eChapters

Abstract

The landslides of the hill ecosystems are either due to the natural morphotectonic and morphodynamics processes of the planet earth or due to the anthropogenic effects or due to the combinations of the both. In the Indian subcontinent, the landslides are reported from three major provinces viz: Himalayas, Westernghats and The Nilgiris. While the landslides of the Himalayas are demonstrated to be predominantly due to active tectonics, the landslides of the Westernghats are attributed to excessive weathering and rock fall. On the contrary the landslides of the Nilgiris have been thought to be due to extensive deforestation and the related increase in the pore pressure during rainy seasons. But the studies carried out in the recent years show that not only in the Nilgiris but also in other hill systems of Tamil Nadu, the landslides seem to be related to the recent earth movements. This is very significant in the context of fastly recurring seismicities in South India and hence this aspect warrants detailed studies for landslide mitigation.

Abstract

The analysis of IRS - 1A satellite imagery has indicated the existence of two NE - SW trending sub parallel faults along which the coast is undergoing land subsidence as revealed by the concavity in the shore line, preferential migration of the river systems and the drainage congestion, absence of beach ridges, occurrence of off shore shoal etc. The study has further indicated chains of tectonically induced environmental problems such as ground water logging, coastal zone flooding, storm surges, harbour sedimentation etc.

INTRODUCTION

Coastal zones are always dynamic and active, because of the multivariate morpho tectonic and morpho dynamic processes, viz: tectonic, fluvial, marine and aeolian which act in varying degrees and duration along the coasts. As these geomorphic / morpho dynamic processes act in varying permutations and combinations in different segments of the coasts, the land - ocean interactive phenomenon vary greatly in time and space, which in turn frequently and dynamically alter the coastal environment, and cause fragility to the coastal ecosystems. Further, as the coastal zones act as the junction between the Continents and the oceans, even mild earth movements exhibit exemplified expressions in land - water distribution pattern along the coasts. The green house effect and the much apprehended sea level rise and the disasters like cyclones also contribute in their own way in accelerating such land - water distribution / land - ocean interactive phenomenon.

OBSERVATION

The examination of the IRS - 1A imagery under raw and the digitally enhanced modes vividly display heavy concentration of suspended sediments in certain sectors along the east coast of Tamil Nadu. Such pockets of suspended sediments are seen as long and linear bodies trending parallel to the coast to the strike length of 20 - 30 km and width of 5 - 10 km. Such Phenomenon of suspended sediments concentration are strikingly observed in two sectors. One in between Tuticorin harbour and Vaippar river mouth and the other just at the mouth of Ponnaiyar river along Cuddalore-Pondicherry coast. Both of them are observed along conspicuous (Fig.1& 2) concave coasts.

The resources on the land have started showing sign of faster depletion owing to the population explosion, over exploitation of mineral and water resources and also the improper exploitation and the related wasting of the natural resources. Hence a time has come to search for more and more newer natural resources amongst which the ocean resources gain supreme importance as this treasure is yet to be hunted due to the non - availability of suitable technology for the same.

Such ocean resources mainly include the mineralogical and biological resources. The ocean biological resources, their birth, growth, population and migration greatly depend as chlorophyll content, total dissolved oxygen, total suspended solids, salinity etc. These parameters which constitute the marine environment drastically change in a quick span of time owing to the dynamically changing marine forces.

Abstract

The present study has revealed that the NE-SW and WNW-ESE trending sinistral faults are very active along the Tamil Nadu coast and the same have caused considerable slope modifications along the Coleroon and Karungalar rivers which are well-manifested in the land, water and mudflat distribution pattern. Similarly, the progradation of the land in Vedaranniam nose is due to the rise of Pattukottai-Mannargudi area and the time transgressive modifications of the Vedaranniam backwater indicates the opening up of the N-S trending Pleistocene-Holocene faults.

Abstract

The art of remote sensing has opened up many vistas in the study of river migration as satellite photographs, both in their normal and digitally enhanced modes, vividly show the rivers and their migratory signatures. The rivers migrate for various reasons amongst which tectonic movement is one of the main causes. In the present study an attempt has been made to exhibit the palaeochannel network of the rivers of Western India and integrate them with lineament fabric, so as to understand the Quaternary tectonics of the region. The study has shown that Western India shows considerable signs of Quaternary tectonics.

The great Indian epic ‘Ramayana’ says that ‘Lord Rama’ has tried to cross over the Bay of Bengal so as to reach Sri Lanka from India from three points along the southeastern fringe of the Indian coast. Firstly, he is said to have tried to cross from Vedaranniyam which is mythologically called as ‘Kodiyakkarai’ Secondly from Manamelkudi and finally crossed over to Sri Lanka from Rameswaram Island (Fig.1), as the former two coastal locations were widely separated from Sri Lanka by Bay of Bengal and the Rameswaram Island was nearer to Sri Lanka during that period. But, the recently acquired satellite data shows the huge accretion of sediments and rapid land building activity off Vedaranniyam coast (Fig. 2 and 3). The geomorphic interpretations carried out using IRS 1A imagery and 14^C archaeological dating of such geomorphic features have shown that such ongoing sediment accretion phenomena off vedaranniyam nose might in future connect the Vedaranniyam part of Indian Peninsula with Jaffna Peninsula of Sri Lanka if the sediment accumulation continues unabated. The sediment accretion in this area, therefore, requires detailed studies particularly in the context of the coastal ecosystem (Fig. 1).

Abstract

The Remote Sensing and the followed up field based investigations show that the Tamil Nadu coast, India, is facing series of geoenvironmental problems due to tectonic movements and morphodynamic processes. Such problems pose a challenge to the engineering geologists. The paper discusses such challenging engineering geological problems and plausible remedial measures.

