eChapters

The purpose of a sub-surface drainage system is to lower the ground water table and removal of salts beyond the crop root zone. The ground water beyond table may rise due to commonly practiced flood irrigation method, seepage from unlined channels, percolation of rain and runoff water and sub-surface flow from higher areas. Sub-surface drainage consists of drains laid at a specified depth, spacing and grade below the ground surface. The size, spacing and depth of drains depend largely on the soil-water properties viz., infiltration, saturated hydraulic conductivity, drainable porosity; and the requirement of removal of water through drains in certain time period fixed on the basis of rainfall and crop cultivated. The drains are usually placed in a pervious stratum. Suitable filter of coarse sand and gravel may be used when it is placed in a low permeable stratum. Sub-surface drainage serves the important job of removal of concentrated salt solution from the crop root zone particularly in arid and semiarid region.

Advantage of sub-surface drainage system

1. Since sub-surface drainage are underground, no loss of land for cultivation. Some part of the land goes out of use for making drains in surface drainage.

12.1 Introduction

Agricultural drainage is the removal of excess water from the farmland for the purpose of providing favorable soil air environment for plant growth. Removal of water may take place form the surface or below the surface of the land. The practice of lowering ground water table below the root zone depth to improve the plant growth or to reduce the accumulation of salts in soil is also called as drainage

Drainage system is broadly classified as surface & subsurface drainage. Removal of excess water over the land surface is known as surface drainage & that of removing water below the surface is known as subsurface drainage. The flow of water in the form of evaporation or evapotranspiration also play important role in improving drainage situation. It gives the idea of the time required to get the wetland workable though it is not called a type of drainage as because this is very slow process & cannot be controlled by the human activities. However, using of certain tree plants e.g., Eucalyptus, Poplar, Casurina or similar species in wet fields, which transpires at high rate and improves the drainage problem by lowering the shallow water table is the new idea known as bio-drainage.

10.1 Land and Water Resource

India has got the world’s 2.45% area and 16.87% of population with only the 4% of available fresh water (Table 11.1). This indicates the necessity of development of water resources and optimal use of it. India at macro level does not have short of water. But the shortage of water is due if not properly managed by conservation and sector wise utilization.

The water resource potential of the country has been assessed by different agencies in different time (Table 11.1). It is observed that the latest estimate of 1869bcm (1993) are within the little variation of the estimates since 1954. The utilizable water resources of the country are assessed 1123bcm by CWC (1993) of which 690bcm from surface water and 433bcm from ground water sources. This 690bcm can be harnessed if matching storage structures are built. The surface water utilizable potential may increase by 220bcm if inter-basin transfer

Poor quality of water is one of the important factors causes gradual accumulation of salts on the ground or in the root zone of crops leads to saline and alkaline condition. This results in loss of permeability, toxicity and anaerobic conditions. In salt affected soils plants face constraint to derive their nutrients at the required rate due to high soil moisture tension, which affects adversely the crop growth and productivity.

10.1 Causes of Salt Problems

The following are the reasons for causing the soils become saline or alkaline.
1. Rise in water table: A rise in water table and high evaporation and transpiration rates with poor drainage lead to build up dissolved salts.
2. Quality of irrigation water: Irrigation water contains the dissolved salts exceeding certain limit cause accumulation of salts in soil profile.

9.1 Introduction

Water is a precious commodity. Necessity of conservation of water supply is increasingly felt all over the world as the demand of it continues to increase when the sources of supply are increasingly scarce. The conveyance and proportional distribution of water is one of the most important part of any irrigation project. Water available in the stream, reservoirs or wells is carried to the field of use through canals. The economy of any irrigation project largely depends on how efficiently the water is being transported and distributed in respect to water losses and cost.

Water losses in irrigation channels are mainly due to evaporation from the water surface and seepage from the bed and side of the channels. Seepage losses some time become the single important factor which causes unavailability of water particularly in downstream of the channel in canal irrigation system and excess pumping of water in tube wells and river lift irrigation system.

Hydraulics of wells means the laws that are applicable to understand the flow of water through the formation and certain aquifer properties that determine the discharge of a well. Darcy’s law is used in studying groundwater flow though Darcy’s law is not valid under certain cases.

