eChapters

22.1. What?

Threshing is the process of separating grains from the straw or pod by impact, friction or both. Threshing should be done at an appropriate time after harvest. Delayed threshing causes rapid deterioration of the grains, especially during field drying or when the crop is stacked in the field. Improper threshing leads to wastage of grains and reduces the quantity of final marketable produce. After threshing, the produce has to be winnowed to remove lighter materials such as unfilled grains, chaff, weed seeds and straw using a blower, air fan or wind. Winnowing improves the ability of the grain to be safely stored, milling output and quality.

22.2. Methods employed

Traditionally, threshing is done by beating the harvested crop on a threshing floor directly or with a stick. Another traditional method of threshing is to make a bull walk in circles on the grain on a hard surface. In some areas, the harvested panicle with grain is spread on the surface of a country road so that the grain may be threshed by the wheels of passing vehicles. In these methods winnowing is separately performed. However, with the development of technology, now it is mostly done by machine referred to as threshers, shellers and stripper. Some of these threshers have inbuilt facility for threshing. Thus, threshing and winnowing are completed in a single process.

It is a mechanical manipulation of soil to provide favourable condition for crop production. Soil tillage consists of breaking the compact surface of earth to a certain depth and to loosen the soil mass, so as to enable the roots of the crops to penetrate and spread into the soil.

Tillage operations following primary tillage which are performed to create proper soil tilth for seeding and planting are secondary tillage. These are lighter and finer operations, performed on the soil after primary tillage operations. Secondary tillage consists of conditioning the soil to meet the different tillage objectives of the farm. These operations consume less power per unit area compared to primary tillage operations. Secondary tillage implements may be tractor drawn or bullock drawn implements.

Tillage is a common agricultural practice that involves preparing the soil for planting crops. It is the manipulation of soil to create a suitable seedbed, manage weeds, and improve soil structure for optimal crop growth. Tillage methods can vary widely and are often classified into different types based on their intensity and purpose. Here are some common types of tillage:

1. Conventional Tillage: This is the most intensive form of tillage and involves turning over the soil completely, often using a plow. It disrupts the natural soil structure and exposes the soil to erosion but can effectively control weeds and prepare a clean seedbed.

2. Reduced Tillage: Also known as conservation tillage, this method aims to disturb the soil as little as possible. It typically involves minimal or no plowing and relies on techniques like no-till, strip-till, or zone-till. Reduced tillage helps to maintain soil structure and reduce erosion while conserving moisture.

3. No-Till: In this approach, the soil is left undisturbed, with crop residues from previous harvests left on the field surface. A planter creates small openings in the soil for seeds. No-till farming helps retain moisture, reduce erosion, and maintain soil health. It is widely adopted for its conservation benefits.

Duration: 60-75 minutes
Objective: Master techniques to prioritize tasks, meet deadlines, and reduce stress for improved productivity and work-life balance.
Why It Matters
Effective time management ensures focus on high-impact tasks, reduces procrastination, and prevents burnout. Poor time management leads to missed deadlines, stress, and lower quality work. For example, spending hours on emails instead of strategic planning can derail priorities. This module provides tools to optimize time usage.
Learning Outcomes: By the end of this module, participants will:
1. Understand prioritization and planning techniques (e.g., Eisenhower Matrix, Pomodoro).
2. Practice strategies to minimize distractions and delegate effectively.
3. Create a personalized time management plan.

8.1. Vegetables

8.1.1. Tomato (Lycopsarsicon Esculentum)

Temperature: A warm climate crop can tolerate high temperature but cannot withstand frost. Minimum temperature for germination of seed is 8 to 10°C. Night temperature for fruit setting is 12 to 22°C. Critical night temperature for fruit setting is below 12°C. Critical day temperature for fruit setting is above 32°C. If the greenhouse can maintain the temperature as mentioned above then the non-terminal or indeterminate tomato crop can be grown for 10 to 12 month duration.

Variety: Indeterminate (producing flowers and fruits continuously along the stem as it grows) hybrid varieties resistant to nematodes or fusarium or verticilium wilt disease may be selected.

