eChapters

17.1 Introduction

It is well known fact that planners as well as end users have to consider any resources as technology from economic point of view. Therefore, it is important to have techno – economic analysis of each energy source option. In the feasibility study of particular energy option, three tier judgment approaches is required, which include technical feasibility, economical viability and social acceptability. Hence in the rural energy planning programme one has to considered techno socio economic analysis of an individual energy option. Since in integrated rural energy planning, locally available energy resources are used, presuming that it is socially recognized. Hence in the IREP project, the need and scope of techno economic analysis in terms of economic analysis of different technical feasible options, before between “economic” and “finical” analysis should be kept in mind. An economic analysis is needed to verify that a particular energy source will provide “net benefit” to society as a whole, before its final integration in the energy context, while a financial analysis integrated in the energy practices. In simple words, a financial analysis is concerned with goods and services, money inflow and outflows and the transfer of payments. An economic analysis also considers the social benefits and costs of goods and services which are not traded in a market.

16.1 Fuel Cell

Fuel cell is an electrochemical device that convert chemical energy of a reaction directly into electrical energy. The basic physical structure of a fuel cell consists of an electrolyte layer in contact with a porous anode and cathode on either side. A schematic representation of a fuel cell with the reactant or product gases and the ion conduction flow directions through the cell is shown in Fig. 16.1

15.1 Introduction

The oceans cover 71% of the earth’s surface and it acts a natural collector and store of solar energy. On an average day, 60 million sq. km. of tropical seas absorb an amount of solar radiation equivalent in heat content to about 245 billion barrels of oil, if this energy could be trapped, large scale renewable source becomes available especially for tropical countries. The energy available in the ocean is clean, continuous throughout the year and renewable.

Renewable energy contribution to the available energy resources is very important to the country as it is presently facing an energy resources crunch. Out of the total installed capacity of approximately 370.106 GW as on March 2020, Renewable Power Plants including hydro-electric plant contribute 35.86 % of total installed capacity. However, with the present increase in demand, more attention is required to extract the renewable sources so that at least 50 to 60 % share for the total energy requirement by the renewable energy sources.

There are various forms of ocean energy such as Ocean Thermal Energy Conversion (OTEC), Wave Energy, Tidal Energy, Salinity Gradient Energy, Offshore Wind Energy, Marine Currents, Marine Biomass Conversion. Among these, the first three forms are likely to be technically viable for the future.

More recently Ministry of New and Renewable Energy (MNRE), Government of India hasdeclared Ocean Energy as renewable energy, and clarified to all the stakeholders that energy produced using various forms of ocean energy such as tidal, wave, ocean thermal energy conversion among others shall be considered as renewable energy.

MNRE reported that, the total identified potential of tidal energy is about 8000 - 9000 MW, with about 7000 MW in the Gulf of Cambay in Gujarat, about 1200 MW in Gulf of Kutch and less than 100 MW in Sundarbans. Primary estimates of wave energy potential along Indian coast are about 5 – 15 MW/m, so that theoretical estimates are around 40 – 60 GW. Ocean Thermal Energy Conversion (OTEC) has a theoretical potential of 180,000 MW in India subject to suitable technological evolution. As of date, there is not any installed Ocean Energy capacity in India.

14.1 Introduction

Hydro-electric power is electricity produced by the movement of fresh water from rivers and lakes. Gravity causes water to flow downwards and this downward motion of water contains kinetic energy, that can be converted into mechanical energy, and then from mechanical energy into electrical energy in hydro-electric power stations. (“Hydro” comes from the Greek word hydra, meaning water). At a good site hydro-electricity can generate very cost-effective electricity.

13.1 Introduction

Geothermal energy is the nature-based heat generated from within the earth. Underneath the earth’s relatively thin crust, temperature range from 1000 to 4000°C & in some areas, pressures exceed 138 MPa is available. Geothermal energy is most likely generated from radioactive thorium, potassium and uranium dispersed evenly throughout the earth’s interior which produce heat as part of the decaying process. This process generates enough heating, keep the core of the earth at temperature approaching 400°C. Composed primarily of molten nickel & iron, the core is thought to be surrounded by a layer of molten rock, the mantle at approximately 100°C. Nine major crustal plates float on the mantle & currents in the mantle cause the plates to drift, colliding in some areas and diverting in others. When two continental plates converge a complex series of chemicals in the form of molten magna rises in the earth’s crust and depending upon its magnitude, it may break the crust and reach at the earth surface. Volcano, hot spring, geysers & fumaroles are natural geothermal resources near the surface and perhaps where economic drilling operations can tap their heat and pressure.

