eChapters

Abstract

The frictional properties such as coefficient of friction and angle of repose are very important in designing of storage bins, hoppers, chutes, conveyors, harvesters and threshers etc. Angle of repose is the angle made with the horizontal at which the material will stand when piled. The angle of repose is also important in designing the equipment for mass flow and structures for storage. The static angle of repose (b) was determined using an open-ended cylinder of 150 mm diameter and 250 mm height. The higher the moisture content, the higher the cohesion between the seeds. In terms of flow ability, the seeds are heavier and the inertia to move is increased. Coefficient of internal friction is the frictional resistance of seeds with each other. Coefficient of external friction is the frictional resistance between the seeds and the surface. The rolling resistance is directly proportional to the weight of the rolling object and to the coefficient of rolling resistance which is dependent on the rigidity of the supporting surface and indirectly proportional to the effective radius of the rolling object. The air velocity at which an object remains in a suspended state in a vertical pipe under the action of the air current is called terminal velocity of the object.

Cereal Processing

    1.    The protein content of wheat grain varies widely, but for bread making a value of at least 11% is required.

    2.    Low grain sulphur will result in low concentrations of the sulphur-containing amino acids, cystine and methionine, and may result in poor loaf volume.

    3.    During seed germination endosperm starch is converted into soluble glucose and maltose to support the developing embryo. This is brought about by enzymatic activity, especially the enzyme a-amylase.

    4.    Excessive a-amylase levels result in the formation of a darkened loaf crust as a result of sugar caramelization and a sticky crumb structure which can cause problems during slicing.

    5.    Wheat with a protein level below 10% is preferred to reduce gluten elasticity.

    6.    There is a very good correlation between grain nitrogen and the amount of malt extract achieved, low grain nitrogen giving more fermentable extract

    7.    The term ‘coarse grains milling’ is a very broad one that refers to the comminution of the berries of the wheat, barley and other coarse grain crops.

Abstract

The strenuous field trekking, inaccessibility, perception of geology only within the visibility range of the eyes etc. have remained matters of major constraints in the past in field based geological mapping. The remote sensing technology not only eradicated these but also provided lot many newer vistas in the field of geology. In addition, the application of such unique technology has brought out a hierarchy of newer concepts in the field of geology. The paper narrates the newer knowledge gathered on the geology of South India in the post remote sensing Era.

Abstract

As the available surface water is too inadequate to fulfill the man’s requirements he was forced to locate newer groundwater reservoirs on one side and to control the fast depleting water table on the other side. As the ancient techniques have failed to give precise models on groundwater targeting, he was to invent and employ newer technologies. Under this scenario the recently invented spatial technology has emerged as a very powerful tool in groundwater targeting and management. The vistas and virtues of such spatial technology in groundwater management have been discussed in this overview paper by citing some case studies from Tamil Nadu, India.

Technical and Economic Challenges in Advanced Packaging The implementation of advanced packaging technologies comes with a range of challenges. Technically, developing materials that are both highly effective and environmentally friendly is a complex task. Packaging must not only protect products and ensure their safety, but also minimize its ecological footprint. From an economic perspective, these advanced solutions tend to be more expensive, which can make it difficult for smaller businesses or those in cost-sensitive markets to adopt them on a large scale. Furthermore, the need for efficient production methods, scalable new materials, and affordable solutions continues to be a significant hurdle for the industry. Balancing Performance with Environmental Goals One of the primary challenges in packaging is achieving

13.1 Challenges in the technology transfer process
Technology transfer (TT) is more complex and involves the complex interrelationships between universities, research institutes, the private sector, the state, and society. Though TT is all about translating research findings into purposeful solutions that can support the economy and society, it is not a linear process. The challenges can be described as legal, institutional, cultural, financial, policy, and human resource. All this is accompanied by bottlenecks that inhibit or decelerate the diffusion of promising technologies.
13.1.1 Legal and intellectual property challenges
The vital component of technology transfer is the proper management of intellectual property (IP), which is often the most challenging aspect.
• Ambiguities in IP ownership: During multi-institutional or shared funder research, ownership is quite controversial. As an example, when a government lab and a university collaborate on the project, there is ambiguity as to who would have the ultimate licensing authority over the technology: the university, the lab, or the funding agency. This kind of fight hinders commercialisation and scares off industry partners.
• Lengthy patent filing and prosecution timelines: In several jurisdictions, the filings, examination, and granting of a patent may take between three and five years or more. Such delay is not compatible with the rapid cycle of invention in other fields such as ICT or biotechnology, where patent claims may become invalid before they are granted.
• High costs of IP protection: International direct patenting, like under the Patent Cooperation Treaty (PCT), is costly and involves legal services, fees, and upkeep costs. These costs are excessively high, which cannot be easily compensated by universities and startups, and where technologies are not secured or limited to local markets.

