eChapters

It is the operation of cutting, picking, plucking and digging or a combination of these operations for removing the crop from under the ground or above the ground or removing the useful part or fruits from plants.

Thresher is a machine to separate grains from the harvested crop and provide clean grain without much loss and damage. During threshing, grain loss in terms of broken grain, un-threshed grain, blown grain, spilled grain etc. should be minimum. Bureau of Indian Standards has specified that the total grain loss should not be more than 5 per cent, in which broken grain should be less than 2 per cent. Clean un-bruised grain fetch good price in the market as well as it has long storage life.

It is a machine designed for harvesting, threshing, separating, cleaning and collecting grains while moving through standing crops. Bagging arrangement may be provided with a pick up attachment. The main functions of a combine are: (i) Cutting the standing crops (ii) Feeding the cut crops to threshing unit (iii) Threshing the crops (iv) Cleaning the grains from straw (v) collecting the grains in a container.

Harvesting is the process of gathering mature crops from the fields. The timing of the harvest is crucial, as it directly affects the quality and yield of the crop.

Here are Some key Aspects Related to Harvesting Crops

Maturity: Crops need to be harvested when they reach their optimal level of maturity. This varies depending on the type of crop. For example, fruits and vegetables are usually harvested when they are fully ripened, while grains are typically harvested when they reach physiological maturity but before they start to shatter or lose quality.

Methods of Harvesting

Manual Harvesting: In some cases, crops are still harvested by hand. This is common for fruits, vegetables, and certain grains. Manual harvesting requires a significant amount of labor but is often necessary for delicate crops.

Introduction 
Due to the depletion of their raw material supplies, traditional fossil fuel use should be reduced. There is significant hope for biofuel production (Gangl D et al., 2015 ; Seo et al., 2017), and in the past decade, interest in using microalgae has been steadily increasing (Gangl D et al., 2015). The algae group consists of various photosynthetic eukaryotic species that are typically found in both freshwater and marine environments. With an estimated 30,000 to 1 million species, algae range from single-celled cyanobacteria to multicellular forms, each having distinct traits. Microalgae, specifically, grow rapidly and absorb carbon dioxide as they develop (Guiry and M. D., 2012). Many industries have benefited from the utilization of microalgae species for the good of humanity. Food, medications and antibiotics, wastewater treatment, biofuel, biofertilizers, and CO2 fixation are a few of the significant uses for microalgae (Singh et al., 2018 ; Ananthi et al., 2021). Compared to first-generation biofuels, the manufacturing of algae-based biofuel is more advantageous to the environment (Alalwan et al., 2019). Microalgal biofuel production is a greener alternative to first-generation biofuels (Alalwan et al., 2019). It can be cultivated in less ideal locations, such as the ocean or non-arable land, and doesn’t require fertile soil, which helps prevent rivalry with food crops for freshwater and farmland (Winckelmann et al., 2015; Correa et al., 2020). Microalgal production systems can help treat wastewater or convert CO2 into oxygen without interfering with the food supply (Onyeaka et al., 2021; Prasad et al., 2021). Nanotechnology and nanomaterials are becoming increasingly popular across many fields for their useful properties, with global research exploring their role in biodiesel production and processing. To speed up the development of biodiesel production, advanced nanotechnology is being emphasized to achieve higher yields at lower costs. Microalgae are a promising source for biodiesel production, and various nanoparticles can significantly boost the efficiency of harvesting them. Reusing nanomaterials and combining cell harvesting, disruption, and extraction processes also help reduce costs. Moreover, different nanocatalysts can enhance the efficiency of biodiesel conversion (Verma and Kuila, 2020). Currently available techniques for microalgal harvesting include chemical, mechanical, biological, and electrical ones to some extent. Harvesting microalgal biomass is most often done by mechanical means since they are the most dependable (Grima et al., 2003 ; Christenson et al., 2011). But, in order to increase productivity and reduce operating and maintenance expenses, these procedures are frequently followed by biological or chemical flocculation phases. For maximum separation efficiency and minimum cost, two or more of these techniques are frequently used. For instance, processing costs can be significantly decreased by combining centrifugation and flocculation-sedimentation (Schlesinger et al., 2012). Novel approaches like biological treatments have the potential to further lower operating expenses.

Q. 1 Psychrometric chart is a graphical representation of which properties
of air
(A) Chemical        (B) Aerodynamic
(C) Hygroscopic   (D) Thermodynamic

4.1 Introduction

Heat is energy which flows due to difference in temperature. Whereas energy is stored heat. Therefore, when the heat energy transfer is completed. It is stored in the form of potential or kinetic energy, in general as internal energy. Heat as energy is measured in terms of observed changes in other forms of energy & other physical properties. A heat transfer analysis is required for estimating the size, the efficiency and cost of the equipment necessary to transfer a specified amount of heat in a given time. It is well known fact that the size of a solar collector or a heat exchanger depends not so much on the amount of heat to be transmitted but rather on the rate at which heat is to be transferred under given conditions.

4.2 Modes of Heat Transfer

Heat is transferred from one body to another in three possible ways, conduction, convection, and radiation.

6.1 Introduction

Greenhouses play an essential role in modern agriculture and horticulture by providing a regulated environment for plant development. To ensure optimal growing conditions and maximum yields, it’s crucial to maintain the temperature inside these structures effectively. This leads us to the fascinating subject of “Heating and Cooling of Greenhouses,” where we investigate the delicate balance between temperature, humidity, and ventilation to promote plant health and production. With greenhouses, growing seasons can be extended, a broader range of crops can be grown, and even plants that would not do well in the local environment can thrive.