12.1 General

The term “biomass” generally refers to renewable organic matter generated by plants through photosynthesis. Materials having organic combustible matter is also referred under biomass. Biomass is an important fuel source in our overall energy scenario. Biomass is produced through chemical storage of solar energy in plants and other organic matter as a result of photosynthesis. During this process conversion of solar energy in sugar and starch, which are energy rich compounds takes place. The chemical reaction of photosynthesis can be written as:

6CO₂ + 6H₂ O + sun light → C₆ H₁₂ O₆ + 6O₂ + 636_kcal

It indicates that the storage of 636 kcal is associated with the transfer of 72 gm carbon into organic matter. Biomass can be directly utilized as fuel or can be converted through different routes into useful forms of fuel. In fact, biomass is a source of five useful agents, which start with `F’ like Food, Fodder, Fuel, Fiber and Fertilizer. Further, biomass has many advantages like.

11.1 General

Biogas is generated through a process of anaerobic digestion of organic materials. The materials normally used are human and animal waste, crop residues, agro-industrial waste and other biomass in a combination with water. Biogas production technology contributes in following ways:

(a)It provides a better and cheaper fuel for cooking, lighting and for power generation.

(b)It produces good quality, enriched manure to improve soil fertility.

(c)It provides and effective and convenient ways for sanitary disposal of human excreta, improving the hygienic conditions.

(d)It generates social benefits such as reducing burden on forest for meeting cooking fuel by cutting of tree for fuelwood, reduction in the drudgery of women and children etc.

(e)As a smokeless domestic fuel, it reduces the incidence of eye and lung disease.

(f)It also helps in generation of productive employment.

The biogas technology is primarily based on fermentation of cellulosic rich organic matter under anaerobic conditions. The methane producing bacteria become more active after the creation of anaerobic conditions, thus, the gas produced become rich in methane & carbon dioxide, beside traces of hydrogen sulphide, ammonia, oxygen, water vapour etc. depending on the feed material and other conditions. For burning of gas, it is necessary that methane contents should be more than 50 per cent. The complete knowledge of process of methane production including its chemistry, physiology, bio-chemistry, micro-biology and bacteriology has been studied over years in many parts of the world. The culture and isolation of microbes under various environmental conditions have been successfully experimented to improve rate of reaction. The conditions, under which cattle dung, organic wastes, bushes, weeds etc. will produce methane, can be understood through chemistry of fermentation.

10.1 Introduction

Winds are the motion of air around the Earth. This movement in air is caused by the uneven heating of the planet’s surface by the sun. The idea of using wind as a form of power is not new. The traditional applications of wind were primarily as sources of kinetic energy for rural, agricultural and a limited number of industrial uses such as pumping water and grinding grain.

Presently wind energy can be used for two major applications, such as wind mills for pumping water for drinking as well as for irrigation purposes and second application is as aero-generator for electricity generation for domestic and industrial uses. In addition to this, presently wind energy battery charger are also available, which can store energy for lights, radio communication, hospital equipment and to power various emergencyrelated equipment.

The wind energy has an enormous resource, but the problems of utilizing the winds are many and varied. Wind energy is very diffuse in nature and local topographical features significantly alter the prevailing winds, thus leading to the extremely site specific nature of wind energy.

Scientists have estimated that as much as 10% of the world’s electricity could be prepared by wind generators by the middle of 21 century. India has estimated wind power potential of 40,000 MW. India now, ranks fourth in the world in wind power generation.

The world’s largest wind farms are in California (USA), where wind turbines can generate power up to about 1120 MW. The first wind mill used as source of electric power was built in Denmark in 1890.

