eChapters

The arid region in India is spread over in 38.7 million hectare land. Out of the total 31.7 m hectare lies in hot arid region and remaining 7 m hectare comes under cold arid region. The hot arid region occupies major part of northwestern India (28.7 m ha) and a small pocket (3.13 mha) in southern India. The north western arid region occurs between 22°30’ and 32°05’ N latitude and 68°05’ to 75°45’ E, covering western part of Rajasthan, north western Gujarat and south western parts of Haryana and Punjab. About 62% area of arid region falls in western Rajasthan and 20% in Gujarat. Haryana and Punjab together constitute 7% area of arid region. The state wise distribution of arid region is shown in Table 3.1. Further our discussion is based on the majority area of arid region, belonging to Rajasthan, Gujarat, Punjab and Haryana.

Introduction

Cooking accounts for a major share of energy consumption in developing countries. Fifty per cent of the total energy consumed in India is for cooking (Fritz 1981). Most of the cooking energy requirement is met by non-commercial fuels such as firewood (75%), agricultural waste and cow dung cake (25%) in rural areas. The fuel wood requirement is 0.4 tons per person per year in India. In rural areas firewood crisis is far graver than that caused by a rise in oil prices. Marginal villagers have to forage 8 to 10 hours a day in search of firewood as compared to 1 to 2 hours ten years ago. One third of India’s fertilizer consumption can be met if cow dung is not burnt for cooking and instead is used as manure. The cutting of firewood causes deforestation that leads to desertification. Fortunately, India is blessed with abundant solar radiation (IMD, 1985). The arid parts of India receive maximum radiation i.e. 7600-8000 MJ m^-2 per annum, followed by semi-arid parts, 7200-7600 MJm^-2, per annum and least on hilly areas where solar radiation is still appreciable i.e. 6000 MJm^-2 per annum. Therefore, solar cookers seem to be a good substitute for cooking with firewood.

Principle of cooking

The different methods of cooking of food are boiling, frying, roasting, and baking. For boiling of rice, lentils etc. the temperature of food being cooked is about 100° C while for other methods, high temperatures are required. Heat is supplied at the bottom of the vessel for frying and boiling purposes in conventional cooking. Roasting and baking is generally performed on open fire or in ovens, wherein food is surrounded by hot surfaces and heat is transferred to the food by radiation and convection.

Introduction

Considering the accountable post-harvest losses which is approximately 30-35 percent, food processing becomes an extremely important sector for preventing the losses and feeding the growing population. The Indian food industry is poised for huge growth, as currently valued at US$ 1.3 billion with compound annual growth rate of 20 per cent per year, increasing its contribution to world food trade every year. In India, the food sector has emerged as a high-growth and high-profit sector due to its immense potential for value addition, particularly within the food processing industry. Increasing population of the country and high cost of fuels have also created a demand for new alternate sources of energies for post-harvest processing of foods. Solar food processing technologies may become a viable option that provides good quality foods at low or no additional fuel costs. The energy policy of the developing countries now focuses on the clean renewable energy to create a further reduction of the petroleum import and to alter the utilization of petroleum energy toward the utilization of solar energy. It is an interesting fact that most of the developing countries fall in the climatic zone where the insolation is considerably higher than the world average of 3.82 kWh m-2 (Majumdar 2015). The daily horizontal insolation of India is approximately 5.80 kWh m-2 (Visavale 2009, Visavale et al. 2011). Solar dyers are an alternative to traditional drying technique and a contribution towards the solution of the problems of the open sun drying from perspective of renewable and clean energy. The International Energy Agency (IEA) declared in its 2011 solar energy perspectives executive summary (SEP 2011): “Solar energy offers a clean, climate-friendly, very abundant and inexhaustible energy resource to mankind, relatively wellspread over the globe. Its availability is greater in warm and sunny countries that will experience most of the world’s population and economic growth over the next decades.