1. Herbs and Spices
       
    1.    International Standards Organization (ISO) defines spices and condiments as: Vegetable products or mixtures thereof, free from extraneous matter, used for flavouring, seasoning and imparting aroma in foods.

    2.    Rosengarten describes a spice as a product which enriches or alters the quality of a thing, for example altering the taste of a food to give it zest or pungency; a piquant or lasting flavouring; or a relish. The term ‘spice’ is thus used to cover the use of spices, herbs and certain aromatic vegetables to impart odour and flavour to foods.

    3.    Herbs may be defined as the dried leaves of aromatic plants used to impart flavour and odour to foods with, sometimes, the addition of colour. The leaves are commonly traded separately from the plant stems and leaf stalks.

10.1. Heterosis

Occurrence of a genetically superior offspring from mixing the genes of its parents.

Superiority of F₁ hybrids over its both parents in terms of yield and vigour.

8.1. Biofloc aquaculture

Among the innovations in the field of aquaculture, biofloc technology (BFT) has attracted great attention due to its ability to foster the goals of sustainable aquaculture (Khanjani et al., 2022a). If implemented correctly, BFT capitalizes on the existing organisms in water to significantly reduce water use and environmental impact and increase biosafety at farms (Avnimelech, 2012).

Water is essential for life and most of the civilization flourished on bank of rivers like Indus valley, Mesopotamia, May, INCA and also destroyed in lack of water. Scarcities and famines were the common phenomena of the world civilization. Systematic dry cultivation started around 1850 and improved techniques were started in use in USA. 

Ice cream has evolved from simple frozen preparations into a sophisticated food industry combining dairy science, food chemistry, refrigeration, microbiology, processing technology, packaging, and cold-chain management. This chapter introduces the historical development of ice cream and explains its transformation from a luxury product into a widely consumed frozen food. It examines the characteristics of the industry, major categories of ice cream and related frozen products, flavour classifications, composition, and quality characteristics. The chapter also presents the basic manufacturing process, important quality-control parameters, common manufacturing challenges, and emerging industry trends, providing a foundation for understanding ice cream as both a technical product and a commercial business.

Key words : Horticultural Resource Information System. INARIS.

Introduction

Wide ranging Indian climatic conditions are well suited for boosting production of a variety of horticultural crops (fruits, vegetables, flower/ornamental/medicinal and aromatic crops) which presently hold an important position in the global scenario. Development was at a very low ebb till the Third Five-Year Plan and increased significantly since the Seventh Five Year Plan (Rs.10,000 millions plan outlay). Government of India established National Horticultural Board (NHB) in 1984 and Agriculture and Processed Food Products Export Development Authority (APEDA) in 1986 to facilitate its larger development. The outlay is expected to increase even more in the Tenth Plan. Significant progress has been made in area expansion of different horticultural crops resulting in higher production. Besides, use of modern technologies has also brought about improvement in productivity. More than 50 per cent increase in production is seen in many of the horticulture crops during last one decade.

The efficient planning and implementation of different developmental programs on horticultural crops depends on production parameters like soil suitability, varietals dominance, marketable surplus, marketing channels, post harvest handling practices, cost of cultivation and market availability for sustained production. In addition, information on latest technologies developed by various research organizations on horticultural improvement, production, protection and post-harvest technologies are needed to be collected and made available to the scientists, planners and managers working in the related fields. But the available information on this aspect is scattered and the database is too weak to provide adequate support for developmental strategies. The digitization of comprehensive database on horticultural crops will definitely enhance the pace of increasing the area, production, productivity and promoting industry of horticultural crops that have taken lead in the new millennium with reference to nutritional quality of food and export potential. A strong, well-knit database to support need-based, market-driven and cost-effective horticultural development is imperative. Therefore, under National Agricultural Technology Project (NATP) a Mission Mode Sub-project on “Integrated National Agricultural Resources Information System (INARIS)” has been taken up to evolve a comprehensive computerized data management system on various agricultural resources like crops, animals, fishes and natural resources by harnessing RDBMS and GIS. The Co-operating Center at Indian Institute of Horticultural Research, Bangalore has developed the “Horticultural Resources Information System” with the objectives of (i) integrating existing databases in horticulture, (ii) designing and developing a comprehensive database in horticulture and (iii) developing resource maps of major horticultural crops in the country by integrating attribute and spatial data through GIS. In addition to simple storage and retrieval it will include other functions such as manipulation and dissemination of information to various users. This database will be integrated with 13 other Co-operating Centers dealing with different agricultural resources through a virtual private network (VPN). The Lead Center at Indian Agricultural Statistics Research Institute, New Delhi provide warehouse facility with a capability to analyze the data variously and provide report as cubes, tables and graphs to form a national database to cater to the needs of the users through a website. The facility of retrieving information as value-added maps using GIS will also be built in.

Horticulture involves the cultivation of fruits, vegetables, nuts, seeds, herbs, sprouts, mushrooms, algae, flowers, seaweeds, non-food crops such as grass and ornamental trees and plants. Various agricultural implements and tools are used in horticulture to facilitate the cultivation, care, and harvesting of these crops. Some common implements and tools used in horticulture:

Hand Tools

Pruning Shears/Secateurs: Used for cutting and shaping plants by removing unwanted branches or stems.

Hand Trowel: Small handheld tool used for digging, planting, and transplanting.

Pruning Saw: Used for cutting larger branches or stems.