9.1 Introduction

Basically, for heating or cooling the space using solar energy, the solar energy is to be collected, stored and distributed properly in the space to be heated or removed from the space to be cooled. There are two basic approaches for solar houses, there are:

(a)Active solar house technology

(b)Passive solar house technology

In active approach, the solar energy is collected and stored in some separate solar energy collector and then energy is distributed in the space where heating is to be done using electrically operated pumps and fans coupled with radiator etc. The storage of solar energy in active solar house may be in the form of storage as sensible heat or storage as latent heat or chemical heat storage. As per requirement of heating the size of solar collector and storage system be decided. Generally, the active concepts of solar houses are used for heating purpose. Active concept can also be used for space cooling applications. Solar vapor compression and absorption system can be used for this purpose, essentially, this includes incorporation of solar heat collectors, thermal storage system, auxiliary heat supply system (to compensate intermittent nature of sun energy) and control systems. Further, there are three ways of solar space heating i.e. solar air systems, solar liquid systems and solar heat pump systems.

8.1 Introduction

Solar energy can be directly converted into electrical energy. Energy conversion devices which are used to convert sun light into electricity by use of the photovoltaic effect are called solar cells. The advantages of solar cells are:

1.They are reliable, convenient and durable.

2.It is green, sustainable and pollution free technology.

3.Directly solar radiation can be converted into electricity (conversion of global solar light by flat plate photovoltaic).

4.Maintenance cost is quite low therefore suitable even in isolated and remote area, since no moving parts are involved.

5.Solar cells are quite compatible with almost all environments, respond instantaneously with solar radiation.

6.Considerable expected lifetime i.e. 20 years or even more.

7.1 Introduction

A greenhouse is quasi-permanent structure, covered with a transparent or translucent material, ranging from simple homemade designs to sophisticated pre-g\fabricated structures, wherein the environment could be modified suitable for propagation or growing of plants. Materials used to construct a greenhouse frame may be wood, bamboo and steel or even aluminum. Covering can be glass or various rigid or flexible plastic materials. Depending on the covering material, different terminology have been used in the context of greenhouse structures as mentioned below:

Glasshouse: A greenhouse with glass as the covering material is called glasshouse

Polyhouse: It is a greenhouse with polyethylene as the covering material.

6.1. Introduction

Solar crop drying has been demonstrated to be cost effective and an effective alternative to traditional and mechanical drying systems, especially in location with god sunshine during the harvest season. Considerable energy savings can be made with open sun drying since the source of energy is free and sustainable. However, this method of drying is extremely weather dependent and has the problems of contamination, infestation, microbial attacks, etc., thus affecting the product quality. Additionally, the drying time required for a given commodity can be quite long and results in post-harvest losses. Solar drying of agricultural products in enclosed structures by natural convection is an attractive way of reducing post harvest losses and low quality of dried products associated with traditional sun-drying methods. The crop is vulnerable to damage due to hostile weather conditions. The crop is also susceptible to re-absorption of moisture, if it is kept on the ground during periods of no sun, which reduces its quality. This type of problem can be solved by solar dryer. Many dryers have been developed and used to dry agricultural product in order to improve shelf life .Most of these either use expensive sources of energy such as electricity or combination of solar energy and some other form of energy which is not cost effective and dependent on regular supply of fuel.

Principally, drying requires temperature for removing moisture from product, air flow rate to remove moisture from drying chamber and optimum relative humidity within the drying chamber to allow fast drying. These all three requirements for drying can easily be achieved from solar energy. Solar drying is one of the direct applications of solar heat, which involves removal of moisture from the products through the application of solar energy. The removal of moisture requires only low temperature heating, which can be met easily by absorbing solar energy by the surface. This increases the temperature of the air inside the dryer. The moisture produced from the drying product is usually carried out along with the exhaust air. The characteristic of solar energy is good for the drying at low temperature i.e. high flow rates with low temperature rise. The intermittent nature of solar radiation can not affect the drying performance at low temperature. Further, solar energy is available at the site of use and saves transportation cost.

