servers, or custom applications; over the Web; or in the field.” The details are discussed below. While a number of software overviews are available, this text is not aimed at providing a tutorial to any of the software packages nor do the comparisons made are to promote any particular software. Similarly, it is presumed that the reader is familiar with the hardware elements and functionality. Lot of information about the software packages are available on their respective web sites and the reader is exhorted to look for current, additional and in depth information required in the pages. A brief discussion on Liveware or human resource can be found at the end of the chapter.

Impatiens balsamina (Balsam, Garden Balsam or Rose Balsam or Gulmehndi) is a species of Impatiens widely cultivated as an ornamental plant in landscaping belongs to the family Balsaminaceae. It is a qualitative short-day plant, propagated by seed and is one of the popular species of North India. It is called kamantigue in the Philippines. This species of Kamantigue are used in teas. In many English speaking countries they are known as “Touch me not”, possibly due to the ripe seed pods explosively bursting when touched. Different parts of the plant are used to treat disease and skin afflictions such as the leaves, seeds, and stems. It is also edible if cooked. Juice from balsam leaves treats warts and also snakebite, while the flower can be applied to burns to cool the skin. Impatiens balsamina L. has been used as indigenous medicine in Asia for the treatment of rheumatism, fractures, and fingernail inflammation. In Korean folk medicine Impatiens (‘Bong Seon Wha Dae’) has been used to cure constipation and acute gastritis by meat. There are mainly four forms of I. balsamina namely red, purples, white and pink.

ORIGIN AND DISTRIBUTION

Impatiens balsamina is a species of Impatiens native to southern Asia in India and Burma, but has been cultivated widely. It is now naturalized in many tropical and temperate areas of the world. Jones and Smith in 1966 proposed the Himalayan region as the centre of origin. The major centres of diversity are in highlands and mountains of tropical and sub-tropical Africa, Southeast Asia and the Indian sub-continent. In the U.S., Impatiens balsamina is found primarily in a wide strip encompassing the Northeast and Southeast regions from Florida to New York with specimens being found as far west as Missouri. Impatiens denisonii is a scapigerous herb which is found only in the Western Ghats in South India and are endemic in the Nilgiri Hills. Impatiens ecornuta, the spurless touch-me-not or western touch-me-not, is an annual flowering plant native to the northwestern United States and British Columbia in Canada. Impatiens flaccida is native to the Western Ghats in India and to Sri Lanka whereas, Impatiens hawkeri (New Guinea impatiens) is native to Papua New Guinea and the Solomon Islands. It has been bred and hybridized in cultivation to produce a line of garden plants. The species has been crossed with Impatiens aurantiaca and I. platypetala to improve characteristics such as drought-resistance. Impatiens irvingii is native to tropical Africa. Impatiens namchabarwensis (Blue Diamond Impatiens) is a 40–50 cm tall perennial plant, native to the Himalaya overwintering by a thick fleshy rootstock. Impatiens psittacina, known variously as the “parrot flower” or “parrot balsam” is a species of balsam from Southeast Asia that was described by the botanist Joseph Dalton Hooker and was noted for its flower that resemble a “flying cockatoo”. It is known from Thailand, Burma and parts of India (Morgan, 2007). Impatiens sodenii is native to Kenya and Tanzania. It is widely cultivated as an ornamental plant. I. walleriana is native to East Africa and yielded ‘Elfin’ series of cultivars, which was subsequently improved as the Super Elfin series.