Abstract

Human Resource Management (HRM) is an essential function of every organization. Information Technology (IT) application has made such ‘human resource management’ function easy, to a great extent. Now a day, IT has been used widely across the organizations to perform different functions like, Recruitment, training, maintenance and development etc. Human Resource Information System (HRIS) is one of the latest contributions of IT to the area of human resource management, which is going to revolutionise management in 21st Century. Technology has brought changes in the existing working styles of organisations. By the introduction of HRIS, it enhances the efficiency of the organisation by changing the traditional way of working. In Human Resource Information Systems, many organizations use employee data in traditional ways. These can create conflict with the rights and interests of employees, with external stakeholders, and with society at large. The present paper discusses such issues. Other soft issues like, challenges and possible solutions are also discussed.

6.1. Humus

Fraction of organic matter.

Complex and resistant mixture of brown or dark brown amorphous and colloidal organic substance.

6.2. Humus formation

1. Decomposition: Chemicals in the plant residues are broken down by soil microbes.

Simpler chemicals are metabolized into new compounds in the body tissue of soil microbes.

New compounds are subjected to further modification and synthesis as the microbial tissue is subsequently attacked by other soil microbes.

Symbolic systems provide logical reasoning and explicit knowledge representation, whereas sub-symbolic models offer learning, adaptation and pattern-recognition capabilities. This chapter explains how combining these approaches can create more accurate, adaptive and interpretable intelligent systems. It discusses rule-based systems, logic programming, ontologies, neural networks, fuzzy systems, evolutionary computation and swarm intelligence. Neural-symbolic, neuro-fuzzy, rule-augmented and ontology-aware architectures are examined, along with loose, tight and deep integration strategies. Applications in healthcare, cybersecurity, manufacturing and knowledge-based information systems demonstrate their practical potential. Challenges involving integration complexity, scalability, knowledge engineering, transparency and continuous updating are considered, together with future directions in human-centred hybrid intelligence.

Hydraulic pumps are the devices utilized to transfer pressure energy to liquids at the expense of electrical energy. The electrical energy is transferred to a motor which converts it into mechanical work and a pump is coupled to the shaft. The pump converts the mechanical energy to hydraulic or potential energy. 

INTRODUCTION
Hydraulics is the study of liquids and their behavior, specifically focusing on the use of pressurized fluid to generate power in engineering systems. Hydraulic systems operate by applying pressure to a small amount of fluid, which in turn generates significant power. The development of hydraulic technology has enabled major advancements, such as lifting heavy loads and rotating large shafts with minimal effort through mechanical linkages.
Compared to mechanical and electrical systems, hydraulic power systems offer greater flexibility and produce more power relative to their size. They also provide quick and precise responses to control inputs. As a result, hydraulic systems are widely used in modern applications such as aircraft, automobiles, heavy industrial machinery, and various machine tools. This article will focus on the hydraulic systems used in tractors.
HYDROSTATIC TRANSMISSION
Hydrostatic transmissions rely entirely on hydraulics, using the power of oil to transmit energy. The system consists of two main components: a variable displacement pump and a hydraulic motor. The pump’s displacement is controlled by a movable swash plate, which adjusts the piston stroke. Essentially, the system operates as a variable-displacement hydraulic pump driving a fixed-displacement hydraulic motor.
The key benefits of hydrostatic transmissions include the ability to infinitely vary ground speed and rapidly change directions. They are also known for their reliability, with self-protecting features that prevent operator abuse.
Additionally, foot pedal-controlled systems have a built-in safety feature that allows for a controlled stop simply by lifting the foot from the pedal. However, hydrostatic transmissions have some drawbacks, including high cost, sensitivity to contamination, and slight power loss at the PTO shaft. Additionally, when

Hydraulic turbines is a device which transforms the hydraulic energy or potential energy existing with the working medium to mechanical energy. The working medium is normally water which run the hydraulic turbine. The hydraulic energy is available with water by virtue of its height or altitude. The water which flow through the mountains is stored by constructing a dam or reservoir.

In drip irrigation water is distributed throughout the field from a system of pressurized pipelines. The pressure must be sufficient to overcome the frictional losses and elevation differences. The system also deserves discharge from all the emitters and the emitters must dissipate the pressure difference between the inlet to emitters and atmospheric pressure.

The flow through the drip pipes may be laminar or turbulent or a combination of both. The laminar flow is characterized by the layers of cylindrical tubes of which the maximum velocity is at the center about double of the average velocity. The turbulent flows having pulsatory cross current velocities and maximum velocity is about only 1.25 time of the average velocity. Turbulent f lows loss more energy than laminar flow due to development of the cross current velocity.

Reynolds Number

The criterion for distinguishing the flow from laminar to turbulent was developed by Osborne Reynolds (1842-1900) and was named as Reynolds number; Re . The Reynolds number in circular pipes flowing full is expressed as

11.1. Hydraulic system

It is a mechanism in a tractor to raise, hold or lower the mounted or semi-mounted equipment by hydraulic means. All the present day tractors are equipped with a hydraulic control system for operating three point hitches. Some of the tractors are fitted with a hydraulic brake system and a few others are fitted with a hydraulic steering system. Tipping trailers, front mounted loaders or dozers are examples of multi use of hydraulics.

11.2. Principle

The working principle of a hydraulic system is based on Pascal’s law (Fig 11.1.) This law states that the pressure applied to an enclosed fluid is transmitted equally in all directions. A small force acting on a small area can produce higher force on a surface of larger area.