Abstract

The tectonic and the geomorphic features observed along the west coast of the area between Mangalore and Cape Comorin show that the NNW-SSE trending west coast has been carved out by the Western Ghats orogeny and the related NNW-SSE trending release fractures. The sinuosity of the otherwise straight coast line is due to Quaternary cymatogenic arching caused by the thrust related to the northerly movement of the Indian plate. The coast line has further attained peaks, projections and serrations due to the ENE-WSW trending series of Precambrian extension fractures which were reactivated gaining the northeasterly directed forces from the rising Carlsberg ridge. Overall, the west coast is being tectonically evolved even today due to the rise of Carlsberg ridge and the Indian plate movement.

Abstract

There is a consensus amongst the geoscientists that overall there has been progradation along the east and west coasts of peninsular India. However, the present day configuration of the coasts and some of the geomorphologic features such as absence of spit and delta along west coast and absence of major estuaries and petroliferous structures along east coast still remain controversial. The present study, based on the appreciation of certain geomorphological and tectonic features on Landsat imagery and aerial photographs of southern part of Indian Peninsula, suggests that the evolution of the coastline has been mainly controlled by tectonism.

The tapering nature of the coastline is attributed to the Precambrian orographic axis. The serrated nature of the post Precambrian coast line is due to the Precambrian transverse faults, whereas the serrated margin of the post Gondwana, Post cretaceous and post Tertiary coast lines are attributed once again to the Precambrian faults reactivated time and again. During the Quaternary period the coast line has undergone many modifications. The coast line attained sinuosity due to Pleistocene folding which is well manifested by river migration. The coast line was subsequently faulted and shifted with en echelon pattern due to N-S regional compression which is referable to the collision of Indian Plate with Tibetan plate.

Remote sensing has proved its credibility beyond doubt in natural resources survey and environmental monitoring owing to its synoptivity, multispectral photographic capability and repetitive coverage. While its synoptivity gives unbiased information on the regional panorama of the earth surface, its multispectral possibility aids precise interpretation of various objects, as different terrestrial objects exhibit various spectral responses in different bands of the electromagnetic spectrum. Amongst various terrestrial objects, water has a characteristic spectral response of its own, i.e. it permits the blue / red part of EMR (electromagnetic radiation, 0.4-0.8 µm) to penetrate inside. On the contrary, it totally absorbs the infrared part of EMR (0.8-1.5 µm). As such blue/red part of EMR penetrates the water bodies, the impurities and suspended sediments are seen very clearly in various shades of gray as and when the water bodies are shallow. Many workers, therefore, have used blue / red band of the satellite data in such water-quality studies^l-3. Hardy⁴ has observed that the infrared light in the spectral regions of 0.6-1.4 µm has the potential to map the turbidity in the ocean water, whereas Kritakos et al ⁵ have used the rationed data of visible and near infrared bands (0.4-1.1 µm) and obtained better results for water quality monitoring. Keeping such facts in mind, the blue/red band (band 2) of the IRS 1A satellite data was used to configurate the bathymetry along Madras coast in Bay of Bengal (Figure 1 a).

In the present study, the IRS lA band 2 data (0.52-0.59 µm) of March 1991 was used and subjected to edge enhancement studies for the coastal zone of Madras (Figure 1 a). Such edge enhancement normally sharpens the edges of two contrasting objects or sharpens the edges of objects of contrasting relief. In such edge enhanced data, few

Abstract

The East Coast of Tamil Nadu exhibits a spectacular network of deltas formed by the easterly flowing river systems. The study of raw and digitally enhanced Landsat TM and IRS data shows, that these deltas were formed due to multivariate dynamic processes of fluvial, marine and aeolian actions. The wide fan shaped delta observed northwest and north of Madras city spanning out over an area of 700 sq.km is a feature, standing testimony to the PaleoCauvery river systems.

The regional slope and the overall arcuate arrangement of the crescent shaped lakes in the area and the tentacles of paleochannels show, that it is overall a fan shaped delta and its successive growth towards the sea might have been due to the constant progradation of lobes by continuous reworking of preceding lobes. The depressions in between successive concentric lobes have become the lakes. The absence of any beach ridges in such palaeo deltaic regime suggests that, it would be a sub aerial delta only. The overall arcuate shape of the shoreline in between Madras city in the south and Pulicat lake in the north is due to this fan delta. This feature once again symbolises the active river dominated delta. The Palar delta is a ‘cuspate’ one. The Ponnaiyar river has developed a linear delta, along a narrow depression found in between Tertiary uplands. While the avulsion phenomenon indicates the ancient shoreline near Villupuram, the east-west trending micro sandy uplands within the delta suggest, that it is a tide dominated delta.

Abstract

Satellite photographs depict exciting evidence on the migratory melodrama of river systems. A study has been conduced in parts of Tamil Nadu using IRS-IA Satellite pictures, archaeology and Tamil literature, which reveals that from Pleistocene to 2700 years B.P.(Before Present) the river Cauvery flowed in a northeasterly direction from the Stanley reservoir via Chinnar, Palakkodu, Mattur, Tiruppathur (Tiruppattur), Gudiyatham (Gudiyattam), Vellore and Walajapet to meet the sea at Madras. From 2700 to 2300 years B.P., it flowed via Uttangarai and Tirukkovilur to meet the bay of Bengal near Pondicherry, over which the present-day Ponnaiyar is a misfit stream . From 2300 to 1300 year B.P. it has flowed via Erode, Tirukkampuliyur, Alagarai , Tiruchy, Kiranur and Pudukkottai meeting the sea in the region where the present-day Agniar and Ambuliar meet the sea. Subsequently, between 1600 and 1300 years B.P., the Cauvery flowed along the present-day tracts of the Vennar and Vettar, after which it seems to have flowed as the Kodamurutti, Arasalar and PalanCauvery from 1300 to 1000 years B.P. From about 900 years B.P. it flowed via Tirupurampayam (Tirupurambiyam), Achalpuram till around 750 years B.P. and then it is stabilised as the Colleroon (Kollidam). Such periods and phases of river migration as well as their implications in the search for archaeological remains are discussed in this paper.