8.1  Water Bearing Formation

The earth’s crust is called the lithosphere which consists of hard rocks and disintegrated rock materials. The outer parts of the earth’s crust are porous and containing partially and fully filled up with water. The surface strata of the earth is partially filled with water and is called as zone of aeration and the zone below this which is completely filled with water is called the zone of saturation. The zone of aeration is divided into (i) the soil water zone (ii) the intermediate zone and (iii) the capillary fringe (Fig.8.1).

7.1 General

The major portion of water in a crop field gets lost through evaporation and transpiration. Evaporation is the process by which water is changed from the liquid state to vapor state. It takes place from the adjacent soil, water surface or from the surfaces of leaves of the plants. Transpiration is the removal of water vapour through plant body. Evapotranspiration(ET) is the sum of evaporation and transpiration. The process of evaporation and transpiration goes on simultaneously and difficult to separate them in a crop field.

The term consumptive use is used to refer evapotranspiration together with the water used in the metabolic activities of the crop plants. The actual amount of water used in metabolic activities is insignificant (less than 1% to ET). Therefore, the consumptive use and evapotranspiration are often used as synonymous term. It includes the water consumed by the plants

The plants collect water by its root system available in the soil medium. A soil rich in nutrients cannot ensure success of crops unless the presence of satisfactory state of water and air, mechanical attributes and thermal regime. The physical properties of soil and plants greatly influence the movement, retention and use of water. The soil should provide sufficient pore spaces and size distribution and decomposition of rocks and for the movement and retention of water for plant needs. Rainwater, irrigation, groundwater, seepage, etc., contribute in replenishing the water in dried up soils. In all the cases thorough understanding of behavior of water is required to ensure the need of water to plants and optimize the use of irrigation water.

6.1 Soils

Soil is initially formed by the disintegration and decomposition of rocks and minerals and accumulation of biological residues. Usually the outer layer of the land surface is referred

5.1 Irrigation Channels
Canal or channel is an artificially made conduit through which water is supplied to the field from river, tank, reservoir or wells. The open channel is the most common type of water conveyance system. If the pipes and drains are partially full behave like open channel. The irrigation channel may be lined or unlined and the flow is either uniform or varied.

The canal may be classified in following ways.

a) Classification based on the source of supply i) Permanent or perennial canal ii) Inundation canal

A canal is said to be permanent when it is fed by a permanent source of supply and has permanent networks of distribution of supplies. Inundation canals draw their supplies from river usually when water stage exceeds a predetermined level. Headworks are not provided for diversion of river water to canal. However, canal head regulators are provided to regulate the canal head as required time to time to accommodate the changing pattern of river course.

Scheduling irrigation is the process of determining when to irrigate and how much to irrigate. Selecting the appropriate time span in between two irrigation and applying the required volume of water in each irrigation, ensures saving of water, minimize energy use, higher crop yield and lower production costs. Irrigation applied earlier than due date causes loss of water through evaporation or deep percolation and later causes water stress to plants and thereby affects the growth and yield of the plants.

Scheduling of irrigation may be required in two field conditions: (i) when available of water is adequate, (ii) when availability of water is limited.

In the places where water is adequate scheduling of irrigation follows full   irrigation with time sequence of minimum number of irrigation to ensure maximum yield and high water use efficiency. When water is limited its use is rationalized by using at the sensitive stage

3.1 Introduction
Irrigation efficiency evaluates how effectively the water has been distributed for the purpose of crop production. Water is conveyed to crop field through canal water courses and channels. During this process considerable amounts of water get lost through run off, deep percolation, evaporation, etc. The losses of water greatly depend on the skill of the irrigator, degree of land preparation, and design and planning of the system. The extent of water losses starting to diversion of water from its source to crop field though conveyance and ultimate application and distribution of water in crop field which can be estimated separately. The estimation of these efficiencies enables one to identify the step(s) where improvement is required. The method of measurement and evaluation for its efficiency is prerequisite for proper use of water. Irrigation efficiency in developing countries in general is poor particularly in gravity irrigation methods. However, water is become more and more scarce. Due to pressing need of it judicious and efficient management is one of the vital issues to be solved on priority basis.