14.1 Introduction

Hydro-electric power is electricity produced by the movement of fresh water from rivers and lakes. Gravity causes water to flow downwards and this downward motion of water contains kinetic energy, that can be converted into mechanical energy, and then from mechanical energy into electrical energy in hydro-electric power stations. (“Hydro” comes from the Greek word hydra, meaning water). At a good site hydro-electricity can generate very cost-effective electricity.

Abstract

The Mesozoic sediments contribute around 54% of the oil and 44% of the gas reserves of the world (Bois et al. 1982). Indian Mesozoic basins occupy an area of about 400 x 103 sq. km and are characterized as frontier basins under category II - IV. These basins are mostly overlain by the Deccan Traps of Late Cretaceous age and are least explored. Deccan Syneclise is one of the largest Mesozoic basins in India, covering an area of ~ 273 x 103 sq. km. Geophysical studies have inferred hidden sub-trappean Mesozoic sediments with thickness up to 2.5 km. It is considered that requisite heat generation due to Deccan Trap volcanism soon after the Cretaceous sedimentation may have acted as a catalyst in hydrocarbon generation. Surface geochemical prospecting surveys along with carbon isotopic studies have been used to assess hydrocarbon generation potential of this part of the basin. The area adjoining Nandurbar beneath Narmada-Tapti region of Deccan Syneclise was selected for geochemical studies where geophysical studies have shown considerable sediment thickness. Surface geochemical studies indicate the generation of light gaseous hydrocarbons, C1 and SC2+ in the range of 3 to 1187 ppb and 1 to 1449 ppb, respectively. The carbon isotopic signatures of selected soil gas samples dC13 CH4 in the range of - 24 to -39.4‰ PDB) suggest thermogenic origin

Abstract

A total of 30 groundwater samples were collected in four different seasons (Pre Monsoon, South West Monsoon, North East Monsoon and Post Monsoon) from the coastal aquifers of Kalpakkam region of Tamilnadu. The samples were collected covering the seasonal and lithological variations to infer the influence of natural geochemical processes and anthropogenic sources on the groundwater chemistry. The collected samples were analysed for the parameters like EC, pH and Major ions. The saturation index of silicates and carbonates shows that state of saturation to over saturation, but the sulphate minerals is dominantly under saturated. In the inverse modeling three models are obtained using PHREEQC and the error percentage is noted as 7.45%.

Abstract

In Gadilam river basin, groundwater is found in both hard rock and sedimentary terrain and is the most important source of rural/urban drinking water supply. Gadilam river basin has gained its importance due to the presence of Neyveli Lignite open cast mine (NLC), group of industrial estate (SIPCOT), extensive depressurization of Cuddalore aquifer and boreholes of New Veeranam Scheme (NVS) in the downstream of the basin. A total of 178 water samples were collected in four different seasons at various lithologies. The collected samples were analyzed for various physico-chemical parameters using standard procedures. Geochemical indicators of groundwater were used to identify the chemical processes that control hydrogeochemsitry. Interpretation of hydrogeochemical data suggests that leaching of ions followed by weathering and anthropogenic impact controls the chemistry of the groundwater. Isotopic study reveals that recharge from meteoric source in sedimentary terrain and rock water interaction with significant evaporation prevails in hard rock region. This thorough understanding helps us to make judicial usage and to maintain the quality of this commodity.

Abstract

Quality of water is affected by natural and man induced contamination to groundwater system. Area chosen for study has gained its own importance due to the location of two lignite mines and a Thermal power plant in operation. Extensive large scale pumping of water is done for lignite mining. The mine drainage and drainage from thermal power plant along with agricultural return flow from lignite charged waters increases the severity of problem. In order to achieve a panacea for the above-mentioned situation, the study has incorporated and integrated in all related factors to get a meaningful interpretation for groundwater quality and quantity management in and around Neyveli area. The frequent failure of monsoon has added to the existing problem of over exploitation. To attain a panacea for water chemistry groundwater samples were collected for four different seasons. Higher EC and TDS values are observed in Southeast and Southwest part of the study area. In Southwest monsoon and Summer seasons HCO₃Cl dominates the anions, with few representations for SO₄. In Northeast monsoon and Post monsoon season Na + K – Ca + Mg is the dominant. Thermodynamic, studies reveal that groundwater of the region are stable with Kaolinite stability field in all the silicate systems. Bicarbonates derived from silicate mineral weathering are noted in the NW, Northern and in the mining region. These regions are located in the NW and NE part of the study area. Comparison of water quality to standards shows that the water can be used for drinking and for irrigation purposes except in few locations.

Common groundwater investigations include necessary considerations of the system’s influx sources, flow regime, discharge points and geomorphological characteristics of the area. Often, hydrogeomorphological mapping of an area is required as to determine these characteristics. The primary data can be acquired from the survey of India toposheet map and the satellite images. The secondary data set includes the satellite imageries, the preparation of digital elevation model (DEM) and digitized precipitation maps.

The first step in the procedure of hydrogeomorphological mapping is to calculate the watershed/basin area, which serves as a mask to define the area of interest. The watershed/basin calculation relies on the digital elevation data and assumes that topographic aspect (dip direction of the cell surface) completely controls the extent to which surface flow emanating from each point in the study area can reach the low point in the valley. The calculation of the potential annual recharge of the aquifer combines techniques described above with data for recharge areas, DEM aspect, and precipitation. First, the catchment area of the recharge zones must be calculated in a process similar to the watershed analysis, returning the area associated with the catchment coded as “1”. A simple multiplication overlay with the precipitation data and the catchment areas yields a result giving the amount of precipitation for each catchment cell. Before using the precipitation data, we converted it to meters so as to keep units consistent. The precipitation amounts within the catchment area (i.e. each cell value) are to be summed, yielding the amount of water available for influx into the groundwater system. Finally precipitation per year data can be acquired.