Much has been talked about the mighty river systems and their migratory histories, since Purana and Vedic times. In Mahabharata the places where the Lord Krishna is said to have played with Gopis in the banks of River Yamuna are now forming flat lands many kilometers away from the present day Yamuna. In the same way, there is a mention in ancient literature about the ‘Indo-Brahm’ river which was originated from the Himalayas and flown through Brahmaputra valley, Indo-Gangetic plains, Rajasthan desert and met the Arabian Sea in Rann of Kutch. Such a mighty river is said to have fragmented into Brahmaputra, Ganges and the Indus rivers due to Tectonic activity in Himalayan regions. Similarly there are many evidences in the Tamil literature. For example in ‘Kalingathuparani’ it is mentioned that the river ‘Palar’ was flowing north of Kanchipuram but the same river is now flowing south of it.

All these facts show that the rivers have the tendency to frequently change their courses. The advent of modern Remote Sensing Technology has opened up new vistas in studying such migratory rhythms of the rivers, as such old and buried rivers exhibit spectacular ribbon like, linear, curvilinear and contorted features with typical darker tone in black and white images and reddish tone in false color composites (FCC) and other color coded images.

Abstract

The art of remote sensing has opened up many vistas in the study of river migration as satellite photographs, both in their normal and digitally enhanced modes, vividly show the rivers and their migratory signatures. The rivers migrate for various reasons amongst which tectonic movement is one of the main causes. In the present study an attempt has been made to exhibit the palaeochannel network of the rivers of Western India and integrate them with lineament fabric, so as to understand the Quaternary tectonics of the region. The study has shown that Western India shows considerable signs of Quaternary tectonics.

Abstract

The anomalies observed in the reverine systems have been demonstrated to be the potential tool in deciphering the tectonically active zones. Such various drainage anomalies viz: radial drainages, anomalous compressed meanders, eyed drainage and the youthful floodplains observed in Annamali – Palani - Varushanad hill ranges of the Western Ghats of Tamil Nadu show that the N-S and NE-SW trending faults are tectonically active in the recent years.

Abstract

It has been established beyond doubt that the drainage architecture and the fluvial histories of river systems give excellent indications not only on the surficial lithology but also on the ongoing morphotectonic processes of the planet earth. Among the various drainage patterns, the ‘eyed drainage’ pattern is considered to be one of the most significant anomalies and such ‘mega eyed’ drainages interpreted from IRS-IA imagery in some of the major river systems in Tamil Nadu, Indian Peninsula, are found to signify ongoing tectonic movements in an otherwise seismically inert shield area.

Abstract

Satellite imagery interpretation has shown the existence of a major Palaeochannel system in the Great Indian desert. These palaeochannels belong to the mythological Sarasvati river, which seems to have flowed southwesterly close to the Aravalli hill ranges and joined the sea in the Great Rann of Kutch. Subsequently it seems to have shifted northwesterly, and more precisely in an anti-clockwise direction and got buried in the desert in Anupgarh plains. While its oldest course is the now misfit Luni river, its final trace is now represented by Ghaggar river. Whereas its overall northwesterly migration is attributed to NE-SW trending cymatogenic arching along the Great Rann of Kutch in the southwest to the Siwalik hills in the northeast, its multivariate palaeodrainage is attributed to block faulting and land subsidence in the Bikaner sector.

Abstract

The recent earth movements and the related seismicities in the Southern part of the Indian Peninsula has been a matter of enigma for a century and more. While one school was strongly holding the opinion that the southern Indian Peninsula is free from recent earth movements as it is a shield area, the other school has narrated the possibilities for the ongoing earth movements. Under these circumstances, the various anomalies observed from satellite data and ground based information on geomorphology, subsurface lithology, geophysics, hydrogeology, geochemistry etc. have suggested a possible Pleistocene / Holocene graben along Pondicherry in the northeast and Cumbum Valley in the southwest in the southern tip of the Indian Peninsula.

The geologists of the Indian subcontinent have all along been of the opinion, that, the southern part of the Indian Peninsula is a stable shield area. But, the recently acquired IRS-1A image of June, 1988 vividly displays spectacular geomorphic anomalies suggesting that this part of the Indian subcontinent is prone to earth movements. In order to unearth more evidences on such earth movements / neotectonism in Tamil Nadu, the IRS-1A image of Coromandel coast of Tamil Nadu was analysed ( Fig. 1).

OBSERVATIONS

• The IRS-1A image conspicuously displays three contrasting morphotectonic domains in the study area marked by the western undissected Tertiary upland (Vallam upland), central highly dissected Tertiary upland (Pattukottai -Mannargudi upland) and the eastern Cauvery delta (Fig 1 and 2). These three domains are separated by two conspicuous N-S trending lineaments (E and F, Fig.1 and 2) namely the Tanjavur - Avadaiyarkovil lineament in the west and Kumbakonam -Muttupet lineament in the east.
• In addition, two more E-W trending lineaments (G and H, Fig.1 and 2) are also observed trifurcating the undissected Vallam upland into three blocks.
• Along these lineaments, especially the Tanjavur -Avadaiyarkovil and Kumbakonam -Muttupet lineaments, the rivers show conspicuous drainage anomalies in the form of drainage deflection, drainage compression etc., wherever they transect the lineaments.

Abstract

The southern part of the Indian Peninsula has long been regarded as a stable area free from Pleistocene tectonics as it represents the Precambrian shield region. But the frequent earth tremors even up to a magnitude of 6.5 (Richter scale) which occurred in Tamil Nadu have started encouraging the geologists to think that it could possibly be a seismic prone zone. In addition, images acquired by the polar orbiting satellites offered valuable information on the fracture systems and fluvial anomalies suggesting possible Pleistocene tectonism in South India. Hence, a study has been undertaken to evaluate the signatures of Pleistocene tectonism in South India using IRS-lA, LISS-1 FCC imagery (Indian Remote Sensing Satellite lA, Linear Imaging Self Scanning 1, False Colour Composite) involving band 2, 3 and 4 under blue, green and red bands respectively.

The study has brought out a series of E-W trending cymatogenic arches and N-S trending extension, NE-SW trending sinistral, NW-SE trending dextral and E-W trending release fractures with characteristic signatures supporting Pleistocene tectonism in Tamil Nadu and Kerala.