Measurement of water used in irrigation ensures the application of required amount of water in crops. Knowing the rate of flow the adjustment to period of control at gates, etc. can be done to regulate the water at different branches of canals. To get the total control over the supply of water there should have the provision of water measurement at the critical points in irrigation systems.

Units of Measurement

Water is measured at rest or in motion. The water of reservoir, ponds, tanks, etc. at rest is measured in volumetric unit as liter, cubic meter, hectare-meter and hectare-centimeter. Water flowing in rivers, canals, channel, etc. is measured in litre/sec , liter per hour, meter per sec and hectare-meter per hour or day.

1.1 Introduction
Irrigation is the artificial application of water needed to the crop field. It is the process of uniformly wetting the root zone depth. The wetting may be done over the land surface or below of it. The application of water in excess to the requirement or accumulation of water in crop field due to rain or unplanned seepage is not considered as irrigation. However, irrigation is supplemental to rainfall. Irrigation water is considered as single most important input for crop production.

Appendix - 1:
Physical Properties of Seed – bed / Puddled Soil

Tillage is the process of getting the soil ready for planting and maintaining it loose and weed-free while the crop is growing.  The main goal and core function of tillage are broken down into three phases:

1. Creating a suitable seedbed,
2.  Eliminating weed competition, and
3.  Enhancing the physical quality of the soil.

10.1. Acts, Policies and Schemes that Benefit Farmers
10.1.1. PM-KUSUM

As part of its Intended Nationally Determined Contributions (INDCs), India agreed to increase the installed capacity of electric power from non-fossil fuel sources to 40% by 2030. The Pradhan Mantri Kisan Urja Suraksha Evam Utthaan Mahabhiyan Scheme aims to ensure energy security for Indian farmers while also upholding this commitment. The PM-KUSUM Scheme was launched in 2019 with 3 components:

7.1. What is Energy Conservation?

In order to protect resources for future use and to lessen environmental degradation, energy conservation refers to actions performed to limit energy use.

.2. What is Energy Efficiency?

The definition of energy efficiency is the use of less energy to carry out a task or achieve a goal. Homes, buildings, and manufacturing facilities that use less energy to manufacture things require less energy to heat, cool, and operate appliances and electronics.

6.1. Calculation of Energy Requirements for Field Operations
The energy needs for a certain field activity can be determined by adding the amounts of human, bullock, mechanical, and/or electric energy consumed.

Operational Costs for Various Power Sources
Manual power

In the case of human labour, the wages of unskilled employment are charged on an hourly or daily basis (as determined by the location).In the case of research farms, the costs for operating a pair of bullocks are determined on the basis of the cost of a pair of bullocks, the salary of an operator, the cost of bullock feed, and any other expenditures (as imposed in a given location). For the farmer’s fields, however, the real hiring expenses are used as the foundation.

5.1. Introduction

The energy equivalent can be considered to be an alternate energy unit, precisely related to units such as the joule, calorie, or Btu. In energy talks, many units are employed. They are divided into two categories: (a) basic units and (b) source-based units.

Energy in Agricultural Context (FAO)

Agriculture’s fundamental and foremost function is to produce food and other primary products, so contributing to food and nutritional security. Sustainable Agriculture and Rural Development (SARD) attempts to promote ecologically non-degrading, technically suitable, commercially successful, and socially acceptable development in the agriculture, fishery and forestry sectors. Achieving food security necessitates policies that promote social, cultural, political, and economic stability. Integrating agriculture’s economic, social, and environmental roles can help to attain these objectives.

Agriculture may provide a variety of non-food commodities and services. This can include its application as a viable, long-term source of energy. According to the FAO, agricultural activities and related land use directly contribute to non-agricultural functions such as social, environmental, economic and cultural products and services. They can have major advantages or disadvantages. Research reveals that, in addition to food security, agriculture contributes significantly to attaining sustainability at the local, national and global levels in rural development, energy and the environment. The efficient operation of the market encourages the identification and strengthening of these many functions, as well as the development of new techniques and technologies. Plant and crop-based resources are utilised as raw materials in a wide range of industrial goods, including wood for paper and board production, starches for adhesives, and vegetable oils for paints and resins.

Introduction to Energy Sources

Consumption of nonrenewable energy sources has caused more environmental harm than any other human activity during the last century. Electricity generated from fossil fuels like coal and crude oil has resulted in excessive levels of hazardous gases in the environment. As a result, several issues exist now, such as ozone depletion and global warming. Vehicle pollution has also been a significant issue.

