eChapters

12.1 Introduction

Rainfall is the major source of water that contributes lion’s share for irrigation to crops. Before it reaches the earth, it is to a great extent pure in nature. By the time it falls on the ground surface, it comes in contact with various types of gases and suspended materials of the atmosphere and also after it flows as runoff on the surface it gets dissolved with many types of salts, impurities etc. that render the water to be impure. Many a time the industrial waste, agricultural wastes, pesticides, fungicides, chemical fertilizers etc. get mixed with water and make it unsuitable for irrigation use. Water being a universal solvent, it dissolves all most all organic impurities, salts etc. which makes it objectionable for both domestic and agricultural uses.

Irrigated agriculture is dependent on an adequate water supply of usable quality. In the past, water quality concerns were neglected because good quality water supplies were plentiful and readily available. This situation is now changing in many areas. Especially, in the arid and semi-arid zones, water quality is fast deteriorating which is posing threat to irrigated agriculture.

Conceptually, water quality refers to the characteristics of a water supply that will influence its suitability for a specific use. On the other hand, it refers to the situation of how well the quality meets the needs of the user. There are three quality indicators. They are physical, chemical and biological indicators. Even a personal preference such as taste is a simple evaluation of acceptability. For example, if two drinking waters of equally good quality are available, people may express a preference for one supply rather than the other; the better tasting water becomes the preferred supply. In irrigated agriculture, emphasis is placed on the chemical and physical indicators of the water and rarely the biological indicator is considered important.

8.1 Introduction

Cartilaginous fishes have ventrally placed mouths with teeth in several series. They possess rigid dorsal fins and placoid scales. They have five pairs of gill clefts opening individually to the exterior, a lower jaw articulated with the upper jaw and upper jaw not fused to the skull, no swim bladder, an operculum, an endolymphatic duct and a heterocercal or homocercal tail. It shows internal fertilization, meroblastic cleavage and direct development.

Elasmobranchii includes a wide range of cartilaginous fishes. Dogfish sharks are commonly studied all over the world probably because of their suitable size for dissection.

Phosphorus is the second important key element after nitrogen as a mineral nutrient in terms of quantitative plant requirement (Donahue et al., 1990), which is required in optimum amount for proper growth of plants and soil micro-organisms. Being a constituent of ATP, it is involved in various processes such as cell division, energy transduction through photosynthesis and biological oxidations and uptakeof nutrients. The average soil contains 0.05% phosphorus, but only one tenth (1/10) of this is available to plants due to its poor solubility and chemical fixation in soil (Barber, 1984). About 98% of Indian soils have inadequate supply of available phosphorus (Ghosh and Hassan, 1979). A survey of Indian soils showed that out of 363 districts, only 2.2% were high, 51.5% medium and 46.3% were low in phosphorus content (Ghosh, 1982).

Cable conveyor: A power conveyor in which a trolley runs on a flexible, torque transmitting cable that has helical threads.

Cable: 1. A general term applied to rope or chain used for engineering purposes. 2. The standard wire with insulating cover used for conducting electrical current.

Cage harrow: A rolling harrow with horizontal shafts each fitted with star shaped tines joined by rods forming the lines of cylinder.

Radionuclides are used in two major ways: for their chemical properties and as sources of radiation.

Radionuclides of familiar elements such as carbon can serve as tracers because they are chemically very similar to the non-radioactive nuclides, so most chemical, biological, and ecological processes treat them in a near identical way. One can then examine the result with a radiation detector, such as a Geiger counter, to determine where the provided atoms ended up. For example, one might culture plants in an environment in which the carbon dioxide contained radioactive carbon; then the parts of the plant that had laid down atmospheric carbon would be radioactive.

In medicine, radioisotopes are used for diagnosis, treatment, and research. Radioactive chemical tracers emitting gamma rays that can provide diagnostic information about a person’s internal anatomy and the functioning of specific organs. This is used in some forms of tomography single emission computed tomography and positron emission tomography scanning. Radioisotopes are also a promising method of treatment in hemopoietic forms of tumors, while the success for treatment of solid tumors has been limited so far. More powerful gamma sources are used to sterilize syringes and other medical equipment. About one in two people in Western countries are likely to experience the benefits of nuclear medicine in their lifetime.

In biochemistry and genetics, radionuclides are used to label molecules and allow tracing chemical and physiological processes occurring in living organisms, such as DNA replication or amino acid transport.