2.1. Biotechnology institutes

Regional office of ICGEB (International Centre for Genetic Engineering and Biotechnology) at New Delhi (Headquarters at Trieste, Italy established in 1983).

Lal Bahadhur Shastri Centre for Advanced Research in Biotechnology at IARI, New Delhi

National Institute of Animal Biotechnology, Hyderabad

Aim: To study the effect of variation of field current upon the stator current and power factor with synchronous motor running at no-load, hence to draw V and inverted V curves of the motor.

With constant mechanical load on the synchronous motor, the variation of field current changes the armature current drawn by the motor and also its operating power factor. As such, the behavior of the synchronous motor is described below under three different modes of field excitation.

Scientific research is always based on observable and measurable facts. This applies to physical as well as humanitarian fields of science. In order to investigate social or psychological phenomenon, most of the times we need quantified information related to the phenomenon under investigation. In order to secure this data, we need one or more method/ means of collecting observable/measurable data.

In this chapter we will talk about the tools which are required to make project in artificial intelligence. All this bellow discussed tools are uses python programming language for making any project in any respective field. We have discussed about how anyone can install and use the tools to built a real time project in artificial Intelligence.

Using Python IDE

To download and install Python visit the official website of Python https://www.python.org/downloads/and choose your version. We have chosen Python version as per requirement all the codes in this book were on python version 3.6 as you can see in the Fig. 7.1.

Efficient horticultural production depends greatly on appropriate tools, implements, and timely cultural operations. This chapter introduces the major equipment used for land preparation, planting, weeding, pruning, propagation, irrigation, harvesting, and routine crop management. It emphasizes correct tool selection according to crop, operation, plant structure, and working conditions. Digging tools, secateurs, loppers, pruning saws, grafting knives, and other specialized implements are discussed along with principles of maintenance, sharpening, sterilization, and safe handling. The chapter also explains important cultural operations that influence crop establishment and productivity. Proper use of tools improves precision, reduces labour, prevents plant injury, and increases operational efficiency in horticultural systems.

1. Tyson Foods Inc. 
2210 W. Oaklawn Drive, Springdale, AR 72762-6999 
Phone  : 479-290-4000; Fax  : 479-290-4061; Web site  : www.tyson.com

Executives : Chairman : John Tyson; Pres./CEO : Richard Bond; SVP-Intl. Ops. : Mike Baker; SVP-Commodity Trading & Risk Management : Jean Mrha Beach; Group VP-Research & Development, Logistics & Tech Services : Hal Carper; SVP & CIO : Gary Cooper; Group VP & International Pres. : Rick Greubel Jr.; SVP, Controller & CAO : Craig Hart; VP, Assoc. General Counsel & Secretary : R. Read Hudson; Group VP-Ops : Donnie King; SVP-Human Resources : Ken Kimbro; EVP & CFO : Dennis Leatherby; Group VP-Food Service : Bernard Leonard; Sr. Group VP-Fresh Meats : James Lochner; SVP-External Relations : Archie Shaffer III; Group VP-Consumer Prods : Donnie Smith; EVP & General Counsel : David Van Bebber; SVP-Renewable Products : Jeff Webster; VP-Investor Relations & Asst. Secretary : Ruth Ann Wisener

Fundamentally toposheet represents a kind of map in which topographic features of particular area is given details on the map features in two dimensional land surfaces. It shows both horizontal and vertical portion of the terrain with a combination of contour lines, contours, symbols, labels and related representation together in one piece of paper. Toposheet portray the shapes, location of mountains, many natural and manmade features, and the toposheet combinedly uses for extracting accurate information about particular area containing land surface features.