Solar energy is the energy emitted by the sun in the form of electromagnetic radiation. It is the most abundant, renewable, and sustainable energy resource available on Earth. Every hour, the Earth receives more energy from the sun than the entire human population consumes in a year. This makes solar energy a key candidate for solving the world’s growing energy needs while addressing environmental concerns. The solar energy reaching Earth can be harnessed and converted into useful forms of energy
Solar Photovoltaic Fencing
Solar photovoltaic fencing utilizes solar energy to provide an effective security solution, using high-voltage electric pulses to deter intruders or animals. The system operates by converting solar energy into electricity, which is then stored in a battery for later use. The battery powers an energizer that sends high-voltage pulses along the fence, creating an electric shock when an intruder touches the live wire.
System Components and Working
1. Solar Module: Converts sunlight into direct current (DC) electricity, which charges the battery.
2. Battery: Stores the energy generated by the solar panel. The 12V/100AH battery allows the system to operate even at night or during cloudy days.
3. Energizer: The energizer is the heart of the system, generating high-voltage pulses. It works by sending electrical pulses at regular intervals (usually one pulse per second) through the fence. The energizer is powered by the battery.

3.1 Introduction

The sun emits electromagnetic radiation, which is referred to as solar radiation. Every location on the Earth’s surface receives some sunlight during the course of the year, but the amount of solar radiation varies. On a daily basis, we see much less energy from the sun than it emits and incident upon the earth. In an hour and a half, the amount of sunlight that reaches the surface of the earth is enough to provide enough energy for an entire year. 

Introduction

In Indian Thar desert regions, excessive heat is the major problem that causes human and animal thermal discomfort. Space cooling is, therefore, the most desirable factor for the inhabitants. Various examples of dwellings responsive to climatic constraints are found in vernacular architecture throughout the world. Compact cellular layout with minimum external surface exposure to the sun, whitewashed surfaces to reduce absorptivity, blind external facades, courtyards, vegetation to provide humidity and shade, and heavy buildings constructed from high thermal capacity materials are common passive features in most of the arid regions. Wind towers for cooling ventilation are well known in Iranian and Middle East architecture, which along with cooling of the air by earth and water evaporation keep the building comfortable in hot periods. Building underground to take advantage of the large thermal storage capacity of the earth is also used in Tunisia and central Turkey.

9.1 Introduction

Solar energy can be directly converted into electrical energy through photovoltaic route. Energy conversion devices which are used to convert sun light into electricity by use of the photovoltaic effect are called solar cells. The advantages of solar cells are:

1. They are reliable, convenient and durable.
2. It is green, sustainable and pollution free technology.
3. Directly solar radiation can be converted into electricity (conversion of global solar light by flat plate photovoltaic).
4. Maintenance cost is quite low therefore suitable even in isolated and remote area, since no moving parts are involved.
5. Solar cells are quite compatible with almost all environments, respond instantaneously with solar radiation.
6. Considerable expected lifetime i.e. 20 years or even more.
7. No distribution system is required, because they are decentralized source of energy and located at the place of use.

Introduction

Agriculture has been the back bone of Indian economy and culture and it will be continued to remain as such for a long time in future. Parallel to this, energy security of a country is also very important and efforts have been given on renewable energy utilization since the fossil fuel based energy is depleting at a very fast rate. In agricultural fields, considerable amount of energy is used to do different field activities e.g. ploughing, irrigation through pumps, intercultural operations, spraying of agricultural chemicals for plant protection, harvesting, post-harvest processing etc. Therefore, there is also need to replace the conventional energy source with renewable sources to operate above mentioned agricultural activities.

Approximately, 35% of the crop production is damaged if pest and diseases are not controlled at right time. Uniform spraying of liquid formulations throughout the crop field is very important for effective control of pest and diseases. Using sprayer, liquid pesticide formulations are generally broken down to minute droplets of effective size for uniform distribution over a large surface area. Different types of sprayers are used in agricultural field based on different requirements.