5.1 Introduction
Since the early days of human interaction with the environment, particularly in industrial settings, humans have continually been “shaped” to meet the demands of their surroundings. Historically, people have often endured significant discomfort and limitations without much complaint. In metaphorical terms, individuals have adapted by extending their reach to operate controls that were difficult to access, pushing their perceptual abilities to detect faint sounds or invisible signals, and compressing their bodies to fit into cramped workspaces. Cognitive abilities have also been stretched to accommodate monotonous or tedious tasks. However, as both work environments and machines have grown more complex, these challenges have become increasingly significant. A poor “fit” between the human operator and their environment has led to countless accidents, decreased productivity, and errors in many industries. The primary goal of ergonomics is to assess human capabilities and design the environment to align with these capabilities. Instead of attempting to adapt humans to jobs, ergonomics strives to “fit the job to the person.” This approach aims to optimize safety, efficiency, and comfort by aligning machine requirements with the operator’s abilities. By establishing a connection between humans and machines, ergonomics ensures that machines communicate information to the operator through their sensory systems, prompting a response that may alter the machine’s state. Key environmental factors such as temperature, humidity, lighting, sound, and visual conditions have a direct impact on both human well-being and the quality of production. The design of both the human workspace and the equipment used can be highly effective if the environment is conducive to the operator’s needs. Therefore, it is essential to study each environmental factor from an ergonomic perspective to ensure a comfortable and productive environment for workers. This includes designing jobs, equipment, and considering human anthropometric measurements in the design process.
5.2 Heat
Heat stress occurs as a result of the combined effects of environmental conditions, physical exertion, and clothing. The key environmental factors influencing heat stress include air temperature, humidity, radiant heat, and air movement, all of which can significantly affect work performance. Heat strain refers to the

Artificial intelligence is becoming an important technology for transforming agricultural decision-making and farm management. This chapter introduces the fundamental concepts, tools, and applications of AI in agriculture. It explains how machine learning, deep learning, computer vision, predictive analytics, and intelligent systems can process large volumes of agricultural data. AI applications include crop monitoring, disease detection, yield prediction, precision input management, and automated decision-making. The chapter also discusses the major drivers of AI adoption, including increasing food demand, resource constraints, climate change, and labour shortages. Examples of AI-based agricultural applications demonstrate its potential to improve productivity, sustainability, resource efficiency, and resilience.

A. Successful Biological Control Projects

Biological control, the use of natural enemies to manage pest populations, has seen numerous successful implementations globally for example:

1. Control of Cottony Cushion Scale (Icerya purchasi)

The case of the cottony cushion scale, Icerya purchasi, in California's citrus orchards serves as a seminal example of biological control's efficacy. Originating from Australia, this pest posed a severe threat to the burgeoning citrus industry in California in the late 19th century. The story of its control through the introduction of natural enemies is not only a landmark in biological control history but also a demonstration of ecological problem-solving.

Background and Impact

Icerya purchasi is a sap-sucking insect that infests a wide range of host plants but shows a particular fondness for citrus trees. The infestation is damaging as the scale excretes a sticky substance known as honeydew, which promotes the growth of sooty mold, impairing photosynthesis and weakening the plants. The severity of the infestation threatened the economic viability of the citrus industry in California during the 1880s.

Introduction

Micro, small, and medium enterprises (MSMEs) dominate the Indonesian economy. These enterprises account for around 99 percent of all businesses in Indonesia and employ more than 95 percent of the total workforce across the country. They should be the primary engines of economic growth, although they generate only approximately 56 percent of the overall gross domestic product (GDP) of Indonesia. Around 80 percent of MSMEs are in the trading sector involved in buying and selling existing products/services). Within the MSME group, micro and small enterprises (MSEs), including those in the manufacturing industry, called micro and small industries (MSIs), i.e. business units with up to a maximum of 500 million Indonesian rupiah (IDR), are the ones that receive the most attention from the Indonesian government because they account for almost 99 percent of total MSMEs. So, compared to medium and large industries (MLIs), MSIs are the largest job creators in the country. These enterprises also have high resilience in various previous crises, including the COVID-19 pandemic. Their high resilience has played a role as a cushion for the economy because of their ability to survive periods of pressure and grow back faster and higher after pressure.

1. Introduction

Fruits and vegetables represent highly perishable items of agriculture, mainly because of their high water content in fresh form. Their production, yield and management under agriculture is dealt essentially under horticulture. They abound in species and varieties in different geographic regions of the world, influenced by the agro-climatic conditions. Some are endemic and confined to certain geographic regions only. Accordingly, they may be tropical, sub-tropical or temperate, depending on their requirements of temperature for growth and yield.