6.1 Introduction

Torrefaction is a thermophilic process of biomass conversion into a solid, friable, homogenous coal-like material, which has better fuel characteristics than the original biomass. Torrefaction involves the heating of biomass material in the absence of air at 250 to 300°C temperature. Torrefaction produces high-grade hydrophobic nature solid biofuels from various streams of woody biomass or agro residues.Torrefied biomass has high energy density then the original biomass which make torrefied biomass as renewable alternate source for power generation in coal power plant. Torrefied biomass being hydrophobic in nature can be stored easily for longer duration with negligible biological degradation. At 250-300°C temperature volatilization has been taking place and around 30% mass of the biomass is reduced as compared to original untorrefied biomass with net energy loss of approximately around 10%.The end product is a predictable, homogeneous, hydrophobic, high value solid biofuel with far higher energy density and calorific value than the original biomass feedstock. During the torrefaction process a combustible gas is released, which can also utilised to provide heat to the process. The process diagram of torrefaction process is shown in Fig. 6.1.

Hardness is the total soluble Ca and Mg Salts (in same cases Fe salts). It includes sulphates and chlorides along with carbonate, bicarbonate and hydroxide salts. Soft water: 0-100 mg/L, Hard water: 100 - 300 mg/L, Very hard water: > 300 mg/L CaCO3. Total hardness should be 50- 300 mg/L. Very hard water causes osmoregulatory stress to fish. Hardness below 50 mg/L reduces growth of plankton.
Reagents
1. 10.01M EDTA solution: Dissolve 3.72 g disodium salt of EDTA in distilled water and make the volume 1L by shaking.
2. Eriochrome Black T (EBT) Indicator: Add 0.2 g dry Eriochrome powder to 50 ml of triethyl amine. Add 5 ml absolute alcohol and shake it.
3. Ammonium chloride-Ammonium hydroxide buffer solution: Dissolve 17.5g ammonium chloride (NH4Cl) in 142 ml of ammonia solution (NH4OH). Add distilled water to make the volume 250 ml.
Procedure
1. Take 50ml water sample in a 250 ml conical flask.
2. Add 2 ml buffer solution and 5 drops of EBT indicator.
3. Wine-red colour will appear.
4. Titrate against 0.01M EDTA till the colour changes into bright greenish blue.

Phosphorus is nearly exclusive found as phosphates in waters and wastewater and it categorised in to: a) orthophosphate, (b) organically bound phosphate and (c) condensed phosphates. Theses all three forms of phosphorus occur in solution, in the body of aquatic organisms through food chain. All the forms of phosphorous, whether dissolved or particulate are converted to inorganic forms (phosphate) after digestion of sample. Various methods use for the digestion of the sample including use of perchloric acid, H2SO4- K2SO4, H2SO4- HNO3 etc. The H2SO4- HNO3 digestion technique is discussed here.
Reagents
1. Phenolphthalein indicator
2. Conc. sulphuric acid (H2SO4)
3. Conc. nitric acid (HNO3)
4. Sodium hydroxide (NaOH), 1 N: Dissolve take 40 g of NaOH in 1000 ml of distilled water
Procedure
Digestion
1. Take 50 ml of sample in a Kjeldahl flask
2. Add 1 ml H2SO4 and 5 ml HNO3
3. Once the HNO completely removed, digest the sample on a hot plate until the volume approaches 5 ml. Then, keep heating the solution until it loses colour (you may also heat it in a beaker covered with a watch glass to prevent excessive evaporation).

The total plate count (TPC) is also called the Bacterial plate count (BPC), aerobic plate count, standard plate count (SPC), total viable count (TVC) or mesophilic count represents the number of colony forming units (CFU) per g (or per mL) of growing microorganisms such as bacteria, yeast and mold on a nonspecific solid bacteriological growth medium under the specified conditions. Temperature, incubating time, medium type, and any other conditions used in the enumeration varies upon reference standards and laboratory objectives. Laboratories participating in the program choose their own routine conditions.
Principle
Usually direct count of too many bacteria in a sample is difficult but the bacterial colonies may be used as a measure of the bacterial cells in the known serially dilution and plated out on an agar surface in such a way that single isolated bacteria form visible isolated colonies. However, colony-forming unit might actually consist of a chain of bacteria rather than a single bacterium if the organism often develops various cell configurations, such chains. Furthermore, a portion of the bacteria might be grouped together. Thus, typically refer to the process of using the plate count technique as a means of estimating the number of colony forming units (CFUs) in that known solution. Then further this figure use to extrapolate the total amount of CFUs present in the original sample.