5.1 Introduction

Energy in the form of heat is one of the main energy requirements in domestic, agricultural, industrial and commercial sector of our economy. From an enduse point of view, solar thermal energy finds its application in these areas. Solar thermal energy devices convert radiant energy of the sun into thermal energy for different productive works. In fact, solar energy consists of infrared radiation, it is characteristics of infrared radiation that whenever it falls on any object, it converts into thermal heat energy.

The conversion of sun light into thermal energy is easily or conveniently achieved by means of a metallic or plastic cover, painted black with ordinary black board paint or having selected coating over it and covered with one- or double-glazing cover for transmitting solar radiation inside it. This metallic cover is known as absorber, below it either channels or pipes or passages for allowing entry of water or air are provided, through which heat energy is transferred to working medium either air or water. The absorber plate is covered with suitable thickness of insulating material on its back or sides for preventing loss of heat from the absorber plate. This complete system is enclosed in an airtight box. When exposed to solar radiations, the blackened metallic surface absorbs solar energy and converts into heat. This heat could be used for cooking of food, heating of water and air, evaporation of moisture form the grains etc. In fact, absorber works on the principle of black body, which absorbs maximum and a good absorber, is a good emitter. Hence generated heat could be utilized for different applications.

Horticulture word derived from Latin word: Hortus meaning ‘Garden’ and cultura means ‘cultivation’.

Father of horticulture: Thomas Andrew Knight, John Lindley, Liberty Hyde Bailey.

1^st artificial hybridization in fruit crop in world: T. A. Knight.

Father of vegetables: L. H. Bailey.

1^st book in horticulture: Fruit growing in India: W.B. Hayes (1945) & related to litchi.

Export growth of fresh fruits and vegetables in term of value is 14% and of processed fruits and vegetables is 16.27%.

Contribution of horticulture sector to agriculture GDP (2013-14): 29%.

India is largest producer of Coconut, Cashew, Tea and Spices.

4.1 Introduction

Heat is energy which flows due to difference in temperature. Whereas energy is stored heat. Therefore, when the heat energy transfer is completed. It is stored in the form of potential or kinetic energy, in general as internal energy. Heat as energy is measured in terms of observed changes in other forms of energy & other physical properties. A heat transfer analysis is required for estimating the size, the efficiency and cost of the equipment necessary to transfer a specified amount of heat in a given time. It is well known fact that the size of a solar collector or a heat exchanger depends not so much on the amount of heat to be transmitted but rather on the rate at which heat is to be transferred under given conditions.

4.2 Modes of Heat Transfer

Heat is transferred from one body to another in three possible ways, conduction, convection, and radiation.

3.1 The Sun

The Sun is a star. It is a huge, spinning, glowing sphere of hot gas. It appears so much larger and brighter than the other stars because we are so close to it. The Sun is the center of our Solar System and contains most of the mass in the Solar System. All of the planets in our Solar System, including Earth, orbit around the Sun. In sun the energy generation is a multi-step process of thermo-nuclear fusion reactions. In the thermo nuclear fusion hydrogen (four protons) combines to form helium (one helium nucleus). The mass of the helium nucleus is less than that of four hydrogen protons and mass having been lost in the reaction is converted to energy. The reaction is represented as

2.1 Introduction

The name thermodynamics stems from the Greek words therme (heat) and dynamis (power), which is most descriptive of the early efforts to convert heat into power. It may be defined as the science that deals with the relations among heat, work and properties of a system. Today, thermodynamics is broadly interpreted to include all aspects of energy and energy transformations, including power generation, refrigeration, and relationships among the properties of matter. It is viewed as the science of energy, and thermal engineering is concerned with making the best use of available energy resources.

Thermodynamics basically entails four laws or axioms known as Zeroth, First, Second and Third law of thermodynamics.

The zeroth law deals with thermal equilibrium and establishes a concept of temperature.

The first law pertains to the conservation of energy and introduces the concept of internal energy.

The second law indicates the limit of converting heat into work and introduces the concept of entropy.

The third law defines the absolute zero of entropy.