Introduction

Water is the primary source of life for mankind and one of the most basic necessities for crop production. The demand for water to irrigate the crops is increasing. For sustainable production from agricultural farms, irrigating the crops at right stages is highly important. Even in rainfed situation, lifesaving irrigation during long dry spell has also been found beneficial for crop survival and to obtain the targeted yield. Considering the depletion of groundwater below the critical zone in most part of the country, energy intensive pumping for irrigation is not a viable option. Therefore utilization of available runoff water through surface storage systems followed by pumping may be a potential solution to achieve the set goal of ‘crop per drop’ mission. In this connection, micro-irrigation system including drippers and sprinklers is of great importance. However, ensured power supply is essential to operate the micro-irrigation system even in remote areas. Reliable solar photovoltaic (PV) pumps are now emerging in the market and are rapidly becoming more attractive than the traditional power sources. These technologies, powered by renewable energy sources, are especially useful in remote locations where a steady fuel supply or electricity supply is problematic. About 16 million electric pumps and 7 million diesel pumps are in operations in the country for irrigation purpose; however they are highly energy intensive. Moreover, diesel operated and electrified pumps directly or indirectly emit large amount of CO₂ gas in atmosphere and hence are not environment friendly. To meet the energy demand for irrigation, solar PV pumps have been introduced under the off-grid power generation category of National Solar Mission (NSM) with a target of 1000 MW by the end of phase II (2013-2017). The target has been revised in 2015 to a total grid connected solar power generation of 1,00,000 MW comprising 40,000 MW roof top generation and 60,000 MW grid connected solar power plants (Resolution of MNRE, Govt of India, No. 30/80/2014-15/ NSM dated 1^st July 2015).

The Sun is the primary source of heat to the Earth and its atmosphere. The heat received from other celestial bodies as well as the interior of the Earth is rather too significant. The distance that separates the Earth from the Sun is about 149.0 million km. The diameter of the Sun measures roughly about 1.3824 million km. The surface temperature of the Sun is estimated between 5500^o C and 6100^o C. (or 5762^o K).

The weight of the sun is about 1.9 X 10 30kg. The radius is 6.97 X 10 8 m or the diameter of the sun is 14 X 10 5 km. The mass of the earth is 6 X 10 24 kg, the radius is 6.4 X 10 6 m. The gravitational force of the earth is 9.81m/s². Whereas the sun‘s attractive force is 274m/s². This is 25 times higher than earth’s gravitational force.

Sun is the prime source of energy injected into the earth’s atmosphere. The sun is the nearest star to the earth. It is a hot ball of glowing gases at the heart of the solar system. Its radiant energy is practically the only energy source to the earth. Very small and insignificant quantities of energy are available from other sources such as the interior of the earth, the moon, and other stars. Without the sun’s intense energy and heat, there would be no life on earth.

NATURE AND PROPERTIES OF SOLAR RADIATION

The mean distance of the sun from the earth, also known as one astronomical unit (1 AU), is approximately 1.496 × 10⁸ km, though the distance varies as the earth revolves round the sun in an elliptical orbit. At this average distance, light travels from the sun to earth in about 8 minutes and 19 seconds. The energy of the sunlight supports almost all life on earth by photosynthesis, and drives earth’s climate and weather. The minimum sun-earth distance is about 0.983 AU and the maximum is approximately 1.017 AU. The earth is at its closest point to the sun (perihelion) on around January 3 and at its farthest point (aphelion) on around July 4.

Sun is the prime source of energy injected into the earth’s atmosphere. The sun is the nearest star to the earth. It is a hot ball of glowing gases at the heart of the solar system. Its radiant energy is practically the only energy source to the earth. Very small and insignificant quantities of energy are available from other sources such as the interior of the earth, the moon, and other stars. Without the sun’s intense energy and heat, there would be no life on earth.