Definitions: Before starting the chapter, it is better to understand the basic definitions of the terms commonly used in this chapter.

Waste: Waste is any material or object which is discarded after its primary use by its holder. A holder means the person who produces and keeps the waste. 

ABSTRACT

World is suffering from coronavirus infection since the end of 2019. Corona virus disease spraying rapidly throughout the world from the beginning of 2020, for that cause it is declared as pandemic by WHO in march 2020. As no proper remedy found for this particular new disease till the date it is become oblivious to maintain social distancing and lock down. Due to the situation each and every sector including the education system totally stopped from March 2020. But we have to maintain the flow of education. Many of the educational institution of India promoted e learning for their students. To avoid coronavirus infection social contact as well as to carry out classes in regular manner, it is become necessary to promote e learning everywhere. But in India the situation is different because Steel we are a poor country where a good number of people do not have a smart phone even. There are many challenges in promotion of e-Learning during this coronavirus pandemic situation in India. In present paper we are going to discuss about some challenges in promotion of e-learning due to coronavirus pandemic situation.

Channel improvement increases or restores the ability of a river or drainage channel to convey floodwater safely. Natural or artificial channels may lose capacity because of sediment deposition, vegetation, debris, bank encroachment, irregular alignment, insufficient cross-sectional area, or excessive hydraulic resistance. Improvement can involve widening, deepening, straightening, clearing, lining, dredging, bank stabilization, or constructing additional waterways. This chapter discusses the purposes, advantages, disadvantages, and planning principles of channel improvement. It examines channel geometry, flow resistance, permissible velocity, sediment behaviour, erosion protection, and maintenance. The chapter also emphasizes that interventions must be evaluated carefully because poorly planned modifications can accelerate flow, destabilize banks, damage habitats, or shift flooding downstream.

So far much have been talked about the best hydraulic sections, as these appeared to be most economical sections. But as it appears may not be always true and there are exceptions to each individual site conditions.

9.1 Suitable and Economical Cross Section

Best hydraulic sections are most economical in lined and unlined canals. In lined canal this section is economical as long as the cost of earth work (excavation and embankment) is less than the cost of lining per unit length of channel and this is the most usual case. These sections, besides having least area and perimeter also have minimum top width. Therefore land width required is also minimum, in comparison to other wide sections. But if the cost of earth work / excavation is more, such as in rocks, or in very heavy cutting/filling, best hydraulic section do not remain most economical, and recourse to alternative section must be worked out.

Even in unlined channels in deep excavation or in deep filling recourse must be taken to narrower and deeper sections as far as possible.

Also the type of lining in the bed may be cheaper than the lining on sides and in such cases, lining of best section is no more most economical and cost economics of various alternatives including increase in bed width has to be worked out, see para 4.1 and 6.3.

2.1 Definition and Boundaries of Watershed Areas

Concept of Watershed Boundaries

The concept of watershed boundaries is fundamental to understanding the hydrological and ecological dynamics of a given landscape. Watershed boundaries, also known as drainage divides or catchment areas, delineate the geographical extent of a watershed, which is an area of land where all the water drains to a common outlet, such as a stream, river, lake, or ocean. Watershed boundaries represent the natural hydrological and ecological units of a landscape, reflecting the interconnectedness of water resources and ecosystems. Understanding the factors influencing their definition is essential for effective watershed management, resource planning, and environmental conservation. Exploring the delineation of watershed boundaries involves considering various factors that influence their definition:

a. Topography: Topography, particularly the elevation and slope of the land, plays a significant role in defining watershed boundaries. Watershed boundaries typically follow ridgelines or high points in the landscape, where water flows in different directions, ultimately converging into distinct drainage networks.

b. Hydrology: Hydrological characteristics, such as precipitation patterns, surface runoff, and groundwater flow, influence the delineation of watershed boundaries. Areas with higher rainfall or snowmelt may have larger watersheds with more extensive drainage areas, while areas with low precipitation may have smaller, more localized watersheds.