On the basis of such morphotectonic features, a Pleistocene tectonic model has been presented with a N-S trending greatest principal stress and an E-W oriented least principal stress related to the movement of the Indian plate towards the Tibetan plate. Based on the model developed for Tamil Nadu and Kerala, a series of E-W trending cymatogenic arches and deeps have been proposed for Cochin- Rameswaram in the south to the Himalayas in the north. Further studies for seismotectonics, geothermal resources and hydrocarbon search have also been suggested along such arches and deeps.

Abstract

The tectonics of the geological past from Archaeozoic to early part of Cenozoic era has been studied due to their penetrative documentation in the form of folds and faults. But the tectonic history of the latter part of the Cenozoic era (i.e Pleistocene period) has remained a matter of conjecture owing to the poor response of the rocks to Pleistocene movements. In the present study the authors presented a model for the Pleistocene earth movements of South India through the study of river migration, coast line changes and lineament fabric derived from the space borne photographs.

In the area of study, the northerly migration of Paleru and Pennar and southerly shift of Palar, Ponnaiyar and Cauvery rivers, marine regressions restricted within this segment and the closely spaced crest line fractures suggest a lineament controlled E-W trending Quaternary upwarping along Mangalore-Madras alignment. Similar E-W cymatogeny is inferred in the southern tip of the Peninsular India on the basis of once again such observations. Such E-W trending Pleistocene arching phenomenon suggests a N-S oriented regional compression which could be related to the collision of Indian plate with Tibetan plate.

16.1 Introduction

It is well known fact that planners as well as end user’s have to consider any resources as technology from economic point of view. Therefore, it is important to have techno – economic analysis of each energy source option. In the feasibility study of particular energy option, three tier judgement approaches is required, which include technical feasibility, economical viability and social acceptability. Hence in the rural energy planning programme one has to considered techno socio economic analysis of an individual energy option. Since in integrated rural energy planning, locally available energy resources are used, presuming that it is socially recognized. Hence in the IRPE project, the need and scope of techno economic analysis in terms of economic analysis of different technical feasible options, before between “economic” and “financial” analysis should be kept in mind. An economic analysis is needed to verify that a particular energy source will provide “net benefit” to society as a whole, before its final integration in the energy context, while a financial analysis integrated in the energy practices. In simple wards, a financial analysis is concerned with goods and services, money inflow and outflows and the transfer of payments. An economic analysis also considers the social benefits and costs of goods and services which are not traded in a market.

15.1 Fuel Cell

Fuel cell is a electrochemical device that convert chemical energy of a reaction directly into electrical energy. The basic physical structure of a fuel cell consists of an electrolyte layer in contact with a porous anode and cathode on either side. A schematic representation of a fuel cell with the reactant or product gases and the ion conduction flow directions through the cell is shown in Fig. 15.1

14.1 Introduction

Indoor air pollution causes significant health problems for the two billion people worldwide who rely on biomass fuels for their cooking and heating needs. Over the last 30 years awareness of the environmental and social costs of using traditional fuels and stoves has grown. At the same time, studies of the problem have resulted in proven strategies to reduce both fuel use and harmful emissions. Unfortunately, the local stoves currently available do not always represent the best designs that modern engineering can offer. Although open fires are often used wastefully, carefully operated open fires can be fuel efficient and clean burning when tested in the lab. In many situations, cooks are not overly concerned with fuel use, and studies have shown that when fuel is plentiful three-stone fires can use an excessive amount of wood to cook a small amount of food. But in other places where fuel is scarce, open fires can be carefully controlled so that fuel efficiency rivals many first generation improved cook stoves.

Modern cook stoves are designed to clean up combustion first. Then the hot gases can be forced to contact the pot and increasing efficiency without increasing harmful emissions. Fires can be clean burning when expert cooks push the sticks of wood into the fire as they burn, metering the fuel. The open fire can be a hot fire useful when food or drink needs to be prepared quickly. The energy goes into the pot, not into the cold body of a stove. The open fire can burn wood without making a lot of smoke; hot fires burn smoke as it is released from the wood (Fig.14.1). Unfortunately however, many fires used for cooking are built emphasizing simplicity of use and are wasteful and polluting. Modern stoves score higher when tested than even the most carefully operated fire in the laboratory.

13.1 Introduction

Winds are the motion of air around the earth. This movement in air is caused by the uneven heating of the planet’s surface by the sun. The idea of using wind as a form of power is not new. The traditional applications of wind were primarily as sources of kinetic energy for rural, agricultural and a limited number of industrial uses such as pumping water and grinding grain.

Presently wind energy can be used for two major applications, such as wind mills for pumping water for drinking as well as for irrigation purposes and second application is as aero-generator for electricity generation for domestic and industrial uses. In addition to this, presently wind energy battery charger are also available, which can store energy for lights, radio communication, hospital equipment and to power various emergency related equipment.

The wind energy has an enormous resource, but the problems of utilizing the winds are many and varied. Wind energy is very diffuse in nature and local topographical features significantly alter the prevailing winds thus leading to the extremely site specific nature of wind energy.

Scientirsts have estimated that as much as 10 per cent of >the world’s electricity could be provided by wind generators by the middle of 21 century. India has estimated wind power potential of 45,000 MW. India now, ranks fourth in the world in wind power generation.

The world’s largest wind farms are in California, where wind turbines can generate power upto about 1120 MW. The first wind mill used as source of electric power was built in Denmark in 1890. Presently in India about 2382 MW of electricity is being produced through wind energy.

12.1 Introduction

Nature has a provision for destroying and disposing off wastes and dead plants and animals. This decay or decomposition is carried out by tiny micro-organisms called bacteria. Making of farm-yard manure (FYM) and compost is also through decomposition of organic matter (OM). When a heap of vegetable or animal waste and weeds etc., die or decompose at the bottom of backwater or shallow lagoons, bubbles can be noticed rising to the surface of water. Sometimes these bubbles burn with dancing flame at dusk. This phenomenon has puzzled man for a long time. It was only during the past hundred years that Scientists unlocked this secret as the decomposition process. The gas thus produced was and is still called “Marsh Gas.” The technology of harnessing this gas under artificially created conditions is known as Biogas Technology.