The mean distance of the sun from the earth, also known as one astronomical unit (1 AU), is approximately 1.496 × 10⁸ km, though the distance varies as the earth revolves round the sun in an elliptical orbit. At this average distance, light travels from the sun to earth in about 8 minutes and 19 seconds. The energy of the sunlight supports almost all life on earth by photosynthesis, and drives earth’s climate and weather. The minimum sun-earth distance is about 0.983 AU and the maximum is approximately 1.017 AU. The earth is at its closest point to the sun (perihelion) on around January 3 and at its farthest point (aphelion) on around July 4.

The sun makes up about 99.86% of the mass of the entire solar system. The visible disk or photosphere has a radius of 6.599 × 10⁵ km, and the solar mass is 1.989 × 10³⁰ kg. The sun is a completely gaseous body. The chemical composition (by mass) of the outer layers of sun is 71 per cent hydrogen, 26.5 per cent helium, and 2.5 per cent heavier elements like oxygen, carbon, neon, and iron among others. Since the sun is not a solid body, different parts of the sun rotate at different rates. At the equator, the sun spins once about every 25 earth days, but at its poles the sun rotates once on its axis every 36 days.

The process through which heat energy is transferred from a body at higher temperature to a body at lower temperature without any material medium between the two bodies is x called radiation. The outer surface of the the Sun is at higher temperature compared to the surface of the earth. Solar radiation is the electromagnetic energy emitted by the Sun. It is the primary source of energy for the Earth’s climate system, driving atmospheric and oceanic circulation, influencing weather patterns, and sustaining life through photosynthesis.2 This energy travels through space as electromagnetic waves, encompassing a broad spectrum of wavelengths, from high-energy gamma rays and X-rays to ultraviolet, visible, infrared, and radio waves. The portion of this spectrum that reaches the Earth’s surface is crucial for a multitude of processes, making thestudy of solar radiation fundamental to understanding our planet’s environment.  This introduction will lay the groundwork for exploring the characteristics, distribution, and interaction of solar radiation with the Earth’s atmosphere and surface.
5.1. Wave length of Radiation
The wavelength of radiation refers to the distance between two consecutive peaks or troughs of a wave. It’s a measure of the length of one complete cycle of the wave

Introduction 
In a time when the world is in dire need of sustainable energy solutions, investigating biofuels becomes an essential path to supplying the always expanding supply[1]. This book chapter explores the dynamic world of solid and liquid biofuels, providing a thorough analysis of their properties, methods of production, uses, and wider ramifications in relation to renewable energy sources. Setting the scene, the introduction clarifies the role of biofuels in the larger context of renewable energy. Exploring solid and liquid biofuels becomes critical as the globe struggles with issues like climate change, depleting fossil fuel reserves, and the need to switch to cleaner energy sources[2]. These biofuels, which are defined as energy carriers made from biomass, offer a viable substitute and have the capacity to both reduce environmental impact and promote energy security. As the chapter progresses, biofuels are divided into two main categories: liquid and solid. Biofuels that are solid, such as wood, agricultural leftovers, pellets, and briquettes, serve as a starting point for investigating alternative energy sources. This section walks readers through the complexities involved in producing solid biofuel, including harvesting, pre-treatment, and creative pelletization methods. By doing this, it highlights the renewable nature of solid biofuels and their ability to lower greenhouse gas emissions, highlighting their benefits for the environment. Simultaneously, difficulties associated with its application, ranging from administrative worries to land use issues, are examined closely. Turning its attention to liquid biofuels, the chapter tells the story of ethanol, biodiesel, and advanced biofuels. By examining the choice of feedstock, manufacturing procedures, and real-world uses, it highlights the adaptability of liquid biofuels in the energy system. Although they are not without difficulties related to land use, food production, and water use, their ability to function with current infrastructure and their critical role in improving energy security stand out as distinguishing characteristics[3].