The concept of energy was introduced by Newton in the field of mechanics during generalizing the hypothesis of kinetic and potential energies. Energy may be defined as the capacity to do work and it is a scalar quantity. It cannot be seen or observed. Its presence can, however, be felt by the properties of the system. There occurs a change in one or more properties of the system in case of energy transfer. The absolute value of energy of a system is difficult to measure, whereas the energy change is rather easy to calculate. Energy follows the conservation law, one of the most fundamental laws of nature, which simply states that during an interaction, energy can change its form from one form to another but the total amount of energy remains constant, that is, energy cannot be created or destroyed only form can be changed.

1.1 General

Renewable technologies are considered to be clean sources of energy. The optimal use of these resources minimize environmental impacts, produce minimum secondary wastes, and are sustainable based on current and future economic and social needs. Sustainable development requires methods and tools to measure and compare human activities’ and its environmental impacts for various products. Renewable energy sources (RES), which include biomass, hydropower, geothermal, solar, wind, and marine energies, supply 14% of the world’s total energy demand. Renewable resources refer to primary, domestic, and clean or inexhaustible energy resources. Large-scale hydropower energy supplies 20 % of the global electricity need. Wind power in coastal and other windy regions is a promising source of energy.

Renewable energy resources can make a decisive contribution to the economic, social and sustainable development of rural regions in developing countries, yet the consumption of fossil fuels is dramatically increasing along with improvements in the quality of life, the industrialization of developing nations, and the increase of the world’s population. It has long been recognized that excessive consumption of fossil fuel leads not only to a diminishing fossil fuel reserves more quickly, but also has a significant adverse impact on the environment. Such impacts result in increased health risks and the threat of global climate change. Changes to improve environmental conditions are becoming more politically acceptable globally, especially in developed countries. Society is slowly moving towards seeking more sustainable production methods, minimizing waste, reducing air pollution from vehicles, generating distributed energy, conserving of native forests, and reducing greenhouse gas emissions. Increasing consumption of fossil fuel to meet out current energy demands, however, has sounded alarms over regarding potential energy crisis. This has generated a resurgence of interest in promoting renewable alternatives to meet the developing world’s growing energy needs. Excessive use of fossil fuels has caused global warming from carbon dioxide emissions, therefore, promoting renewable forms of clean energy is eagerly required. To monitor the level of these greenhouse gas emissions, an agreement that has fulfills the objectives of the Kyoto Protocol was create with overall pollution prevention targets.

19.1 DEFINITION OF ORGANIC FARMING

1.According to IFOAM (International Federation of Organic Agriculture Movement), Organic Farming definition includes all agricultural system that promote the environmentally, socially and ecologically sound production system of food and fibres. IFOAM stresses and supports the development of self- supporting system on local and regional level.

2.As per the definition of the USDA study team on organic farming “organic farming is a system which avoids or largely excludes the use of synthetic inputs (such as fertilizers, pesticides, hormones, feed additives etc) and to the maximum extent feasible rely upon crop rotations, crop residues, animal manures, off-farm organic waste, mineral grade rock additives and biological system of nutrient mobilization and plant protection”.

3.In another definition FAO suggested that “Organic agriculture is a unique production management system which promotes and enhances agro-ecosystem health, including biodiversity, biological cycles and soil biological activity, and this is accomplished by using on-farm agronomic, biological and mechanical methods in exclusion of all synthetic off-farm inputs”.

18.1 INTRODUCTION

The decline in productivity of old and senile orchards existing in abundance has become a matter of serious concern for the orchardists, traders as well as scientists. In India 30-35% area under fruit crops is occupied by old, senile, and pest-and-disease- affected orchards. For overcoming the problem of unproductive and uneconomic orchards existing in abundance, large scale uprooting and replacement with new plantations will be a long term and expensive strategy. Thus, rejuvenation of old and senile orchards is a good alternative.

17.1 INTRODUCTION

Bearing habit indicates position of f lower bud with respect to vegetative growth of the plant after cessation of juvenility. Different fruit trees have different bearing habits. The knowledge of bearing habits will be of much importance for regulating the bearing of any plant by means of pruning. Terminal bearers are not normally pruned, whereas in case of lateral bearers pruning certainly increase the bearing, as it encourages the sprouting of lateral buds. Fruit trees may bear the fruits either terminally on a long or short growth, laterally on present or past season growth or adventitiously from any point on the trunk or root. The relative position of a fruit with reference to its potential bud giving rise to f lower or inf lorescence in the shoot is known as bearing habit. Knowledge on the bearing habit is a pre-requirement before performing pruning in any fruit crop (particularly in ber, guava, grape etc.). Proper understanding of bearing habits helps a lot in manipulating time and period of f lowering and fruiting which consequently inf luence harvesting and yield of better-quality fruits.