As a result, alternative energy sources have become increasingly vital and relevant in today’s society. These sources, such as the sun and wind, can never be depleted and are hence referred to as renewable. They produce fewer emissions and are readily available locally. Their application has the potential to significantly reduce chemical, radioactive, and thermal pollution. They stand out as a promising source of infinite clean energy. These are also known as non-conventional energy sources.

Energy is a critical component of the economic infrastructure, as it is the primary input required to support economic growth. Economic development and energy use have a close relationship. The higher a country’s per capita energy usage, the more developed it is and vice versa. Human civilization is dependent on several energy sources.

Observation recording: Students are advised to visit the nursey and forest plantation to record the various tending operations which are adopted by the forest department or Plantation Company.

Observation recording Lay the quadrats with the help of rope. Identify all the plant species, and count their number in each quadrat, dbh

Observation recording: To know the suitability of the tree species for plantation of various problematic areas, students are advised to visit the various nearby problematic sites or forest and record the naturally growing tree species.

Observation recording: Students are advised to visit the Safeda plantation for collection of stem cuttings then raised in polythene bags and record the various nursery practices and conduct tending operations in Mahogany plantation.

Observation recording: Students are advised to visit the Khair plantation for collection of stem cuttings then raised in polythene bags and record the various nursery practices and conduct tending operations in Khair plantation.

Observation recording: Students are advised to visit the Mahogany plantation for collection of seeds/stem cuttings then raised in polythene bags and record the various nursery practices and conduct tending operations in Mahogany plantation.

Observation recording: Poplar rarely raised by seeds. It is generally raised by stem cuttings. Students are advised to visit the Poplar plantation for collection of stem cuttings then raised in polythene bags and record the various nursery practices and conduct tending operations in Poplar plantation.

Observation recording: Students are advised to visit the Sandalwood plantation or forest for seed collection then sowing the seeds in nursery and record the various nursery practices and conduct tending operations in Sandal wood plantation.

Objective: To study the planting and stand management practices of Kala Shisham (Dalbergia latifolia).

Observation recording: Students are advised to visit the shisham plantation or forest for seed collection then sowing the seeds in nursery and record the various nursery practices and conduct tending operations in shisham plantation.

Observation recording: Students are advised to visit the teak forest or plantation for seed collection then sowing the seeds in nursery and record the various nursery practices and conduct tending operations in teak plantation.

Observation recording: The students are advised to visit the different forests areas and identify various insects and pests damaging trees in various ways like leaf feeding (defoliator), stem boring (stem borer) damaging seeds (seed borer) etc and various pathogens. Collect the specimens from field bring them in laboratory and identify with the help of inhouse specimens in college laboratory or standard literature viz. The Ecology and Control of the Forest Insects of India and the Neighbouring Countries by Beeson CEC, Forest Pathology: Principles and Practice in Forestry by Bakshi, BK.

Observation recording: The students are advised to visit the different forests areas and identify various insects and pests damaging trees in various ways like leaf feeding (defoliator), stem boring (stem borer) damaging seeds (seed borer) etc and various pathogens.

Observation recording: Now a days green felling is completely banned. Fuelwood species are managed under clear-felling systems and tree species infected by insects and pests are felled selectively. The students are advised to visit the fuelwood plantations and forests areas where selective felling is going on.

Observation recording: Today green felling is completely banned. Fuelwood species are managed under clear-felling systems and tree species infected by insects and pests are felled selectively. The students are advised to visit the fuelwood plantations and forests areas where selective felling is going on.

Objective: To study the seed germination, pollination and dispersal type of various temperate tree species.

Observation recording: To record the observation on seed germination, Pollination and dispersal needs to conduct frequent field visits in different seasons for recording the various pollination and dispersing agents and conducting experiment on seed germination.

Observation recording: To record the observation on seed germination, Pollination and dispersal needs to conduct frequent field visits in different seasons for recording the various pollination and dispersing agents and conducting experiment on seed germination.

Observation recording: To record the response of various tree species to produce root sucker, coppicing, pollarding, pruning and browsing of various tropical tree species requires field visits and conducting experiment to observe which species is producing root suckers, coppice etc.