Identifying surface areas of groundwater discharge is based on the observation that such areas provide a relatively constant source of moisture, which is readily exploited by vegetation in semi-arid region. Thus areas with year-round green vegetation are assumed to be indicators of discharge. The relative amount of vegetation in a scene can be estimated by calculating a vegetation index (Reddy et al, 1989 and Tucker 1979).

The world is head98ing towards a water crisis. Africa and West Asia are likely to be worst affected by water scarcity, but with increasing population, water may fall short even in the other parts of the world. According to the recent UN report, the supply of clean and fresh water is depleting at such an alarming rate in some regions, that within 30 years, about two third of population will suffer moderate to severe water stress.

In hydrogeomorphological context of social environment the water is an essential natural resource for sustaining life. The available water resources are under tremendous pressure due to increased demands. The time is not far when water, which is the free gift of nature, will become a scare commodity. Therefore, conservation and preservation of water resources are urgently required to be done at priority basis. Water management has always been practiced in our communities since ancient times. But such practices have faded away during the past few decades mainly due to lack awareness. Hydrogeologists feel that the water harvesting practices must be urgently implemented to overcome the problem of water crises. In India the Ministry of water Resources is endeavouring to make rainwater harvesting a part of every day life in villages and cities as a people’s movement. Hydrogeomorphological aspect of social environment include (a) Social - Cultural -Administrative Consideration (b) Education and Training in Hydrogeology for Professionals and Technicians (c) Education for Farmers and Women (d) Education for Masses. These are described as below:

The beginning of the 20^th century was heralded by methodological revolution in geomorphological studies brought in by Davis (1899). His classical model of geographical cycle defined by him ‘ as a period of time during which and uplifted landmass undergoes its transformation by the process of land sculpture ending into a low featureless plain (peneplain)’ dominated the geomorphological investigations all over the world throughout 1^st half of the 20^th century.

The statistical techniques by Horton (1932 and 1945) brought quantitative revolution in the field of geomorphology when he presented quantitative analysis of morphometric characteristics of fluvially originated drainage basin. Post 1950 geomorphology has undergone vast change in the methods and approaches to the study of landforms, conceptual framework, paradigm and thrust areas of study. The most outstanding contribution to the advancement of geomorphological knowledge in this period is the adoption of quantitative approach based on deductive scientific method to the study of landforms and processes at short spatial and temporal scales (Strahler, 1956 and Schumm, 1956).

Several attempts have been made in the world in past to classify large territories and landforms into morpho-units. Valuable contributions pertaining to landform analysis have been summarized below: Joerg (1914) subdivided North America into natural regions, Fenneman (1914) established physiographic boundaries and gave physiographic divisions of the United States, whereas Anderson (1941) gave physiographic divisions of Columbia plateau. Howard and Spock (1940) and Weaver (1965) presented the excellent ways of classification of the landforms while Wood and Snell (1960) applied the quantitative systems for the classification of the landforms. However, Linton (1951) and Hammond (1954 and 1965) gave techniques for mapping delineating small scale and large-scale landforms.

6.1 Introduction

When rainfall strikes a ground surface, some losses like initial and infiltration will occur. After these losses are fulfilled, runoff will begin. The runoff will ultimately reach a stream. The main routes through which runoff flows are (i) overland flow, (ii) interflow and (iii) groundwater flow. Overland flow which is also called as surface flow flows over the land mass and reaches a stream. Overland flow soon reaches a stream and if it occurs in sufficient quantity, it forms an important element in the formation of flood peaks. In small and moderate storms, there may have predominant initial and infiltration losses resulting minimum amount of surface runoff and this is especially true in case of permeable soils. If the soil is impermeable, then there may have reasonable runoff. However, surface runoff is an important factor in streamflow only for heavy or high intensity rainfall.

Water is a social requirement. Society now become aware about it’s dependence upon water and hence realized the importance of water in sustaining not only the development but also life. Water: too little, too much, too dirty; is general scenario in the world. But with increase in population water become limiting resource and is becoming scarcer and scarcer day by day. As water become scarcer commodity, the users (stakeholders) become more conscious regarding their share in water and ultimately this situation may lead to water conflicts. Earlier water related problems were generally tackled by hydro-engineers, but now in present climate changed scenario these problems go beyond the hydraulics and hydrology. Now a days politicians, ecologists, Non Government Organizations (NGOs), the media and the stakeholders etc are playing a crucial role in decision making in respect to water management issues. Now water projects are designed in reference to social context (Social context means cultural, economic, political, sociological, legal and other such aspects). When social factors are taken into consideration while tackling the water problems, it could not possible to satisfy all involved. Thus it is required to agree upon a compromise solution acceptable to all. Over recent few decades, information and communication technology (ICT) flourishes with great advances. It provides the ways to search for compromise solutions. In this chapter information, hydroinformatics, evolution of hydroinformatics and role of internet in hydroinformatics are discussed.

In this era of computer, mathematical models become integral part of hydrologic studies due to advancement in soft technology. But question always arises as ‘Why should modeling?’ It was well expressed by Rosenblueth and Wiener (1945) as

No substantial part of the universe is so simple that it can be grasped and controlled without abstraction. Abstraction consists in replacing the parts of the universe under consideration by a model of similar but simpler structure. Models, formal or intellectual on the one hand, or material on the other are thus a central necessity of scientific procedure.