11.1 Biodiesel Chemistry

Biodiesel is a mixture of methyl esters of long chain fatty acids like lauric, palmitic, stearic, oleic and so on. It is produced by the transesterification of animal fats and vegetable oils – all of which belong to a group of organic esters called triglycerides. Typical examples are rape/canola oil, soyabean oil, sunflower oil, palm oil and its derivatives, etc. from vegetable sources, beef and sheep tallow and poultry oil from animal sources and also from used cooking oil. The chemistry is basically the same irrespective of the feedstock. The chemistry of biodiesel is given in Fig. 11.1.

10.1 General

The term “biomass” generally refers to renewable organic matter generated by plants through photosynthesis. Materials having organic combustible matter is also referred under biomass.

Biomass is an important fuel source in our overall energy scenario. Biomass is produced through chemical storage of solar energy in plants and other organic matter as a result of photosynthesis. During this process conversion of solar energy in sugar and starch, which are energy rich compounds takes place. The chemical reaction of photosynthesis can be written as:

9.1 Introduction

Solar energy can be directly converted into electrical energy through photovoltaic route. Energy conversion devices which are used to convert sun light into electricity by use of the photovoltaic effect are called solar cells. The advantages of solar cells are:

1. They are reliable, convenient and durable.
2. It is green, sustainable and pollution free technology.
3. Directly solar radiation can be converted into electricity (conversion of global solar light by flat plate photovoltaic).
4. Maintenance cost is quite low therefore suitable even in isolated and remote area, since no moving parts are involved.
5. Solar cells are quite compatible with almost all environments, respond instantaneously with solar radiation.
6. Considerable expected lifetime i.e. 20 years or even more.
7. No distribution system is required, because they are decentralized source of energy and located at the place of use.

8.1 Introduction

The concept of social justice led to a raise the standard of living of the masses. This is only possible by meeting the energy needs of industry, agriculture, transport and domestic use. The energy of demand has been increasing tremendously all over the world science mid – nineteenth century due to rise in industrial and agricultural activities and was being met to a great extent by fossil fuels.

Three factors led the mankind to look for alternative renewable sources of energy like solar, wind, hydro etc. (1) there is a danger that the rate at which the non renewable sources of energies are being consumed presently may lead to a global shortage in the near future. This has already happen in case of oil. (2) Use of fossil fuel involves emission of toxic gases polluting the environment causing health hazards of living being. and (3) the demand and supply gas of energy is continuously widening, thus necessitating to exploit renewable sources of energy.

Out of various renewable energy sources, solar energy has been a promising one and lot of development has been taken in its technology for various uses. The numbers of technology engaged in developing solar energy for meaningful use are aiming to achieve the following objectives-

7.1 Introduction

Energy has become a critical input for the economic development of the India because of the wide spread scarcity of oil and electricity and other commercial form of energy.

The rural areas are often the worst affected because of these shortages and the rural population continues to depend on the inefficient non-commercial energy from like fire wood, cow dung, human and animal for meeting their energy requirement for subsistence, production and devolvement needs.

The rural energy crises or “The energy crisis” has been getting increased attention from the policy makers to tackle the problem in a planned and integrated manner.

The rural energy sector is concerned with two major planning issues.

1. Provision of energy for meeting substance needs for cooking, heating and lighting of the rural areas of the country. This problem is also directly linked to the problem of deforestation and environmental destruction being caused in the rural area because of indiscriminate and wide spread use of non conventional energy sources.
2. Meeting energy requirements for production activities which would create employment and productivity in rural areas.

6.1 Introduction

Energy planning is possible only with knowledge of past and present energy consumption and future energy demand. There are number of factor which affects the energy consumption pattern significantly. These include energy prices, availability, reliability of supply, uniformity of quality, convenience in use, technical and economic characteristics of energy using equipment & appliances, population growth, income rate of urbanization, educational status, social acceptance, social habit, present knowledge of beneficiary etc.

The energy planning differ in planning sectral wise and planning sources wise. For sector planning purposes, estimates are needed of the short and long run price elasticity for every specific energy resource. Where as in planning sources wise, one must consider its long term availability & its costs.

In general, to cope up future risk and uncertainty, we need to predict the future event. The likely future event has to be given from and content in terms of projected course of variables i.e. the forecasting. Projection is of two types – forward & backward. It is the forward projection of data variable, which is named as forecasting.

These three requirements are required to be followed in sequence for getting maximum benefits. However, integrated rural energy concept is a new area of work and not much experience is available in this field as compared to other rural development activities. It is difficult to give any guidelines for planning. One can only recommend approaches and not solutions to planning.

The rural area in developing countries are almost always rich in one or another sources of energy, which could be used separately or in combination with other sources in decentralized small scale units, or even on a household scale. Thus, the problem is one of good planning, management and a strong educational and promotions campaign, rather than the non availability of resources or the lack of technology. Further, after planning, prefect development of device and their effective operation is required.

The purpose of the Integrated Rural Energy Planning project should be clearly defined. It may design either for research and development or demonstration for Popularisation of system, education and training, promotion, health or combination of these.

It is usually better to start with a small size to gain experience and build up confidence before undertaking the large scale project. As defined earlier, one of primary requirement of Integrated Rural Energy Planning is to develop energy demand pattern, energy supply system and optimally match demand with supply.

4.1 Introduction

The energy census survey has become the basis for planning & implementation of the village development based on conventional and non conventional sources which are appropriate to the local needs. The continuous and widespread use of non commercial sources of energy in the rural area is resulting in the large scale destruction of the environment. While the rural people get non conventional fuels at almost zero private cost, the social cost for meeting their energy needs has been increasing over the year. Hence the non conventional fuels acquired a special significance in the energy context.

