eChapters

Aim: To verify the relationship between the input and output voltage for 3-phase transformer connection in various ways:

A 3-phase transformer can be considered as a set of 3 single-phase transformer bank or as single unit of 3 phase windings. Since three winding are available in both primary and secondary side then there can be different types of connections and so far, different characteristics.

Aim: To determine the Load characteristics (External characteristics) of self excited D.C. shunt generator.

If a dc shunt generator, after building up to its voltage, were loaded, its terminal voltage will drop. This drop increases if load increases. But this type of terminal drop is undesirable for a specified service. The relation between terminal voltage and load current is called external characteristics. Speed is to be kept constant. Reason for voltage drop:

Aim: To perform speed control of D.C. shunt motor by

1. Armature resistance control method.

2. Field (flux) control method.

This method is based on the fact that by varying the voltage available across the armature, the back EMF and hence the speed of the motor can be changed. This is done by inserting a variable resistance RC (known as controller resistance) in series with the armature as shown in Fig. (a).

Aim: Determination the equivalent circuit parameters of a single-phase induction motor.

1. No-load test.

2. Blocked rotor test.

The performance of a single-phase induction motor is generally studied either by double revolving field theory or by cross field theory, the former being simple and gives a clear physical understanding.

Aim: Perform an experiment to determine the parameters of a three-phase induction machine.

As the circuit modal of an induction motor is similar to that of a transformer, the parameter of the modal can be obtained by no-load test and blocked rotor test.

No-load test

In this test, the motor is to run at no-load at rated voltage and frequency. The applied voltage and current and power input is measured. Power input at no load (Po ) provides only the losses that are rotational losses.

Aim: To study the effect of variation of field current upon the stator current and power factor with synchronous motor running at no-load, hence to draw V and inverted V curves of the motor.

With constant mechanical load on the synchronous motor, the variation of field current changes the armature current drawn by the motor and also its operating power factor. As such, the behavior of the synchronous motor is described below under three different modes of field excitation.

About the Lower Bhavani Project

The Lower Bhavani Project (LBP) is located in Tamil Nadu in Bhavani River, irrigates 83980 ha in two seasons in a year. The canal water supply is provided for one wet crop from August to December (41885 ha) and one dry crop from January to April (41885 ha). The cultivated area under LBP in Erode and Coimbatore districts are irrigated lands with canals and groundwater, and rainfed crop lands (with supplemental groundwater irrigation).

Introduction

The issue of environmental protection has become increasingly important in recent years, and one of the most effective ways to address this problem is through the use of recycled products. Recycling helps to conserve natural resources, reduce waste, prevent pollution, and combat climate change making it a critical part of any sustainable development strategy. In this chapter, we can explore how recycled products can help protect the environment and the many benefits that come with their use.

Introduction

Eco-friendly interior design is an important consideration for anyone who wants to create a healthy, sustainable, and beautiful space.

Environmental impact: The materials used in interior design can have a significant impact on the environment. Eco-friendly materials are made from renewable resources, reduce waste, and often have a lower carbon footprint than traditional materials.

Sustainability

Sustainability is a complicated concept. The most often cited definition comes from the U.N. World Commission on Environment and Development (WCED): “Sustainable development is the development that fulfills the needs of the present without compromising the ability of future generations to meet their requirements.” Hence, sustainability has been defined as meeting our own needs without compromising the ability of future generations to meet their own needs.

Introduction: Indoor Air Pollution

People think that while they are indoors, they are breathing clean air. After all, pollution is found outside, and indoor air is filtered through the HVAC system.

Indoor air can have significantly higher concentrations of pollution than air found outside. Plenty of evidences exists. Global Burden of Disease Risk lists indoor air pollution as the ninth biggest health risk.

Introduction

India has vast livestock resources. Livestock sector includes animal husbandry, dairy and fisheries sector. Livestock provides livelihood to two-third of rural community and employment to about 8.8 % of the population in India. Livestock sector contributes 4.11% GDP and 25.6% of total Agriculture GDP. It provides milk and milk products, meat and meat products, and also constitutes a major supplier of food and food articles, raw materials, and finished products.

Climate change impacts

• Climate change is a crucial factor behind cyclone Tauktae

• Global ocean has absorbed 90% of the excess heat generated by greenhouse gas emissions since 1970

• Led to anomalous ocean warming in Arabian Sea and Bay of Bengal, which in turn makes cyclones intensify rapidly

• India will see more frequent cyclones every year due to global warming

What is A Smart Energy Home?

Smart homes use internet - connected devices to enable remote monitoring and management of appliances and systems, such as temperature, lighting, and security cameras. Smart energy homes take a step beyond the gadget-filled smart home to focus on bringing smart functionality to major household energy-using systems like HVAC, water heating, and plug loads (including appliances and electronics).

Types of Biomedical Waste

1. Infectious waste: waste contaminated with blood and other bodily fluids (e.g. from discarded diagnostic samples), cultures and stocks of infectious agents from laboratory work (e.g. waste from autopsies and infected animals from laboratories), or waste from patients with infections (e.g. swabs, bandages and disposable medical devices)

2. Pathological waste: human tissues, organs or fluids, body parts and contaminated animal dead bodies

Introduction

Site-specific nutrient management (SSNM) is the dynamic, field-specific management of nutrients in a particular cropping season to optimize the supply and demand of nutrients according to their differences in cycling throughsoil–plantsystems(Sarkar etal.,2017).Thisnewmethodofnutrient recommendationsisprimarilybasedontheinitialnutrientstatus(INS)from thesoil andthecrop’sneedfornutrients toachieve thedesiredyield.

12.1 Introduction

It is important to note that growing crops in a greenhouse requires a significant f inancial and administrative commitment. In order to ensure profitability, firms need to consider both cash flow and profitability. An enterprise budget can help address profitability potential by itemizing costs incurred across a typical production cycle. On the other hand, a cash flow budget is used to analyze the cash inflows and outflows of the enterprise over a fixed period of time.

8.1. Biofloc aquaculture

Among the innovations in the field of aquaculture, biofloc technology (BFT) has attracted great attention due to its ability to foster the goals of sustainable aquaculture (Khanjani et al., 2022a). If implemented correctly, BFT capitalizes on the existing organisms in water to significantly reduce water use and environmental impact and increase biosafety at farms (Avnimelech, 2012).