Abstract

The objective of this chapter is to provide an overview of heat pump dryer (HPD) and recent developments in its applications for drying of agricultural and food products. The basics of heat pump dryer, classification, operating principle, configuration and control system have been presented for better understanding. Many researchers have concluded that HPDs use energy more efficiently than electrical dryers. The heat pump dryer is best suited for drying high value commodities such as fruits, vegetables, spices, condiments, herbs, medicinal and aromatic plants at near ambient temperature for producing better quality dehydrated product.

1. Introduction

Vegetables and fruits are the next in demand for human consumption after rice and wheat, in all parts of the globe. Fresh fruits & vegetables and their value added products are increasing in popularity day by day almost in all the countries, because of their richness in dietary fibre, minerals & vitamin contents and for their medicinal properties. Maintaining agricultural produce quality and its evaluation are thus naturally important. Decisions concerning maturity and ripeness of fruits and vegetables are based mostly on visual inspections, which are subjective in nature. The quality of fruits and vegetables is mostly decided on the basis of size, shape, colour, gloss, flavour, firmness, texture, taste and freedom from external as well as internal defects. Internal quality factors such as maturity, sugar content, acidity, oil content and internal defects, however, are difficult to evaluate non-destructively. Methods are needed to better predict the internal quality of fruits and vegetables without their destruction. Recently, there has been an increasing interest in non-destructive methods of quality evaluation, and a considerable amount of effort is being made in this direction. But the real problem is how these methods are to be exploited practically on commercial scales and what are the constraints faced in implementing them.

Modern farm planning involves nonlinear, discontinuous and multi-objective problems that conventional optimization methods may not solve effectively. This chapter examines Genetic Algorithms, Particle Swarm Optimization and Differential Evolution for improving agricultural resource allocation. These nature-inspired techniques can simultaneously address crop yield, water use, fertilizer application, environmental effects and financial viability. Their integration with deep-learning forecasts and crop-simulation systems enables more realistic optimization. Multi-objective evolutionary algorithms identify Pareto-optimal alternatives, allowing decision-makers to balance productivity and ecological sustainability. The chapter also emphasizes explainable artificial intelligence, economical implementation and farmer usability as necessary conditions for transferring evolutionary optimization methods from experimental research to practical farm management.

Abstract
 
Grains are usually harvested above 20% (wb) moisture level and they are prone to microbial attack at high moisture level. In order to avoid both qualitative and quantitative losses that arise from microbial growth, grains are usually dried to safe moisture level. The safe storage moisture content may vary from 8-16% (wb), depending upon the grain and climate type. Therefore, drying is a necessary step in preventing these losses. Drying also reduces the bulk weight of the materials, thus easing transportation and storage. Drying can occur in thin layer or in deep bed. Different drying theories are proposed to characterize these drying processes. Theoretical as well empirical drying equations have been developed.

Natural resources conservation and their management hold key to sustainable agriculture and livestock production. It is all the more crucial for countries with predominant agrarian economies where development of sustainable agriculture is essential for overall growth, redressal of poverty and security. Conservation of both soil and rain water as very crucial and basic resources have been practiced since ancient times in India. However, there has been renewed emphasis on conservation and efficient utilization of these resources in the recent past. The fact that 70% of the arable area of India is rainfed with precarious supply of water and that rainfed agriculture supports 44% of India’ s human population and contributes 90 per cent of coarse cereals and pulses, 80 per cent of oilseeds and 65 per cent of cotton and growing realization that further gains i n productivity of crops and livestock will emanate from rainfed regions, leave no room for complacency in this regard.

Year after year, the fate of a vast ‘majority of Indian farmers hangs in balance, as success with rainfed agriculture continues to be a gamble. It is evident that crop yields in semi-arid areas depended more on rainfall distribution than on total rainfall and lack of serious efforts to create d water supply for crops through scientific management of rainwater is a factor favouring this avoidable uncertainty. In rainfed agriculture no other input can perhaps enhance the yield without effectively tackling of the rainfall aberration related sub-optimal moisture availability. Therefore a prerequisite for substantial improvement in the agriculture production in the semi-arid region is to manage runoff water and to use it either at the time of moisture stress even during the monsoon or in next season. It has been reported that only one supplementary irrigation at proper stage can double of Rabi crops. But supplemental water is a developed resource and is more expensive than the natural resources. Hence, it is all the more necessary to use this water judiciously and efficiently. Standardization of techniques by which as much of precipitation as possible can be conserved for crop use, either directly in the soil profile through infiltration or through runoff collection and recycling is an area of priority in research.