The rural energy problem is multi dimensional & needs to be tackled through a multi dimensional integrated approach which would include augmentation of energy supply resources, technology transfer for optimum & productive use of resources, R & D inputs in particular for developing low cost energy options for the rural poor, education & training for rural users, linkage with various rural development programmes including village & small scale industries programme and adequate institutional & financial support. The multi dimensional approach for making a village self sufficient in energy planning is illustrated in Fig.4.1.

3.1 Introduction

There is now latest national thinking going on to conserve the known sources of energy such as firewood, cow dung, agricultural waste, kerosene, oil etc. i.e. by limiting their conventional uses and to propagate the use of non conventional energy especially in the rural area. The large scale indiscriminate use of non commercial fuels fully in the rural areas are not only providing to be inefficient but also inadequate to cope with the growing rural energy demand caused by growing population and growing consciousness among rural people for a better way of life. Planned input of energy are, therefore urgently require to protect the environment and to cope with raising rural energy demand. In order to assess the widening gap between the supply and demand of commercial energy and indiscriminate use of non commercial fuels in rural areas, there is a need for various types of statistical or quantified information to be collected and analyzed in an objective manner and presented suitability so as to serve as a sound basis for taking policy decision to make an optimum utilization of commercial energy in a balanced manner. This will require conducting of survey in areas to be covered.

The statistical data may be collected by complete enumeration or by a sample survey. The earlier method is very cumbersome, time consuming, cost ineffective and requires an intensive development of manpower, if domains of study is quite large. Complete enumeration and sample surveys presuppose the existence of a certain minimum of facilities such as funds, professional personnel for planning the survey methodology and supervision of field operations, sufficiently qualified enumerators, sampling frames, machine tabulation equipment, transport and communication facilities etc. These facilities or combinations there of do not always exist to the extent needed for a complete enumeration survey. As such, sample survey is preferred to complete enumeration for ethic type of studies giving due importance to sampling error.

In the integrated energy planning, there is an objective to find out the present consumption pattern of energy for different end uses, shortages being experienced and people’s reaction to using alternate sources of energy is also enumerated.

The survey methods determine – incident, distribution and the interrelation among sociological variable and psychological variable. The sociological variable s consists of age, education, income and attitude, behavior, motivation, belief and knowledge about the problem.

2.1 Introduction

Energy is one of the main input for rural development and economic development. The greater part of the world population lives at low standard and a quarter of the population or about 1.5 billion, have an extremely low standard of life. Energy is one of the essential requirement of the quality of life the people. The industrial development or even large scale food production, water supply, textile manufactures & construction of building and other recreation items are not possible without adequate supply of energy. Therefore, one of the most important tasks is to provide adequate, reliable, convenient and efficient supply of energy, if quality of life of the people is to be raised from its present level of grinding poverty. Table 2.1 project the global primary energy supply in six scenarios i.e A1 - its strong emphasis on oil and natural gas use. A2 - which is coal-intensive. A3 - which emphasises the roles of natural gas, new renewables and nuclear in averting serious problems from emissions. B - Middle course. C1- with its emphasis on energy efficiency improvements, new renewables (especially solar in the longer run), but with nuclear power phased out by 2100 because unable to satisfy its critics and C2 - where nuclear power plays an expanding role.

1.1 General

Access to energy is a crucial enabling condition for achieving sustainable development. Prudent energy policies and research can play an important role in steering both industrialized and developing countries onto more sustainable energy development paths. Specifically, they can strengthen the three pillars of sustainable development: the economy, by boosting productivity, social welfare, by improving living standards and enhancing safety and security, and the environment, by reducing indoor and outdoor pollution and remediating environmental degradation.

1.2 Energy and it’s Requirement

Energy in any form is necessary to meet many of our requirements. It’s varying definitions shows the importance of energy in our life.

The science of agrometeorology has great practical utility in protection against, or avoidance of adverse climate risks of crop production. Agrometeorological information can be used in efficient land use planning, determining suitable crops for a region, risk analysis of climate hazards and profit calculations in farming, production and harvest forecasts, and in adoption of farming methods and choice of farm machinery. Meteorological instruments are the equipments used to sample the state of the atmosphere at a given time. Meteorology does not use much laboratory equipments but relies more on field-mode in situ observation and remote sensing equipments. Rain was one of the first weather parameter to be measured historically. Two other accurately measured weather-related variables are wind and humidity.

An agrometeorological observatory or station is a place where all the necessary instruments and structures are installed and maintained to observe and record the weather parameters at stipulated time interval.

Climate, soil, input and management factors influence the crop yield. Weather is the most important natural input that affects the agricultural production and productivity. The agricultural activities starting from the land preparation to harvest and post-harvest storage are greatly influenced by the weather. The effects of weather on crops may be direct such as those of precipitation, solar radiation, humidity, temperature, etc., or indirect such as those of pest, diseases, weed competition, etc. Thus, the success or failure of a crop is determined by the prevailing weather conditions. Although influence of weather conditions on yield is well established, the quantitative assessment is not always straight forward and simple. The quantitative assessment of the effect of weather on crops is an important application of agrometeorology. The relationship between weather and crop production has been understood through crop weather modelling and study on this aspect through a systematic approach started a century ago. The aim of developing crop weather models is to ensure better utilisation of resources and hence a more environmental friendly and sustainable agriculture.

A model is a schematic representation of the conception of a system or an act of mimicry or a set of equations, which represents the behaviour of a system. Its purpose is usually to aid in explaining, understanding or improving performance of a system. Agricultural models are mathematical equations that represent the reactions occurring within the plant and the interactions between the plant and its environment. However, it is a difficult task to represent any system completely in mathematical terms because of the complexity of the system. Universal models do not exist for the agricultural systems and agricultural models are built for specific purposes and the level of complexity is accordingly adopted. Different models are developed for different subsystems and several models may be built to simulate a particular crop or a particular aspect of the production system. Crop weather models may be defined as a simplified representation of the complex relationships between weather or climate on one hand and crop performance such as growth, yield or yield components, on the other hand by using mathematical and/or statistical techniques

The word ‘remote sensing’ was coined by Evelyn L. Pruitt, an American Geographer in 1960. Remote sensing is defined as collection and interpretation of information about a target without being in physical contact with it. Remote sensing is the science and art of obtaining information about an object, area or phenomenon through the analysis of data acquired by a device that is not in contact with the object, area or phenomenon under investigation (Lillesand and Keifer, 1994).