Water is the most important natural resource that governs and exercises control on living organisms on earth besides supporting all human activities. The demand for water is almost increasing at exponential rate due to increase in population and industrialization. All sectors of agriculture including crop production, horticulture, animal husbandry, poultry and fi sheries primarily depend upon water. Water scarcity can cause all kinds of miseries. The water exists in all 3 different forms on earth. It exists as snow or ice in glaciers and ice caps, liquid water in rivers, lakes, streams, tanks, ponds and as groundwater storage. The water exists in all three different forms in the atmosphere. The clouds may contain fi ne ice particles, tiny water droplets and as well as water vapour. The air in atmosphere also contains water vapour. It is estimated that 97% of water is salt water and remaining 3% of water is pure and fresh water. Approximately two-thirds of the fresh water is trapped in glaciers and ice caps. Most of the fresh water (30%) exists as groundwater. About 0.7% of fresh water exists as soil water and 0.3% a fresh water accounts for surface water resources and water present in the atmosphere as water vapour, water drops and ice particles. The circulation of water between oceans, earth and atmosphere forms hydrologic cycle.
2.1. Hydrological Cycle
The hydrological cycle explains the continuous recirculation and transport of water between the atmosphere, oceans and earth. It is a very complex system that has many sub cycles associated with it. For example, the water from earth surface, oceans and water bodies get evaporated due to heat energy received from the sun in the form of incident solar radiation (Fig.2.1).

Groundwater exists at many places beneath the surface of the earth. It is normally hidden from view but, on occasion, can be seen flowing from springs and wells or seeping into tunnels. Certain properties of the various geologic materials control the ability of groundwater to enter into, move through, be stored in, or be extracted from the ground. Therefore, an understanding of geology is necessary in order to gain an understanding of groundwater found within a particular area of investigation. A basic part of the study of the geology of an area includes the preparation of a map showing surfacial exposures of each rock type. Interpretation of the map facilitates the study of the underground configuration, characteristics, and physical properties of these materials. This, in turn, enables the evaluation of groundwater storage, movement, and yield, as well as the identification of areas of ground water quality problems, recharge, and extraction.

The fundamental unit of a geologic study is the geologic formation. A formation has been defined as any assemblage of rocks, which have some character in common, whether of origin, age, or composition. In this sense, the term “rock” is defined as any naturally occurring part of the earth’s crust, made up of aggregate of minerals and includes hard, dense granite, lava ash, clay, sand, and even loose-uncohesive soil.

Q. 1 The Lysimeter is used to determine
(A) Sun shine hours   (B) Wind velocity
(C) Flow velocity        (D) Evapotranspiration

A disaster is sudden event that causes significant damage to the people, environment and the economy. Disasters are serious disruptions to the functioning of a community that exceed its capacity to cope up using its own resources. The disasters that result either due to excess water or severe water deficit are floods and droughts.
12.1. Floods
The flood is an overflowing of water onto land that is normally dry. Floods may occur due to
• Heavy rainfall
• Ocean waves
• Snow melting
The economic losses due to floods will be very high and nearly 68 per cent of the economic losses are attributed to floods only. During the year 2018, India suffered a loss of nearly 90,000 crores due to floods alone. There are several causes for occurrence of floods in India. The major causes are
• Severe cyclonic storms in coastal areas which produce continuous heavy rainfall for 3 to 4 days in succession
• Encroachment of flood plains with residential structures
• Inadequate strength of river banks when there is high flows of water in the rivers
• Unplanned growth of urban areas
• Silting of water storage structures due to increased soil erosion thereby decreasing the storage capacity of reservoirs
• Simultaneous flooding of rivers and tributaries due to excessive water flows

5.1 Introduction

Hydroponics is a method of growing plants in a nutrient solution rather than in soil. Terrestrial plants may be grown with only their roots exposed to the nutritious liquid.

Traditionally, the soil supports the crop’s roots by helping them remain upright and ensuring the delivery of water and essential nutrients. In hydroponics farming, crops are supported by an inert medium such as perlite, gravel, or other substrates. Therefore, the nutrients are supplied by using various practices that bring mineral nutrient solutions to the crops. In the present situation there excessive use of chemical fertilizers, affecting fertility of soil is badly affected. The fertility of the soil is falling that affects the plants growth but in hydroponics, the plant remains unaffected. Plants grow faster than in soil. Produce better quality of plants and higher yields. It use less water. It is possible to use hydroponics on outdoor crops, but most of the hydroponics production is in greenhouse. Hydroponic farming system has the potential to reduce the problem associated with traditional crop production. Therefore, it could serve to be a turning point in feeding the global population. The greenhouse and its environment control system are the same whether plants are grown conventionally or with hydroponics. The difference comes from the support system and the method of supplying water and nutrients.

The hydroponic farming has been successfully demonstrated by the commercial growers for fast-growing crops such as tomatoes, cucumbers, spinaches, lettuce, radishes, strawberries, bens, spring onions, coriander, and ornamentals. Indeed, hydroponics technology enables a more precise control of micro climatic conditions. In this technique, the vigorous development of a root system is taking place, which enable the uptake of essential nutrients from nutrient solution for better crop yield. The initial investment in hydroponics farming is high and required constant energy input. Owing to this, hydroponics farming is recommended for growing high value crops in developed countries such as the United States, Canada, Europe and Japan.

