eChapters

R

Rabbet: A rectangular groove or cut made in the edge of a board, so that another similar cut may fit into it to form a rabbet joint.

Rack and pinion: A gear arrangement consisting of a toothed bar that meshes with a pinion. These are used to transform circular motion in to rectilinear motion and vice versa.

Rack and pinion steering: A steering system in which the rotation of pinion gear at the end of the steering column moves a toothed bar (the rack) left or right to transmit steering movements.

Radial arm: The movable cantilever, which supports the drilling saddle in a radial drilling machine.

Radial bearing: Bearing made with cylindrical or with barrel shaped rollers. The direction of action of the load transmitted to the axis of shaft.

Radial drill: l.A drilling machine in which the drill spindle can be moved along a horizontal arm, which itself can be rotated about a vertical pillar. 2. A heavy drilling machine, so constructed that the position of the drill can be adjusted to the work without moving the latter.

Radial engine: An engine, which has stationary cylinders, arranged radially around a common crankshaft.

SAE: Society of Automotive Engineers; used to indicate a grade or weight of oil measured according to the SAE.

Safe load: The load that a piece can support without exceeding the working unit stress.

Safety device: An installation designed to protect the operator or other persons. E.g., shields, grass-catching equipment, deflectors, covers for chains, belts, drive shafts, etc.

Safety factor: The degree of surplus strength over and above normal requirements, which serves as insurance against failure.

Safety hitch: A hitch incorporating a device to avoid breakage when an implement works against an abnormal resistance.

Safety valve: 1. An automatic valve, which opens and relieves the pressure when it reaches a predetermined value, thereby protecting the system and operator. 2. A safety device for allowing steam or water to escape from a boiler when the pressure may become dangerous. Usually adjusted to permit not more than 5 pounds of pressure above maximum allowable working pressure of the boiler.

T bolt: A bolt shaped like the letter “T, the head being a transverse piece, which fits into the recessed under cut T slots, as on a table of a milling machine or planning machine.

T head engine: A cross section of an engine block resembles the letter T. Valves are arranged on both sides of the engine; requiring two camshafts and two camshafts drive gears. An expensive type of construction.

Tachometer: An instrument for measuring the speeds of shafts in revolutions per minute.

Tail pulley: A pulley at the tail of the belt conveyor opposite the normal discharge end; may be drive pulley or an idler pulley.

Tail screw: The screw, which operates the spindle of the tailstock on a lathe.

Taillight: A signal light, required by law to be carried on the rear of every automobile, and lighted when the car is driven at night.

Tailstock: The movable head of a lathe as distinguished from the headstock, which is fixed.

Take up: A tensioning device in a belt conveyor system for taking up slack of loose parts.

U clamp: A clamp shaped like the letter ‘U’ used for clamping down work on planer beds.

Ultimate strength: The highest unit stress that can be sustained, this occurring just at or just before rupture in stress strain diagram.

Ultrasonic drilling: A vibration drilling method in which ultrasonic vibrations are generated by the compression and extension of a core of electrostatic or magneto static material in a rapidly alternating electric or magnetic field.

Ultrasonic machining: The removal of material by abrasive bombardment and crushing in which a flat-ended tool of soft alloy steel is made to vibrate at a frequency of about 20,000 Hz and an amplitude of 0.001-0.003 inch (0.0254-0.0762 millimeter) while a fine abrasive of silicon carbide, aluminum oxide, or boron carbide is carried by a liquid between tool and work.

Uniform: Implies no change with location over a specified region.

V belt: An endless power transmission belt with a trapezoidal cross section, which runs in a pulley with a V-shaped groove. The top surface of the belt approximately flush with to top of pulley. V belt transmits higher torque at less width and tension than a flat belt.

V blocks: Metal blocks cut ‘V’ shaped on one side to permit holding cylindrical work while machining or testing.

V type engine: An engine with cylinder blocks arranged in a ‘V’ shape. One crankshaft serves both banks of cylinders.

Vacuum: Negative gauge pressure, or a pressure less than atmospheric pressure. Vacuum can be measured in psi, but is usually measured in inches or millimeters of mercury (Hg); a reading of 30 in. Hg (762 mm Hg) would indicate a perfect vacuum.

Walking machine: A machine designed to carry its operator over various types of terrain; the operator sits on a platform carried on four mechanical legs, and movement of his arms control the front leg of the machine while movement of his legs control the rear legs of the machine.

Wane: Wane is a defect in a timber or plank.

Washer: A small, flat, perforated disk, used to secure the tightness of a joint, screw, etc.

Washer cutter: A device having a fixed center and either one or two adjustable cutting points for cutting washers from leather, rubber, etc.

Waste heat: Energy, that must be dissipated to the atmosphere from a process such as the heat transferred from condensing steam in the condenser of a steam power plant.