The information needs a physical carrier to travel from the objects/events to the sensors through an intervening medium. Any force field such as gravity, magnetic or electromagnetic could be used for remote sensing. However, the electromagnetic radiation is conventionally used as an information carrier in remote sensing. Remotely sensed data may be gathered by different devices, including sensors, film cameras, digital cameras and video recorders. Instruments capable of measuring electromagnetic radiation are called sensors.

Remote sensing is nothing but opposite of astronomy. In astronomy, man looks from the earth to the sky to understand and gain more knowledge about the celestial objects. But remote sensing refers to going upward in the sky to look downwards to understand and gain more knowledge about terrestrial objects. In remote sensing, the aerial sensor technologies are used to detect and classify objects on earth by means of electromagnetic radiation.

Weather forecasting is the application of science and technology to predict the state of the atmosphere for a given location. Weather forecasts are made by collecting quantitative data about the past and current state of the atmosphere on a given place and using scientific understanding of atmospheric processes to project how the atmosphere will evolve on that place. Weather warnings are important forecasts because they are used to protect life and property. Forecasts based on temperature and precipitation is important to agriculture.

Agricultural production is highly dependent on weather, climate and water availability, and is adversely affected by weather and climate related disasters. In many developing countries where rainfed agriculture is the norm, a good rainy season means good crop production, enhanced food security and a healthy economy. Failure of rains and occurrence of natural disasters such as floods and droughts can lead to crop failures, food insecurity, famine, loss of property and life, mass migration, and negative national economic growth (Sivakumar, 2006).

Farming in many parts of the world, especially in the arid and semiarid regions is risky, because climate is highly variable. In some developing countries as much as 80% of the variability in agricultural production is due to the variability in weather conditions. This production variability in agriculture has immediate and important macroeconomic impacts. A timely seasonal forecast of favourable conditions could permit farmers to adjust cropping patterns and input use in order to benefit fully from these conditions. Also, a timely forecast could give the marketing system and downstream users, such as the food processing industry, time to prepare for a bountiful harvest (Arndt et al., 2000). It is important to remember that under rainfed conditions, even a less reliable, but earlier forecast may be more valuable than an accurate but late forecast (Mjelde et al., 1998).

Many aspects of the global climate are changing rapidly. Evidence for changes in the climate system abounds, from the top of the atmosphere to the depths of the oceans. The climate system is the highly complex system consisting of five major components; the atmosphere, the hydrosphere, the cryosphere, the land surface and the biosphere, and the interactions among them. The climate system evolves in time under the influence of its own internal dynamics and because of external forcings such as volcanic eruptions, solar variations and human-induced forcings such as the changing composition of the atmosphere and land-use.

The term ‘climate variability’ is often used to denote deviations of climatic statistics over a given period of time (e.g., a month, season or year) from the long-term statistics relating to the corresponding calendar period. In this sense, climate variability is measured by those deviations, which are usually termed anomalies.

‘Climate change’ refers to a statistically significant variation in either the mean state of the climate or in its variability, persisting for an extended period (typically decades or longer). Climate change may be due to natural internal processes or external forcings, or due to persistent anthropogenic changes in the composition of the atmosphere or in land use. The United Nation’s Framework Convention on Climate Change (UNFCCC) defines ‘climate change’ as ‘a change of climate behaviour which is attributed directly or indirectly to human activity that alters the composition of the global atmosphere and which is in addition to natural climate variability observed over comparable time periods’. The UNFCCC thus makes a distinction between ‘climate change’ attributable to human activities altering the atmospheric composition, and ‘climate variability’ attributable to natural causes. Climate change is a long-term shift in weather conditions measured by changes in temperature, precipitation, wind, snow cover, and other indicators. It can involve both changes in average conditions and changes in variability, including, for example, changes in extreme conditions.

A key difference between climate variability and change is in persistence of ‘anomalous’ conditions. In other words, events that are used to be rare occur more frequently, or vice versa. Occasionally, an event or sequence of events occurs that has never been recorded before, such as the exceptional tsunami in the Indian Ocean in 2004 or hurricane season in the Atlantic in 2005. Yet even that could be a part of natural climate variability. If such a season does not recur within the next 30 years, by looking back it could be called as an exceptional year, but not a ‘climate change’. Only a persistent series of unusual events taken in the context of regional climate parameters can suggest that a potential change in climate has occurred.

Weather and climate have great influence on farm animal production. The environment in which an animal lives is referred to as its habitat. A habitat includes both biotic (living) and abiotic (nonliving) components of the animals’ environment. Abiotic components of an animal’s environment include temperature, humidity, oxygen, wind, soil composition, day length and elevation. Knowledge of how potential environmental stressors (ambient temperature, humidity, thermal radiation, air speed, etc.) can directly and adversely affect animal performance, health and wellbeing is also required for a successful animal farming. The indirect consequences of weather include their impact on feed quality and availability.

Birds and mammals are warmblooded (endotherms or homeotherms), possessing a thermoregulatory system that maintains a stable body temperature and uniform internal environment (homeostasis) by converting food energy into heat. All metabolic processes generate substantial heat and much of this is retained within the body of homeotherms by insulating layers of fat, feathers or fur. Dairy cattle, like other warmblooded animals, function most efficiently in environments where they can maintain their body temperature at around 38° C. Tissue and cellular metabolism and the underlying biochemical reactions that sustain life and productive functions need body temperature to be maintained within very narrow limits. Relatively small increases in body temperature result in the breakdown of body protein and a significant depression in production.