Abstract
 
The definition of quality is described from a very simpler one “fitness for purpose or use” to a comprehensive “the totality of features and characteristics of a product or service that bear on its ability to satisfy stated or implied needs”. The concept of total quality management in food industry is adopted recently and it is the “integrated organization approach in delighting customer (both external and internal) by meeting their expectations on a continuous basis through everyone involved with the organization working on continuous improvement in all products/processes along with proper problem solving methodology”. TQM is concerned with the integration of all the efforts in organization towards quality improvement, quality development and quality maintenance to meet full customer satisfaction at economic levels. TQM enhances the work culture and employee’s satisfaction through participation and involvement and consequently the image of the organization.

Principle
The estimation of all solids, including dissolved, volatile, and suspended solids, is called total solids (TS). The residue that remains after the unfiltered sample evaporates between 103 and 105°C can be used to estimate total solids. Total dissolved solids (TDS) and Total suspended solids (TSS) are its two constituent components. After heating to 550°C, each fraction is separated once more into fixed solids and volatile suspended solids (VSS). The percentage of ash that remains is called fixed solids, while VSS is the organic proportion that was lost as CO2.
Apparatus
1. Ceramic or platinum evaporating dishes 100 mL volume.
2. Dessicator contain CuSO4.5H2O. Desiccator, provided with a desiccant containing a colour indicator of moisture (CuSO4.5H2O).
3. Analytical balance
4. Hot air oven
Procedure
1. Take a clean evaporating beaker or dish of required volume and dry it at hot air oven at 103 to 105oC for 1h, then cool and store it in a desiccator until needed. Immediately weigh before use. Note » the initial weight (Wi) in mg.
2. Take 250-300 ml or required volume of unfiltered well mixed sample in it (beaker or dish).
3. Place it in hot air oven at 103 to 105 oC for 2 h.
4. Cool it in a desiccator and take the final weight (Wf) in mg.
5. Replication the above process until a constant weight is achieved

In 1920, although electric vehicles were not used on the American farms about 5,000 electric industrial trucks were produced by 12 American manufacturers, while estimates of the total fleet ranged from 6,000 to 15,000, most of them built during the war. Most used an exchange charging system. Among the manufacturers seen in and around cities and towns were the Commercial Truck Company, the Lansden Company, the Walker Vehicle Company (now owned by Commonwealth Edison), the Ward Motor Vehicle Company, the Steinmetz Electric Motor Corporation, Walter Motor Truck Company, and the Baker R L Corporation.One step away from agriculture, Charles A. Ward of New York City, was head of his family’s baking company, made up of the Mackey Company, the Ward Corby Company, the Ward Bread Companyand the Ohio Baking Company of Cleveland. In 1911, Ward had decided to replace his horse-drawn delivery vehicles with electric trucks, thus doing away with the unsanitary stable hitherto part of or adjacent to bakery.¹

Alongside this, the challenge of using stationary electric agricultural machines continued to be met. Two innovations which entered into dairy farming were the milk cream electric centrifugal separator and the surge milker. The Babson brothers (Henry, Fred and Gus) of Chicago were friends of and dealers for electrical battery inventor and entrepreneur Thomas Edison, and importers of Belgian-made Méllote separators. In 1916, the Babsonsproduced their own Pine Tree milking machine. While the overall design was similar to others, the electrically powered Pine Tree Pulsator outperformed any other pulsator made. These machines were powered by a 32-volt Delco system with 12 batteries near the barn. Pine Tree Pulsators were simple enough that the farmer could maintain them himself. The Pine Tree Pulsator was patented in 1921. The problem with this unit was that it was difficult to keep clean.

Q. 1 Improper wheel balancing results in :-
(A) Excessive tyre pressure       (B) Excessive tyre speed
(C) Excessive tyre wear             (D) All above