Observation recording: To record the response of various tree species to the light, fire, drought, frost and wind, frequent visits of the forest areas which are affected by fire, drought and frost should be conducted. Studies relevant to light requirement in various growth stages of tree and ability to stand against various intensities wind are very lengthy that requires long time periodic studies.

Observation recording: To record the response of various tree species to the light, fire, drought, frost and wind, frequent visits of the forest areas which are affected by fire, drought and frost should be conducted. Studies relevant to light requirement in various growth stages of tree and ability to stand against various intensities wind are very lengthy that requires long time periodic studies.

Observation recording: Phenological events are typically quantified by observing the date of onset and the duration of particular phenophases, which include both vegetative and reproductive events like leaf shedding, leaf emergence, flowering and fruiting. To record the phenological events students should note down the emergence of leaf, flowering and fruiting at the interval of 15 days by vising the targeted tree species.

Observation recording: Phenological events are typically quantified by observing the date of onset and the duration of particular phenophases, which include both vegetative and reproductive events like leaf shedding, leaf emergence, flowering and fruiting. To record the phenological events students should note down the emergence of leaf, flowering and fruiting at the interval of 15 days by vising the targeted tree species.

Objective: To study the morphological description and field identification characteristics of various temperate tree species.

Observation recording: For correct identification of any temperate tree species, it is necessary to observe the type of bark, type of leaf, leaf arrangement and surface of leaf. For easy understanding of the students some examples are given in table:

Observation recording: For correct identification of any tropical tree species, it is necessary to observe the type of leaf, leaf arrangement, surface ornamentation of leaf and various types of margins. The type of leaf, margins and leaf arrangement can be seen without help of any lens whereas to observe the ornamentation a hand lens will be require.

Modern silvicultural tools involve in a paradigm shift from a highly manual to mechanize or digital data recording and tight operational control. Now a days many machines or digital tool are being used in silviculture like pitting machine, tree planter, Laser geo hypsometer, Satellite system etc.

Introduction

Animal behaviour is the study of how animals interact with one another, other living things, and their environment. Animals display a variety of behaviours in response to both external stimulus and their own pathophysiological state. Almost all domestic animals express a variety of behavioural responses throughout their lifespan, like feeding, sexual behaviours, etc. But every species responds to the same stimuli in a different way. This is why; the study of animal behaviour helps in efficient breeding, feeding, and reproductive management. It also serves as a reliable indicator of overall health and well-being.

Introduction

Climate change induces significant and long-lasting shifts in the statistical distribution of weather patterns over periods ranging from decades to million years. It is believed to be the cause of long-term temperature changes, changes in rainfall patterns and volume, prolonged summer seasons, increasing sea levels, and increased frequency and intensity of floods, droughts, and heat waves, etc.

Animals are intimately and inseparately associated with their physiological and chemical environments from conception until death. As a result, climate change has an impact on animals both directly and indirectly. Since, animals have had to alter their behavioural and physiological mechanisms in order to maintain homeostasis.

Climate change has emerged as a serious threat to the livestock industry. It reduces animal productivity by lowering growth, milk yield, meat production, egg production, wool production, reproductive performance, and health. About 20 to 30 percent of plant and animal species would likely be at risk of extinction with an increase of 1.5 to 2.5°C, which will result in severe consequences for food and nutritional security in developing countries. This is why; measurements of meteorological variables are needed for effective scientific management of livestock and poultry to cope with the negative impacts of climate change while enhancing growth and productivity.

Introduction

Growth is the irreversible gain in body weight, size, length, and circumference. It is accomplished by two fundamental processes: hypertrophy (increase in tissue, cell volume and progressive accumulation of intercellular substances) and hyperplasia (growth as a result of cellular multiplication by mitotic division). Animal growth is influenced by both genetic and environmental factors.

Animal body growth and weight gain play a critical role in reproductive performance. It also acts as one of the traits to evaluate the breeding value, optimize management & feeding practices, and prepare the correct dose of therapeutic pharmaceuticals to treat animal diseases. As a result, measurement of body growth is essential for the selection of superior germplasm, feeding & housing management, health care management, and optimizing other environmental conditions that have an impact on animal growth for an economically viable animal industry.