Waste spark system: An ignition system, that energizes the spark each time the piston is at top dead center whether or not the piston is on the compression stroke or on its exhaust stroke. For hydrogen engines, the waste sparks are a source of pre-ignition.

Water (H₂O): 1. A colorless, transparent, odorless, tasteless liquid byproduct of the combining of hydrogen and oxygen, 2. The liquid form of steam and ice. Fresh water at atmospheric pressure is used as a standard for describing the relative density of liquids, the standard for liquid capacity, and the standard for fluid flow. 3. The melting and boiling points of water are the basis for the Celsius temperature system. 4. Water is the only substance that expands on freezing as well as by heating, and has a maximum density at 4°C.

X engine: An in line engine with the cylinder block so arranged around the crankshaft that they resemble the letter X when the engine is viewed from the end.

Alpinia is an important tropical ornamental crop valued for its attractive flowers and foliage and its potential as a cut flower and cut-green crop. This chapter introduces the botanical characteristics, species and commercially useful types of Alpinia. It discusses climate, soil, propagation, planting, nutrient management, irrigation, cultural operations, pest and disease management, harvesting and postharvest handling. Attention is given to maintaining quality stems and extending vase life for commercial markets. The chapter provides practical information for growers interested in producing Alpinia under suitable tropical and subtropical conditions and highlights its role in diversifying commercial floriculture enterprises. as a high-value ornamental crop.

Alstroemeria, commonly associated with Peruvian lily, is a valuable commercial cut flower appreciated for its attractive colours, long stems and excellent vase life. This chapter discusses its origin, distribution, genetics, botanical characteristics and commercially important cultivars. Production aspects include climate and soil requirements, propagation through rhizomes, planting, irrigation, nutrition, crop management and greenhouse production. The chapter also explains physiological problems such as flower abortion, pest and disease management, harvesting, postharvest treatment, grading and yield. Particular emphasis is placed on commercial-quality stems and management practices required to achieve consistent production under protected conditions.

This chapter introduces Alstroemeria as a high-value cut flower commonly known as Peruvian lily. It discusses its origin, distribution, genetics, botanical characteristics, commercial varieties and protected cultivation requirements. Temperature, humidity, light, carbon dioxide, irrigation, nutrition, crop management, harvesting and postharvest handling are addressed. The chapter also considers grading standards, vase-life enhancement and important pests and diseases. Particular attention is given to modern hybrids and greenhouse production for high-quality stems.

Introduction

Plant pathogens include fungi, bacteria, viruses, viroids, phytoplasma, and nematodes.

They have evolved different strategies for invading, feeding on, and reproducing inside plants.

Biotrophic pathogens require living tissue to grow and reproduce.

Necrotic pathogens kill host tissue at the onset of infection and feed on the dead tissue.

Viruses generally require living tissue for survival.

Alternate bearing or biennial bearing is a term used in fruit crops to refers to trees that have an irregular crop load from year to year. It is a major problem in some of the fruit crops. Long term studies of flower and fruit production in some of the fruit crops demonstrated that the majority of shoots on a tree bear flowers and then fruits in one year, i.e. a greater than average crop and the next year most of the shoots will produce only leaves resulting in a smaller than average crop.Thus, it is characterized by heavy crop load in trees i.e. on year, followed by a light or no subsequent crop load i.e. off year. When on and off year sequence does not follow a systematic pattern it is called periodicity of cropping or irregular bearing. Phenomenon of alternation is more prominent in the perennial fruit crops particularly Anacardiaceae (mango, Pistachionut), Carylaceae (hazelnut), Oleaceae (Olives), Rosaceae (apple, Pear, Plum, Apricot, etc.), Rutaceae (orange, tangor, satsuma, etc.) and also in tamarind, Jamun etc.

Many horticulture schemes have been launched by the Government. The main aim is to expand the area under horticulture with better productivity. These ambitious schemes are as follows.

A. Mission for Integrated Development of Horticulture (MIDH): Mission for Integrated Development of Horticulture (MIDH) is a centrally sponsored scheme from 1st April 2014 for the holistic growth of the horticulture sector covering fruits, vegetables, root and tuber crops, mushrooms, spices, flowers, aromatic plants, coconut, cashew, cocoa and bamboo. Under MIDH, Government of India (GOI) contributes 60% of total outlay for developmental programmes in all the states except states in North East and Himalayas, 40% share is contributed by state governments.

Amino acids are organic molecules made up of carbon (C), hydrogen (H), oxygen (O), and nitrogen (N). However, sulfur (S) and selenium (Se) are also found in some cases. Amino acids are essential organic compounds that come together to create proteins, thus making them the fundamental building blocks of proteins. These biomolecules play vital roles in various biological and chemical processes within the human body and are essential for the growth and development of an individual.