16.1 INTRODUCTION

Mulch, a technical term, means ‘covering of soil’. A mulch is a layer of material applied to the surface of soil. It may be applied to bare soil or around existing plants. Mulches of manure or compost will be incorporated naturally into the soil by the activity of worms and other organisms. Mulching is the process or practice of covering the soil/ground to make more favourable conditions for plant growth, development and efficient crop production. While natural mulches such as leaf, straw, dead leaves and compost have been used for centuries, during the last 60 years the advent of synthetic materials has altered the methods and benefits of mulching. The research as well as field data available on effect of synthetic mulches make a vast volume of useful literature. In this manner it plays a positive role in water conservation. The suppression of evaporation also has a supplementary effect; it prevents the rise of water containing salt, which is important in countries with high salt content water resources.

15.1 INTRODUCTION

Cropping system is defined as a cropping pattern followed on a farm and its interaction with farm resources, other farm enterprises and production technology. In other words, cropping system refers to a combination of crops in time and space. When annual crops are considered, a cropping system usually means the combination of crops within a given year (Willey et al., 1989). This cropping system might provide insurance against crop failure by reducing disease (Fininsa and Yuen, 2002) and insect incidence (Gahukar, 1989) or against unstable market prices by planting two or more crops under intercropping and thus, reducing the risk of unexpected changeable prices. Intercropping in scientific way should be viewed from a theme of competition to one of collaboration with mutually beneficial relation with proper planning to get more return from limited natural resources. Legumes have been the common intercrops in any intercropping system owing to their short duration, N-fixing ability etc. Even though non-leguminous vegetables require longer duration than legumes and are non-N-fixers, they can also be suitable as intercrops because of their high profitability and higher yields.

14.1 INTRODUCTION

India is conferred with a varied agro-climatic condition which are highly favourable for growing a large number of horticultural crops such as fruits, vegetables, root tubers, ornamental, aromatic plants, medicinal herbs, spices and plantation crops like coconut, areca nut, cashew and cocoa (Ministry of Information and Broadcasting, GOI, 2008). India is next only to China in area and production of vegetables and occupies prime position in the production of caulif lower, second in onion and third in cabbage in the world. After achieving food security, it is being increasingly felt that India needs to achieve nutritional security for betterment of its population. In achieving nutritional security fruits and vegetables play an important role (Ganeshmurthy et al.2011). Although we have achieved good production levels of fruits and vegetables, the present production of fruits and vegetables may not be enough to meet out the demand. To feed the ever-increasing population in a sustainable way a tremendous effort will have to be made to increase the production of fruits and vegetables both horizontally and vertically through a rational and balanced use of production inputs, specially the mineral fertilizers. Soil fertility is a key factor for successful crop production, and it is a measure of capacity of soil to supply plant nutrients. The importance of soil fertility and fertilizer management is being increasingly recognized in all countries recently to meet the demand for food and other agricultural raw materials. Intensive use of fertilizer, intensive cropping with high yielding cultivars have increased the food production and reduced the food shortage, but it has also brought in numerous problems of soil fertility, soil and water pollution. On the other hand, fast depletion of nutrients due to over exploitation, a wide-spread deficiency of N, P, K and S coupled with micro-nutrients deficiencies especially Zn and boron has been noticed in many soils. Further deforestation, shifting cultivation, burning of trees, bushes, grasses and cow dung, soil erosion, soil degradation, nutrient losses, excessive fertilizer application, leaching losses etc., have aggravated the depletion of soil fertility status. It is being realized that the future of Indian agriculture is closely related to scientific management of soil fertility along with judicious and efficient use of fertilizers. Soil fertility and nutrient management is one of the important factors that have a direct impact on crop yield and quality. Soil test reports help in determining soil organic matter, pH, electrical conductivity, cation exchange capacity, and levels of important macronutrients (phosphorus, potassium, calcium, magnesium) and micronutrients (boron, zinc, etc.). These reports also help estimating lime or sulphur application rates to increase or reduce soil pH, respectively. Maintaining a soil pH between 6.0 and 7.0 is recommended for most crop rotations that include vegetable crops.