Proximate Analysis of Biomass
Objective
To determine the key compositional parameters of biomass, including moisture content, volatile matter, ash content, and fixed carbon, using standardized analytical procedures.
Principle
Proximate analysis of biomass is a standardized method used to determine the basic compositional components of biomass materials. It provides essential information about fuel quality and conversion characteristics. Biomass can serve as an energy source either directly through combustion or indirectly through conversion into gaseous, liquid, or solid fuels for more efficient utilization. These transformations occur through thermochemical processes (combustion, gasification, and pyrolysis) and biochemical processes (anaerobic digestion and fermentation).
Common biomass materials such as agricultural residues, cattle dung, poultry litter, and paddy straw are analyzed for parameters including total solids (TS), volatile solids (VS), ash content, total organic carbon (TOC), moisture content, and total sugars. These parameters are typically estimated using AOAC (2000) and other standard protocol.
Requirements
Biomass samples (such as agricultural residues, cattle dung, poultry litter, paddy straw and others materials from living organisms but now dead), silica crucible, hot air oven, desiccator, muffle furnace, weighing balance, 5% Phenol, concentrated H2SO4, UV-VIS spectrophotometer, vortex mixer, glassware like beaker and test tubes

6.1 Characterization of solid pyrolysis products

 Biochar can be characterized for its utility as well as its energy usage. Thevarious characteristics of biochar can be categorized as follows:

i. Proximate analysis

 •            Raw moisture

 •            Hygroscopic moisture

 •            Volatile matter

 •            Ash content

 •            Fixed carbon content

 ii. Ultimate analysis

 •            Elemental compositions (C, H, N, O, S)

 iii. Physical properties

 •            True density

 •            Bulk density

 •            Porosity

 •            Dry matter

 •            Particle size

 •            Pore size

 •            Pore volume

 iv. Chemical properties

 •            pH-value

 •            Electrical conductivity

 •            Carbonate content

Characterizing agri-biomass and organic waste involves various methods to determine their composition and properties. These methods are crucial for optimizing their utilization in processes like bioenergy production, biochar generation, and soil amendment. Characterizing agri-biomass and organic waste is essential for determining their suitability for valorization processes such as composting, anaerobic digestion, pyrolysis, or biofuel production. Proper characterization provides insights into the physical, chemical, biological, and energy-related properties of the waste, which influence its treatment methods, energy potential, and environmental impact.
Characterizing Agri-Biomass
1. Physical Characterization
• Moisture Content: Indicates water content, affecting energy yield, microbial degradation, and storage. Measured using drying ovens or moisture analyzers.
• Particle Size and Bulk Density: Influences handling, processing, and transport efficiency, especially in thermochemical processes.
• Total Solids (TS) and Volatile Solids (VS): TS refers to all solid matter, while VS denotes the biodegradable organic portion of the waste.
2. Chemical Characterization
• Carbon-to-Nitrogen Ratio (C/N Ratio): A vital parameter for microbial
processes. An optimal ratio (typically 25–30:1) supports composting and
anaerobic digestion.
• Elemental Analysis (CHNS/O): Determines percentages of carbon, hydrogen, nitrogen, sulfur, and oxygen, important for estimating energy content and emissions.
• Ash Content: Indicates inorganic residue post-combustion. High ash reduces energy value and may affect equipment performance.
• pH Value: Critical for biological treatments. Most microbes thrive in a neutral pH range (6.5–7.5).

Objective
To determine the chemical composition of biomass in terms of cellulose, hemicellulose, lignin, and silica content using standard detergent fiber analysis and acid digestion techniques.
Principle
Chemical analysis of biomass helps in evaluating its structural and compositional characteristics, which influence its thermal behavior, degradation properties, and suitability for bioenergy applications. Biomass primarily consists of cellulose, hemicellulose, lignin, and pentosans, each playing a distinct role in the structure and energy potential of plant material:
Cellulose – A linear polymer of ß-D-glucose units linked by ß-(1?4) glycosidic bonds. It provides tensile strength and rigidity to plant cell walls and serves as the main carbohydrate source in biomass.
Hemicellulose – A heterogeneous branched polymer composed of pentoses (xylose, arabinose) and hexoses (mannose, glucose, galactose). It acts as a matrix surrounding cellulose microfibrils, providing flexibility and binding lignin and cellulose together.
Lignin – A complex three-dimensional polymer made up of phenylpropane units. It is highly resistant to microbial degradation, provides compressive strength, and acts as a natural binder in plant tissues.
Pentosans – Polymers of five-carbon sugars that contribute to carbohydrate storage and structural integrity.