Abstracts

To ensure safe food and adequate sanitation programs, the equipment used for processing of food products must be designed, fabricated, constructed, and installed according to sound hygienic design principles. This ensures the equipment can be adequately cleaned and sanitized, and that surfaces are resistant to daily exposure to corrosive food products and cleaning/sanitizing chemicals. This chapter focuses primarily on fundamental principles of hygienic design, which protect the product from microbial, chemical, and foreign-body contamination. This is followed by a discussion of general aspects of hygienic construction and design of food equipments, the selection of materials of construction and specification of surface finishes, fabrication, installation and cleaning and sanitization. Quality of raw materials or foods ingredients, proper processing, packaging and storage of finished products decides the quality of the food products. Planning for plant and equipment layout, its design, services (water, air, refrigeration, steam), waste disposal etc. are some of the critical factors, which contributes to quality. In addition, the food processing equipment must comply with strict standards and regulations, which are necessary for securing the quality and safety of the food products to the consumers.

ABSTRACT

This paper reviews the various application of hyperspectral remote sensing data carried out by the scientists of India emphasizing its advantages.

1. INTRODUCTION

The most significant recent breakthrough in remote sensing has been the development of hyperspectral sensors. The ‘Hyper’ in hyperspectral means ‘too many’ and refers to the large number of measured wavelength bands. Hyperspectral images are spectrally over determined, which means that they provide ample spectral information to identify and distinguish spectrally unique materials. Hyperspectral imagery provides the potential for more accurate and detailed information, extraction than is possible with any other type of conventional remotely sensed data.

Imaging spectroscopy (Goetz et al., 1985) in hyperspectral imaging is concerned with the measurement, analysis, and interpretation of spectra acquired from a given scene (or specific object) at a short, medium or long distance by an airborne or satellite sensor. The concept of imaging spectroscopy originated in the 1980's, when A. F. H. Goetz and his colleagues at NASA's Jet Propulsion Laboratory began a revolution in remote sensing by developing new instruments such as the Airborne Imaging Spectrometer (AIS), then called AVIRIS, for Airborne Visible Infra-Red Imaging Spectrometer (Green et al., 1998). This system is now able to cover the wavelength region from 0.4 to 2.5 μm using more than two hundred spectral channels, at nominal spectral resolution of 10 nm. The special characteristics of hyperspectral datasets pose different processing problems, which must be necessarily tackled under specific mathematical formalisms, such as classification and segmentation (Jia et al., 1999, Green, R 1998) and spectral mixture analysis (Adams et al., 1986; Smith et al., 1990a, b).

ABSTRACT

In earth system about 60% of the world's population live within 60 km of coastline and use the coastline for their livelihood. Environmental pollution of the coast, inshore water and deep ocean is one of the important topical issues in the context of human health and global warming. To combat this natural and man made problem, we have to rely on qualitative analysis quantitatively. In the recent advancement in information and technology field, spectral data plays a major dominant role in the environmental studies. This could provide more powerful and accessible means to exploit the enormous wealth of data available in the system. The high-resolution imaging spectrometry (hyperspectral imagery) will help to analyze the data for mapping and other environmental modeling applications. This could attain advanced approaches to deduce surface characteristics and extract features from hyperspectral images. The current capabilities are in which, the prototype system can classify pixels according to surface type. The classification process employs neural network analysis of inputs which include pixel spectra and a variety of processed image metrics, including image “texture spectra” derived from fractal signatures computed for sub image tiles at each wavelength. Thus, this kind of technical analysis can prove to achieve coastal area studies well in advance in the ongoing environmental changes more precisely.

ABSTRACT

Multispectral imagery has been used as the data source for natural resource mapping and land observational remote sensing from airborne and satellite systems since the early 1960s. Over the past two decades, advances in sensor technology have made it possible for the collection of several hundred spectral bands. This is commonly refe rred to as hyperspectral imagery. Thus it is possible to construct a complete reflectance spectrum of every pixel in the scene. This review highlights the hyperspectral remote sensing system development, hyper spectral data processing and difference between multispectral and hyperspectral data; spatial and spectral resolutions and focuses on the application of hyperspectral imagery in natural resource studies and, in particular the classification and mapping of land resources.

ABSTRACT

Remote sensing has undergone tremendous development in past decades. Hyperspectral imaging refers to the imaging of a scene over a large number of discrete, narrow contiguous spectral bands in the visible through thermal infrared portion of the spectrum. Thus it is possible to construct a complete reflectance spectrum of every pixel in the scene.

Classification of hyperspectral image requires thorough understanding of surface material properties, sensor characteristics and atmospheric absorption spectra. The reflectance spectra of most materials on the Earth's surface contain diagnostic absorption features. Remote sensors, capable of acquiring complete reflectance spectra over large areas, offer a powerful tool to study of the Earth and the environment. Methods are being developed to extract information from remote sensing data using image-processing approaches. Specific absorption features of reflectance spectrum can be used to identify a number of important rock forming minerals, and have been used by geologists for geologic mapping and studies of volcanoes.

The present discussion includes an application of thermal characteristics of near- IR bands of Landsat TM to estimate the temperature of over and around the crater of Barren Island volcano in 1991. A method using dual band temperature characteristics related to radiant source of sub-pixel size was developed and utilized to prepare temperature contour map of the Island using unsaturated pixels of band 5 and 7.