13.1 INTRODUCTION

Weed is defined as an unwanted plant growing at a place where it is not desired. Weeds are unwanted and undeserved plants that interfere with the utilization of the land and water resources and thus adversely affect crop production and human welfare. Thus, a plant out of its place or a plant growing where it is not desired at that time is a weed. Weed has no species, but name was suggested as a useless and harmful plant that persistently grows where it is quite unwanted. According to Jethro Tull, the father of Weed Science, weed is defined as the unwanted, undesirable plant, growing out of their proper place, which interfere with the utilization of natural resources, prolific, persistent, competitive, harmful and even poisonous in nature and can grow in adverse climatic conditions. Of the total losses caused by pests, weeds have a major share (30%). They reduce the crop yield and decrease the quality of produce and hence reduce the market value of the turnout. Weeds are a major problem to horticultural production as they take advantage of their initial slow growth rate. Weeds reduce crop yield, lower their quality, act as alternate host of many pests/diseases and also have allelopathic effects on crops. Weeds also interfere with vital farm operations like weeding, fertilizer application, herbicide application and harvesting. Both annual and perennial weeds are common in their actions reducing the productivity of fruit trees. Weeds also provide shelter to various pathogens by becoming an alternate or collateral host of invaded crops by a number of fungal, bacterial and viral diseases.

The worst weeds found in the world are Cyperus rotundus, Cynodon dactylon, Echinochloa crusgalli, Echinochloa colona, Eleusine indica, Sorghum halepense, Imperata cylinderica, Eichhornia crassipes, Portulaca oleracia, Chenopodium album, Digitaria sanguinalis, Convolvulus arvensis, Avena fatua, Amaranthus hybridus, Amaranthus spinosus, Cyperus esculentus, Paspalum cojugatum, Rottboelia exaltata (Rana and Rana, 2016). All of these weeds are found in India. It has been reported that about 36-42% losses may occur due to inadequate management of weeds in apple (El- Metwally and Hafez, 2007). Therefore, management of weeds in all agro-ecosystems is crucial to sustain our crop productivity and to ensure the food security to the rapidly increasing population.

12.1 INTRODUCTION

Water is a factor of prime importance in agriculture industry. Water management is one of the largest and most important inputs into an orchard. An efficient water management refers to artificial application of water, i.e., irrigation in crop root zones in case of soil moisture deficit and removal of water, i.e., drainage from the root zone in case of excess so as to provide the crops a most optimum soil moisture regime for best production. It means how best we are in irrigating and dewatering our fields so that plants are protected from stress as well as water logging (Goswami, 2015). Water resources are continuously overburdened with excessive drafts and water sources are shrinking at faster rate. Groundwater levels are falling at the rates faster than ever. Under this type of circumstances, judicious use of water should be given due attention for water conservation and also in increasing water productivity. Area under horticultural plantations is increasing at exponential rate. The unproductive uplands and low productive midlands and lowlands are brought under fruit based horticultural plantations. For a profitable orchard enterprise, a well-planned irrigation system and efficient water management practice are of utmost importance. Horticultural sector, which includes vegetables, f lowers and fruits, has enormous potential for development owing to varying agro-climatic conditions in India. There is tremendous scope for increase in productivity and quality of horticultural crops, which is necessary to compete in this modern competitive world market. There are many production technologies available to increase the per unit vegetable production and also to increase its quality. One of the widely acceptable, reliable and cost- effective technologies is pressurized irrigation.