Climate change, particularly global warming has complex impacts on domestic animal production system affecting feed supply, challenging thermoregulatory mechanism resulting thermal stress, emerging new diseases due to change in epidemiology of diseases and causing many other indirect impacts. So, climate change will have farreaching consequences for dairy and meat production, especially in vulnerable parts of the world where it is vital for nutrition and livelihoods. Due to poor availability of good quality feed and fodders in India, animals are generally maintained on poor quality grasses available in the pastures or are stallfed, mainly on crop residues. India is already deficit in feed and fodder. These shortages would be further aggravated by the adverse effects of global warming on fodder crop production.

Many diseases, nematodes, insects and weeds affect crop production, causing severe yield loss. Weather is the most important factor that determines the geographical distribution of these crop pests. The local weather patterns have a significant impact on the abundance of diseases and insect pests in the crops. The severity of disease and pest development depends on the combination of weather conditions during the growing season and is variable from season to season. The weather conditions include temperature (both the maximum and the minimum), light, rain, humidity, dew, cloudiness, sunshine, wind, air currents, evaporation, snow and atmospheric pressure. However, among these weather parameters, temperature and humidity play the major roles in infection of crops due to insect pests and diseases.

Different crops are grown over a wide range of agroecosystems. Though the crops are raised in varied climates, ranging from very hot to very cold, and very wet to very dry, across temperate, tropical and semiarid zones, they are very sensitive to climate. The crop production is dependent on climatic parameters like rainfall, light, temperature, relative humidity and carbon dioxide concentration. Each kind of cultivated crop plants has its own optimum growth requirements. Breeding and selection of new cultivars have allowed for a greater adaptability to less favourable growing conditions than was possible in the past, but the inherent climatic requirements of a specific kind of crop have not changed materially. Crop management is therefore very much about managing climate risk so as to have financially viable and sustainable agricultural systems. Professor Henry Nix of the Australian National University posed three questions that need to be addressed when considering what crop can be grown where (Nix, 1981).

Climate classification systems are ways of classifying the world’s climates. One purpose of climatic classification is to group together places with similar climatic characteristics. That means if an area or region is categorised under a particular climatic type, it possesses broadly uniform characteristics with respect to climate. Classifications have been based on climatic elements such as temperature and precipitation, which are measurable, and on differences in tree species, soil characteristics, topography, etc. The varied nature of earth’s surface and the many interactions that occur among atmospheric processes give every location on the earth a distinctive climate.

Although the delineation of distinct climates may seem likely a very straightforward job, establishing the criteria by which climates are delineated requires considerable subjectivity. There are many ways of classifying the climate depending on the user and the level of understanding of the climate system at a given time. Different regions of the same climate type constitute isoclimatic regions. Identification of isoclimates helps in the transfer of agro-technology and suggesting new cropping pattern. Climatic classification is based on two approaches, viz., generic or empirical approach and genetic approach. In the generic approach the classification is based on the observed climatic elements or their effects on the phenomena, usually vegetation or humankind. The genetic classification is based on climatic controls such as general circulation, net radiation and moisture fluxes.

The concept of climate classification was originally brought out to delineate natural vegetation, which is dependent on rainfall and temperature. Climate classification is unique tool to find out different climate types across the globe, out of which isoclimates or homoclimates can be traced out.

The climate of a particular place is the function of a number of factors such as latitude and its influence on solar radiation received, air mass influences, location of global high and low pressure zones, heat exchange from ocean currents, distribution of mountain barriers, pattern of prevailing winds, distribution of land and sea, and altitude.

Meteorological hazards are severe and extreme weather and climate events that occur in all parts of the world, although some regions are more vulnerable to certain hazards than others. Meteorological hazards include cyclones, droughts, floods, hurricanes, hailstorms, heat waves and tornadoes. The hazard is distinguished from an extreme event and a disaster. An extreme event is simply an unusual event; it does not necessarily cause harm. A disaster is an event that does cause harm in significant amounts. Meteorological hazards are often called as natural hazards. The natural hazards become natural disasters when people’s lives and livelihoods are destroyed.

Hydrological hazards are the result of either excess or a severe lack of water, i.e., flood or drought. Hydrometeorological hazard is a process or phenomenon of atmospheric, hydrological or oceanographic nature that may cause loss of life, injury or other health impacts, property damage, loss of livelihoods and services, social and economic disruption, or environmental damage. Human and material losses caused by natural disasters are a major obstacle to sustainable development. By issuing accurate forecasts and warnings in a form that is readily understood and by educating people about how to prepare against such hazards, before they become disasters, lives and property can be protected.

Evapotranspiration is the combination of two separate processes named evaporation and transpiration. Evaporation accounts for the movement of water to the air from sources such as the waterbodies and soil. Transpiration accounts for the movement of water within a plant and the subsequent loss of water as vapour through stomata in its leaves. So evapotranspiration is a bio-physical process.

Evaporation

The change of state of water from liquid to the vapour and its diffusion into the atmosphere is referred to as evaporation. During evaporation, water molecules absorb energy which gives them the motion required to escape from the surface of liquid and become a gas. Since a certain amount of energy is consumed in the process of evaporation, the remaining liquid is cooled by an equivalent amount. Thus, the process of evaporation is always accompanied by a cooling effect.

As evaporation proceeds, the surrounding air becomes gradually saturated with water vapour and the process will slow down and might stop if the wet air is not transferred to the atmosphere. The replacement of the saturated air with drier air depends greatly on wind speed. Hence, solar radiation, air temperature, air humidity and wind speed are meteorological parameters to be considered when assessing the evaporation process.

In agrometeorology, evaporation is defined as the maximum possible loss of moisture from a wet, horizontal, flat surface exposed to weather parameters, which exist in the vicinity of plants. Evaporation is an essential part of the water cycle. It is the primary pathway through which water moves from the liquid state back into the water cycle as atmospheric water vapour. The oceans, seas, lakes and rivers provide nearly 90 per cent of the moisture in the atmosphere via evaporation, with the remaining 10 per cent being contributed by plant transpiration. A very small amount of water vapour enters the atmosphere through sublimation, the process by which water changes from a solid (ice or snow) state to a gaseous one, bypassing the liquid phase.