ABSTRACT

Over the last decade, hyperspectral remote sensing has become a powerful analysis tool for applications in environment and ecology, aquaculture, forestry, agriculture, and geoscience. A hyperspectral imagers advantage over broadband sensors, such as Landsat Thematic Mapper (TM) and the SPOT Haute Resolution Visible (HRV) sensor series, is its ability to detect molecular absorption and particle scattering signatures of constituents. The finer spectral resolution of a hyperspectral imager allows detection of surface materials and their abundances, as well as inferences of biological and chemical processes. This review highlights the vast extent to which hyperspectral technology and their application with special reference to ocean have been discussed.

ABSTRACT

Mineral composition and their distribution on planetary surfaces provides important clues to the evolutionary processes that the planetary bodies have undergone since their formation. For distant and inaccessible planets, remote sensing, either from Earth-based telescopes or from an orbiter around the planetary body, using reflectance spectroscopy over a wide range of the electromagnetic spectrum (UV-Visible-IR), can provide surface distribution of minerals. With advances in technology, a high-resolution hyperspectral imager onboard an orbiter has developed into a powerful tool for compositional mapping of planetary surfaces. Interpretation of the signals from these distant and relatively unknown destinations is a challenging task due to scarcity of available ground truth. Here, we describe the technique with its applicability to airless bodies, such as Moon, in the context of the Indian Moon mission, Chandrayaan-1, and, the intricacies involved in the data analyses.

Keywords : Reflectance spectroscopy, hyperspectral data, remote sensing, planets, moon

1. INTRODUCTION

The primary goal of planetary exploration is to understand the mechanism by which planetary objects (planets, dwarf planets, satellites and small solar system bodies) have evolved with time. The information gathered from the study of individual bodies is integrated to comprehend the development of our solar system. The present understanding envisages our solar system to have formed from the solar nebula, produced as a consequence of the collapse of a molecular cloud. While the central mass gravitated and formed the sun, the gas and dust surrounding it condensed to form grains and formed the proto-planetary disk. These grains, through a series of processes, finally aggregated to form of the various planetary bodies. Existing Astronomical, chemical and mineralogical evidences from studies of lunar samples, meteorites and, remote sensing observations suggest that the planetary bodies are heterogeneous and possess extreme compositional and morphological diversity. The internal energy of a planetary body, a function of its size, is responsible for the differences in the degree of differentiation a body has undergone leading to the variations in their surface composition. Large planets like the Earth and Venus are still evolving whereas the small asteroids have barely evolved after their formation and are considered primitive. The wide variety of planetary bodies in our solar system is therefore reminiscent of the various stages of evolution that our solar system went through. The degree of melting and cycling through episodes of differentiation determine the mineral inventory on a planetary body. Therefore, distribution and composition of various minerals can be used to understand various stages of chemical evolution of a planetary body. Mineral mapping of planetary surfaces is thus useful in understanding the petrogenetic history.

ABSTRACT

This paper is an attempt to highlight the problems of coastal environmental impact assessment owing to logistic constraints, costs of analytical data generation, time gap between data generation and interpretation, quantum of physical and chemical data required for assessment of environmental data through conventional methods and to examine the potential of hyperspectral remote sensing as an alternative for conventional methods. As hyperspectral remote sensing is non-destructive, offers repetitivity and high resolution (spatial and spectral) and hyper-sensitive to many physical and chemical properties of coastal soils and minerals, we recommend use of hyperspectral remote sensing for reduction of cost and man-hours in coastal environmental assessment, without compromising the quality of data.

ABSTRACT

Hyperspectral image reduction processes use only information drawn from knowledge related to the surface reflectance properties. The chemical composition and crystal structure control the shape of spectral curve, position and amplitude of absorption bands. Spectral database provide a source of reference spectra useful in classification of hyperspectral images.

An attempt has been made to put all such available data on a structured database for easy access and visualization. A Web-based interface for reference spectra of natural surfaces facilitates data sharing and increases access to reference material for classification.

1. INTRODUCTION

Hyperspectral imaging refers to the imaging of a scene over a large number of discrete, narrow contiguous spectral bands in the visible through thermal infrared portion of the spectrum. Thus it is possible to construct a complete reflectance spectrum of every pixel in the scene.

Field spectroscopy is a nondestructive way to collect information on natural resources and is becoming a common exercise in remote sensing field campaigns. Specific absorption features of reflectance spectrum can be used to identify a number of important rock forming minerals, and have been used by geologists for geologic mapping and studies of volcanoes. Spectral database provide a source of reference spectra useful in classification of hyperspectral images.

Q. 1 Which option about the statements made below is correct?
(1) The cooling system maintains engine temperature at 71 to 82ºC for petrol engines.
(2) The thermostat valve begins to open at about 60oC and opens widely at about 71ºC.
(A) Statement (1) is true, but statement (2) is false.
(B) Statement (2) is true, but statement (1) is false.
(C) Both statements (1) and (2) are true.
(D) Both Statements (1) and (2) are false.

A hunting governor is ……….
(A) Less sensitive       (B) More sensitive
(C) More stable           (D) None of these is correct

A greenfield ice cream project involves much more than installing production machinery. It requires integrated planning of the business model, market opportunity, capacity, product portfolio, plant layout, process technology, refrigeration, utilities, packaging, cold storage, quality systems, regulatory compliance, distribution, working capital, and future scalability. This chapter presents a practical framework for evaluating new ice cream manufacturing projects, with particular attention to a representative 1000 LPH facility. Different project scales and business models are considered along with major plant and machinery requirements. The chapter also highlights common project-planning mistakes and best practices. It helps entrepreneurs and investors assess technical feasibility, operational readiness, financial requirements, scalability, and long-term commercial viability.