Cauliflower
Cauliflower, Brassica oleracea L var. botrytis under the family Brassicaceae (Cruciferae) having chromosome No. 2n = 2x =18 is the most popular vegetable among the cole crops, particularly in Asia. It is grown in all continents of the world,= of which Asia is the leading one followed by Europe and covers small acerages in North America, South America, Africa, Australia and New Zealand. India and China together have about 60 % of total cauliflower area of the world. Cauliflower is used in different curry and fry preparations with potato, garden pea, sweet pepper and other vegetables. It contains high quality proteins and good in stability of vitamin C after
cooking. Frozen products are also prepared from cauliflower. It is rich in minerals such as potassium, sodium, iron, phosphorus, calcium, magnesium, etc.
Origin, domestication and adaptation in India
The cole crops have originated from the wild diploid species Brassica oleracea var. sylvestris mainly by mutation, human selection and adaptation. This wild species, a leafy kale-like plant which occurs in the northern shore of the Mediterranean Sea an along the lime cliffs in north-eastern England and North Sea is the progenitor of th cultivated kale and leafy non-heading cabbage. Probably kale was the first cole crop to have selected and adapted by man. From this leafy kale-like plant (Brassica oleracea var. sylvestris), other cole crops viz., kale, collard, broccoli, cauliflower and cabbage have been descended.

1. Introduction

In this era of genomics, proteomics and metabolomics the challenge in nutritional science is to clarify human nutrient requirements and design nutritional strategies to promote health and functional longevity. Our ancient Indian belief that ‘we are what we ate’ and our future health as individuals may well depend upon what we eat today. Plant-based dietary antioxidants are believed to have an important role in the maintenance of human health because our endogenous antioxidants provide insufficient protection against the constant and unavoidable challenge of reactive oxygen species (ROS). We have various endogenous defense chemicals but they are inadequate to prevent oxidative damage that makes human system prone to various degenerative diseases. Hence, it is necessary for increased intake of dietary nutraceuticals that may help maintain the balance between oxidants and antioxidants, slow age-related changes, and prevent onset of degenerative diseases.

1. Introduction

Pulpy and juicy fruits like orange, guava, banana, grape, mango, papaya, pears, apples and jackfruit can be converted into fruit products like squashes, juices, cordials and ready-to-serve (RTS) fruit beverages. These RTS fruit beverages are both refreshing and thirst quenching and have become very popular. Liquid fruits are the clarified juices prepared from these pulpy and juicy fruits. There is a demand for liquid fruits in the international market for various applications. The liquid fruits can be used as a natural alternative to synthetic beverages. They can be suitably concentrated or diluted, blended with other juices and also can be carbonated as fruit based soft drinks. Removals of pulpy material from the juices make them easier to preserve by pasteurization and are amenable to carbonation. Pulpy fruits can be successfully processed into liquid fruits (clarified juices) by using pectic enzymes. The emphasis of the fruit juice processing industry has, so far, been mainly on conventional clarification processes like enzymatic and chemical treatments followed by filtration using filter aids; and concentration by vacuum evaporation.

Chickpea (Cicer arietinum L.) is a self-pollinating diploid (2n=2x=16) with a genome size of 740 Mbp and belongs to family Fabaceae (or Leguminosae). In a scientific advance involving scientists from more than 20 research organizations, sequencing of the chickpea genome was recently completed for 90 chickpea genotypes, including several wild species. The researchers responsible for the work, led by ICRISAT, succeeded in identifying more than 28,000 genes and several million genetic markers that scientists expect will lead to the development of superior varieties.

1. Introduction

Intermediate moisture foods are semi moist foods that have some of their water bound by glycerol, sorbitol, salt or certain organic acids, thus preventing the growth of many microorganisms (Stewart et al. 2001). It is now well recognized that fruits and vegetables are dehydrated to an intermediate moisture level (20-50%) (Stewart et al. 2001; Purvi et al. 2003). As the intermediate moisture products are characterized by a semi moist consistency so these foods have enough moisture content to permit easy chewing but low enough water content to prevent spoilage production of intermediate moisture foods is based on an increased scientific understanding of the chemical reactions involved in traditional food preservation methods (Purvi et al. 2003).
There will be better retention of original flavor and texture compared to fully dried products, with concomitant reduction in bulk, weight and cost of packaging, transportation and storage. Such intermediate moisture foods are more appropriate for developing countries in view of their minimal processing requirements, stability under ambient conditions, safety, convenience, ease of nutrient content adjustment, energy savings and low capital investment. They are also eminently more suited than dehydrated or canned foods for military rations (FAO, 2005).