Abstract

The use of plants for treating diseases is as old as the human species. Popular observations on theuseandefficacyof medicinal plants significantly contribute to the disclosure of their therapeutic properties, so that they are frequently prescribed, even if their chemical constituents are not always completely known. Medicinal plants have therapeutic potential due to the presence of natural antioxidants functioning as reducing agents, free radical scavengers and quenchers of singlet oxygen. Majority of their antioxidant activity is due to bioactive compounds viz. flavones, isoflavones, flavonoids, anthocyanins, coumarins, lignans, catechins and isocatechins. They have been recognized to possess several medicinal properties (diuretic, expectorant, laxative, anti- bacterial, anti-pyretic etc.) and have been effectively used in the indigenous systems of medicine in India and other countries. Apart from the traditional use, a number of beneficial physiological effects have been identified by extensive studies. Among these are their beneficial effects on lipid metabolism, efficiency as antidiabetics, ability to stimulate digestion and to inhibit platelet aggregation, antioxidant, antilithogenic and anti-inflammatory potential.In this chapter an attempt has made to elucidate and understand the chemical and medicinal properties of Stavar and Safed musli those are using as medicine. These may also use as ingredients for preparation of herbal food products.

18.1 Introduction

Recycling of industrial wastewater is not only environmentally beneficial, but it is typically more cost effective than conventional treatment and discharge. Through application of stream segregation and appropriate treatment technologies, high purity water is produced for continuous reuse where by metals are recovered and solid wastes reduced. Recycling of industrial effluent by chemical treatment includes many separation methods for getting pure waters. It is very essential to discuss about reverse osmosis, filtration, adsorption evaporation etc. This chapter includes the discussion about the methodology of chemical treatments.

18.2 Conventional Treatments

The oldest and most widely applied method of wastewater treatment involves the addition of chemicals and applications of aerators etc. to alter the make-up constituents of a waste. Although generally downsized, the process continues to play an important role in newer systems used today. Automated controls and advanced instrumentation have improved this technology in recent years. (Tomer et.al., 1997)

Chemical oxygen demand (COD) is measurement of oxygen demand of waste in terms of the total quantity of oxygen required for oxidation of the waste to carbon dioxide and water. This test is based on the fact that all the organic compounds, with few exceptions, can be oxidized The test is based on the fact that all organic compounds, with a few exceptions, can be oxidized by the action of strong oxidizing agents under acid conditions. Organic matter + Oxidizing agent = CO2 + H2O. The major advantage of COD test is the short time required for evaluation. The determination can be made in about 3 hours rather than the 5-days required for the measurement of BOD
Principle
The oxidizing agents like potassium permanganate and potassium dichromate is usually used to determine COD. Potassium permanganate is selective in the reaction like it reacts with carbonaceous on the other hand it shows nonreactive with nitrogenous matter. Estimating of COD with any method, oxidizing agent must be present to ensure that organic matter is oxidized completely. The organic matter and oxidisable inorganic substances present in water or wastewater get oxidised completely by standard potassium dichromate (K2Cr2O7) in the presence of H2SO4 to produce CO2 + H2O.The excess K2Cr2O7 remaining after the reaction is titrated with ferrous ammonium sulphate [Fe(NH4)2 (SO4)2]. The dichromate consumed gives the 02 required for oxidation of the organic matter.

This chapter describes methods for evaluating soil reaction, salinity, organic matter and plant-available nutrients. It begins with soil pH and electrical conductivity, explaining their importance in nutrient availability and the identification of acidic, saline or alkaline conditions. Procedures are then provided for estimating organic carbon, available nitrogen, phosphorus, potassium and sulphur. The chapter also covers calcium, magnesium and micronutrients, including zinc, iron, copper, manganese, boron and molybdenum. Every method identifies the necessary apparatus and reagents and explains extraction, colour development, instrumental measurement, calculation and interpretation. Particular attention is given to calibration, sample preparation, reagent quality, contamination control and laboratory safe