11.1 INTRODUCTION

Plant growth regulators have remained an important component in horticulture from time immemorial because they were effective means of quantitative as well as qualitative improvement in growth and development of crops. Plant Growth Regulators (PGR) are diverse group of organic compounds other than nutrients, produced artificially or by plants which in low concentrations promote, inhibit or modify the physiological process in plant. The term includes both naturally occurring phytohormones as well as synthetic compounds. These are produced naturally in higher plants, controlling growth or other physiological functions at a site remote from its place of production and active in minute amounts. Plant Growth Regulators are used in different forms like liquid, powder, paste etc. “Hormone” is Greek word derived from “hormao”, which means to stimulate. Thimone (1948) suggested the use of term ‘phytohormones’ as the organic substance, which are produced naturally in plants, synthesised in one Part And usually translocated to other part wherein every small quantity affects the growth and other physiological function of the plants. To distinguish them from the animal hormones they are termed as phytohormones. Auxin was the first hormone to be discovered in plants and at one time considered to be only naturally occurring plant growth hormone. The role of plant growth regulators in various physiological processes such as seed germination, f lowering, fruiting, seed development, fruit ripening and yield etc. in different crop plants is well established (Kiran et al., 2011). There are five classical phytohormones: auxins, gibberellins, cytokinins, ethylene and abscisic acid. Besides classical phytohormones a variety of other compounds that play roles in plant growth and development have also been identified, including jasmonic acid, salicylic acid, brassinosteroids and polyamines (Basra, 2000). The application of plant growth regulators in agriculture has started in 1930 in the United States. Ethylene, a naturally occurring substance, is one of the first plant growth regulators being discovered and used successfully for enhancing f lower production in pineapple (Fishel, 2006). Its toxic effects to human beings are low.

10.1 INTRODUCTION

Most botanists identify trees by their leaves, f lowers and fruit. However, the plant architecture specialist is interested in trunks, branches and twigs. All types of fruit tree do not require pruning, e.g., mango, sapota, while some fruit trees can grow well naturally, e.g., pineapple, papaya as they do not require pruning. Most deciduous trees like apple, pear, almond etc. and grapes, ber, fig, citrus, pomegranate, guava etc. require pruning to train them for desired shape.

10.2 TRAINING

Training is an operation by which the plant is made to develop an orderly structure or frame work. This is done by staking, tying, supporting, propping, trailing or spreading on certain structure with or without pruning of plant. Training is usually done when plants are young. Bending, twisting, decapitations are done by using springs of hard wire, where it is required. It is a physical technique which controls the shape, size and direction of plant growth known as training or in other words, training in effect is orientation of plant in space through techniques like tying, fastening, staking, supporting over a trellis or pergola in a certain fashion or pruning of some parts.

9.1 INTRODUCTION

Establishment of an orchard incurs long term investment for which it needs a very critical planning. As it is a long-term investment, plants planted in the orchard should suit to the prevailing climatic condition of that area. The land remains occupied as long as 40 to 50 years. Any mistake committed during initial year is hard to rectify later on. Proper layout of the orchard ensures optimum utilisation of land and resources for successive economic production. It becomes easy for different inter-cultural operations, harvesting and transportation of the produces. Uniform distribution of plants in the selected land in various systems of planting is done after proper layout.

9.2 LAYOUT

The proper layout of orchard aims at accommodating maximum number of trees per unit land area, maintaining adequate space for proper development of the trees and convenient orchard management practices.

8.1 INTRODUCTION

Orchard is a place or a piece of land where different kinds of fruit plants are planted in orderly manner and managed efficiently for production of successive yield to get assured economic return. An orchard being capital-intensive and long-term venture careful planning, layout, selection of site, preliminary operations etc. are to be done. It is easy to establish an orchard considering its features critically but difficult to manage afterwards. It needs high managerial skills and technically skilled manpower to carry out different orchard operations. Any lapses in management can lead to incur heavy loss.

7.1 INTRODUCTION

Gardening is a practice of growing different kinds of horticultural crops in a particular land area as a part of horticulture either for consumption or sale, export, beautification etc. Basing on the crops grown, gardens are named accordingly, e.g., for raising vegetables, it is vegetable gardens; for fruit crops, it is orchard; for plantation crops, it is estate plantation; for ornamental plants, it is gardening and landscape etc. The history of gardening is not new. In ancient time kings, emperors, rulers, sages were establishing different types of gardens for different purposes.