Amino acids consist of an acidic group (-COOH), a basic group (-NH2 ), and a side chain (R) or a hydrogen (H) atom, all bonded to the carbon atom. The features of amino acids are due to the side chain because they differ only in their side chain. All amino acids have the same basic structure except proline, which has a cyclic structure.

Various forms of amino acids like alpha (α), beta (β), gamma (γ) or delta (σ) form are found. The position of the amino group (-NH2 ) determines the form of the amino acid, i.e., if the NH2 group is attached to the α-carbon, it is called α-amino acid; if β-carbon, it is called β-amino acid, and so on. Mostly, α-Amino acids are found as the numbering of amino acids is done from the carboxylic group (-COOH).

Introduction

Present work report the study on Jakekur dam situated 4 km. from Omerga

The degradation of dam has occurred not only due to influents inflow but also by sanitation, domestic sewage, agricultural waste, and other activities around the dam like washing cloths, cattle, vehicles, and dumping of solid waste. Apart from it a large number of heavy metals is contributed by corrosion of metal pipe, runoff water from surrounding area during rainy season discharge of decorative paints in water bodies.

Geographical and morphological features of Jakekur dam.

Catchments area : 2110 hector

Gross storage : 10.17 TM C

Full reservoir level : 10 meter.

Length of the dam : 21.25 km.

Height of the dam : 14.80 meter.

Taxonomic Classification of Common Livestock Species

A series of terms (kingdom, phylum, class, order, family, genus, species etc) is used to denote the member of a kingdom and each division of the hierarchy contains one or more groups from the next lower division like subphyla, subclasses, suborders, subfamilies, or subgenera etc if required. Further, species may be subdivided into varieties, breeds, or strains. Domestic farm animals belong to either class Mammalia or Aves. The scientific name of an animal comprise of its genus and species names. The first letter of genus name is written in capital letter but not the species name. While writing the scientific name of an animal the genus and species names are underlined when handwritten and always italicized when printed. General characteristics and taxonomic arrangements of common domestic animals have been given below.

Kingdom : Animalia

Members of kingdom Animalia are multicellular, eukaryotic heterotrophs. Adult animals develop from embryos. Most animals ingest and digest their food in some kind of internal cavity.

This chapter introduces the fundamental concepts and processes that determine the structure and functioning of forest ecosystems. It examines forest ecosystem structure, different forest ecosystem types, community ecology, succession, population ecology, energy flow, and nutrient cycling. The chapter also addresses forest soil ecology, biodiversity, disturbances, climate change, and restoration ecology. Modern tools and sustainable forest management approaches are included to connect ecological principles with practical forest management. By integrating ecosystem processes with conservation and management perspectives, the chapter provides a foundation for understanding forest dynamics and maintaining healthy and resilient forest ecosystems.

1.1 Introduction

Irrespective of caste, creed, culture, sex, age or religion people like garden. A well-maintained garden serves as lungs of the city or locality as it is a prime source of plenty of oxygen and people enjoy the surrounding and feel happy by fresh air. In holy books of Hindu religion, the importance of plants as well as gardens are explained very beautifully. In the holy Bible it is mentioned that Adam and eve lived in garden. In Quran it is explained as the paradise on earth. So, scriptures of all religions explain about gardens. It shows gardens and plants are closely related to human from the origin of human belief.

1.1 Introduction

Fruit breeding is an ancient technology with dynamic current technology and an exciting future (Janick and Moore 1975, 1996). In its broadest sense, fruit breeding refers to the purposeful genetic improvement of fruit crops through various techniques including selection, hybridization, mutation induction and molecular techniques. Its origins trace to the domestication process in prehistory and antiquity, where useful species were chosen and cultivated, and improved by continuous selection (Janick 2005, 2011). Through the millennia genetic improvement of these species have been achieved by grower selection, first from natural seedling populations and then from grower field that continued unique genotypes fixed by vegetative propagation. Spontaneous hybridization between wild plants and cultivated clones was critical to the early domestication of fruits.

Analytical testing provides objective evidence of the composition, safety, physical structure, and sensory quality of ice cream. This chapter introduces the major analytical approaches used in industrial ice cream manufacturing, including chemical, physical, microbiological, and sensory evaluation. Important parameters such as fat, milk solids-not-fat, protein, sugars, ash, acidity, pH, overrun, meltdown, fat destabilization, texture, and product weight are discussed. The chapter explains how different tests support routine quality control, product development, troubleshooting, research, regulatory compliance, and shelf-life studies. It emphasizes that no single analytical parameter can define overall quality. Effective product evaluation requires integrated interpretation of chemical, physical, sensory, microbiological, and storage data.