Introduction

One of the major problems being faced by cities and towns relate to management of municipal solid waste (MSW). Waste quantities are increasing day by day due to the increasing population and the municipal authorities are not able to upgrade or scale up the facilities required for proper management of such wastes. In many cities and towns, garbage is littered on roads and foot-paths. Citizens are also not accustomed to use the available storage facilities (dust bins) set up by the authorities. At large, lack of organized system of house- to-house collection of waste has created the littering habits. By and large, hardly we can see any city/town complying with the Municipal Solid Wastes (Management and Handling) Rules, 2000 in ‘totality”. As per information provided by Central Pollution Control Board (CPCB), 1,27,486 TPD (Tons per day) municipal solid waste was generated in the country during 2011-12. Out of which, 89,334 TPD (70%) of MSW is collected and 15,881 TPD (12.45%) is processed or treated.

In spite of various measures taken towards the proper waste collection, segregation and disposal, proper waste processing units were established as per the following details as per CPCB. The waste processing technologies reported in the country are; composting, vermi composting, biogas plant, RDF- pelletisation and others. Some of the sepelletization plants are associated with power plants for generation of electricity. However, mechanical composting and vermi composting are more popular in the country.

3.1. SOLID WASTE MANAGEMENT

Solid waste management includes the transportation, processing, recycling and disposal of our waste materials. We live in a disposable world in many ways with the modernization and convenience of our world we have cluttered it with our refuse.

Overview
Humanity has produced trash since the beginning of time, whether it is from the bones and other parts of the animals they kill for food or the wood they harvest to build their carts. As civilization developed, garbage was produced that was increasingly sophisticated in character. The world of consumers emerged around the close of the 19thcentury as a result of the industrial revolution. The production of non-biodegradable solid waste led to an increase in pollution not just in the air but also on Earth itself. The rise in solid waste was also primarily caused by urbanization and population growth.
Definition of Solid Waste
Glass crockery containers, plastic containers, sludge, vehicle parts, and mounds of crop wastes are among the solid waste materials. These gather in public areas and hinder people’s regular activities.
Every family produces waste or rubbish on a daily basis. We usually toss away items that we no longer need or have any use for, which puts them in the garbage category. Depending on where it comes from, solid waste can take several forms. Understanding the proper ways to handle the trash produced has become crucial in today’s dirty world. One crucial technique for managing municipal solid waste is segregation. Representation provides a good understanding of segregation at source. Composting is a crucial waste management and treatment technique.

Solid wastes are all the wastes arising from human and animal activities, that are normally solid and that are discarded as useless or unwanted materials. It consists of the highly heterogeneous mass of discarded materials from the urban community as well as the more homogenous accumulation of agricultural, industrial and mining waste.

Urbanization, industrialization, and economic growth in India have all led to an increase in the generation of municipal solid waste (MSW) by a number of urban local bodies (ULBs). In cities with high population densities, SWM is a significant difficulty. Being a diverse country with a wide range of religious communities, customs, and traditions like India makes it more challenging to accomplish sustainable development in a country that is rapidly industrialising and improving its standard of living. Although there have been substantial changes in the social, economic, and environmental spheres, India’s SWM systems have mostly remained the same. Currently, 90% of residual waste is thrown in the informal sector rather than properly disposed of. To make SWM more sustainable, new management practises and disposal sites are needed. The inefficiency of the current waste management systems has a detrimental effect on the economy, the environment, and public health. The Ministry of Environment and Forests of India introduced regulations for garbage treatment, although there is irregular and insufficient compliance.

In meteorology, we often use some of the physical parameters to explain the physical processes taking place in the atmosphere. These parameters must have already appeared in the earlier chapters. However, these are given in this chapter to enable the readers to get acquainted once again.

16.1 Momentum

Momentum is defined as the product of mass and its velocity. In S.I. system units mass is expressed in kilograms and velocity in meters per second.

Momentum = Mass x Velocity

Units for momentum (S.I. system) = kg. m/sec

In C.G.S. System, mass is expressed in grams and velocity in cm/sec.

Units for momentum (C.G.S System) = gm.cm/sec