eChapters

Abstract

Tripura is expected to be highly prone to the consequences to climate change because of its geo-ecological fragility, strategic location, its trans-boundary river basins and its inherent socio-economic instabilities.  Environmental security and sustainability of the state is and will be greatly challenged by the impacts of climate change in coming years.
Climate and weather can substantially influence the development and distribution of insects.

Sustainable Development A social cause is a problem that influences a considerable number of individuals within a society. There are many environmental issues the India like pollution, waste management sustainable development, rain water harvesting etc.

Evapotranspiration is the combination of two separate processes named evaporation and transpiration. Evaporation accounts for the movement of water to the air from sources such as the waterbodies and soil. Transpiration accounts for the movement of water within a plant and the subsequent loss of water as vapour through stomata in its leaves. So evapotranspiration is a bio-physical process.

Evaporation

The change of state of water from liquid to the vapour and its diffusion into the atmosphere is referred to as evaporation. During evaporation, water molecules absorb energy which gives them the motion required to escape from the surface of liquid and become a gas. Since a certain amount of energy is consumed in the process of evaporation, the remaining liquid is cooled by an equivalent amount. Thus, the process of evaporation is always accompanied by a cooling effect.

As evaporation proceeds, the surrounding air becomes gradually saturated with water vapour and the process will slow down and might stop if the wet air is not transferred to the atmosphere. The replacement of the saturated air with drier air depends greatly on wind speed. Hence, solar radiation, air temperature, air humidity and wind speed are meteorological parameters to be considered when assessing the evaporation process.

In agrometeorology, evaporation is defined as the maximum possible loss of moisture from a wet, horizontal, flat surface exposed to weather parameters, which exist in the vicinity of plants. Evaporation is an essential part of the water cycle. It is the primary pathway through which water moves from the liquid state back into the water cycle as atmospheric water vapour. The oceans, seas, lakes and rivers provide nearly 90 per cent of the moisture in the atmosphere via evaporation, with the remaining 10 per cent being contributed by plant transpiration. A very small amount of water vapour enters the atmosphere through sublimation, the process by which water changes from a solid (ice or snow) state to a gaseous one, bypassing the liquid phase.

15.1 Fuel Cell

Fuel cell is a electrochemical device that convert chemical energy of a reaction directly into electrical energy. The basic physical structure of a fuel cell consists of an electrolyte layer in contact with a porous anode and cathode on either side. A schematic representation of a fuel cell with the reactant or product gases and the ion conduction flow directions through the cell is shown in Fig. 15.1

It is generally observed that N, P and Zn content in soil decreases with increasing soil salinity. Nutrient imbalances created by continuous use of chemical fertilizers, particularly nitrogenous fertilizer alone, combined with sub optimal rates of other nutrients or total omission of other nutrients are the primary causes for unsustainable yields of crops in saline soil. A sustainable approach for nutrient management in salt affected soils should therefore include balanced use of organic, inorganic and biological sources of nutrients (Bandyopadhyay and Rao, 2001). Organic amendments are known to facilitate the reclamation of sodic soils and better nutrition of crops (Anand swarup, 1992).

Coordinate Reference System (CRS) is a framework of coordinate based local, regional or global reference system used to represent the locations of geographic features. Coordinate Reference Systems (CRS) provide a standardized way to define the real-world geographic locations which further enable us to use common locations of geographic datasets for integration. The datasets from different sources and CRS are transformed to a common CRS in order to perform various integrated analytical operations like overlaying of data layers. Coordinate Reference Systems are mainly of two types:

1. Geographic Coordinate System: This is global or spherical coordinate system in which locations of features on earth are defined in terms of latitude and longitude values. Latitude and longitude are angles based on a point at the centre of the earth. In this system, locations are defined by degrees, therefore, distances cannot be measured accurately. The most common geographic coordinate system is the World Geodetic System 84 (WGS84).
2. Projected Coordinate System: In this system, locations of features are defined using cartesian x, y coordinates on a flat, two – dimensional surface. This system is based on sphere or ellipsoid projected on flat surface. Projected Coordinate System are generally referred as projec- tion. It is required for preparing maps on paper or computer screen. Un- like Geographic Coordinate System, projected coordinate system has ac- curate measurements of distance, angles and areas across the two dimen- sions. However, there is alwaystrade-offs between area, direction, shape, and distance in this system due to distortions created while representing ellipsoid or spheroid on a flat map. So, the projection type is selected based on its application. Most common projections are Universal Trans- verse Mercator (UTM), Lambert Conformal Conic and Albers Equal Area.

Abstract

Global warming is predicted to have significant effects in global potato production. Like many crops, potaoes are likely to be affected by changes in atmospheric carbon dioxide, temperature and precipitatiom, as well as interations between these factors. As well as affecting potatoes directly, climate change will also affect the distributions and populations of many potato diseases and pests. Potato is one of the world’s most important food crops. Potato prodcution must be adapted to climate change to aviod reductions in crop yields. Potato plants and potato crop are predicted to benefit from increased carbon dioxide concentrations in the atmosphere. The major benefit of increased atmospheric carbon dioxide for potatoes (and other plants) is an increase in thier photosynthetic rates which can increase their growth rates. Potato crop yields are also predicted to benefit because potates partition more starch to the ediable tubers under elevated carbon dioxides levels. Higher levels of atmospheric carbon dioxide also results in potatoes having to open thier stomata less to take up equal amount of carbon dioxide for photosynthesis, which means loss through transpiration from stomata. As a result the water use efficiency (the amount of carbon assimilated per unit water lost) of potato plants is predicted to increase.

Secondary nutrients

Secondary nutrients includes Calcium, magnesium, and sulfur. Crop plants requires secondary nutrients in moderate quantity for crop growth and yield. Their requirement by plant is less than the macro nutrients. Sulphur and Magnesium requirement of crops are very similar to the Phosphorus needs. Calcium is required in higher amount than Phosphorus. Calcium and magnesium are mostly deficient in acid and alkali soils. In India S deficiencies are found in almost 40 per cent of the cultivated soil. Under intensive cropping system, the use of higher amount of nitrogenous fertilizer without secondary and micro nutrients and lesser use of organic manures are the major reason for the secondary and micro nutrient deficiency in soil.

Weather and climate have great influence on farm animal production. The environment in which an animal lives is referred to as its habitat. A habitat includes both biotic (living) and abiotic (nonliving) components of the animals’ environment. Abiotic components of an animal’s environment include temperature, humidity, oxygen, wind, soil composition, day length and elevation. Knowledge of how potential environmental stressors (ambient temperature, humidity, thermal radiation, air speed, etc.) can directly and adversely affect animal performance, health and wellbeing is also required for a successful animal farming. The indirect consequences of weather include their impact on feed quality and availability.

Birds and mammals are warmblooded (endotherms or homeotherms), possessing a thermoregulatory system that maintains a stable body temperature and uniform internal environment (homeostasis) by converting food energy into heat. All metabolic processes generate substantial heat and much of this is retained within the body of homeotherms by insulating layers of fat, feathers or fur. Dairy cattle, like other warmblooded animals, function most efficiently in environments where they can maintain their body temperature at around 38° C. Tissue and cellular metabolism and the underlying biochemical reactions that sustain life and productive functions need body temperature to be maintained within very narrow limits. Relatively small increases in body temperature result in the breakdown of body protein and a significant depression in production.

Climate change, particularly global warming has complex impacts on domestic animal production system affecting feed supply, challenging thermoregulatory mechanism resulting thermal stress, emerging new diseases due to change in epidemiology of diseases and causing many other indirect impacts. So, climate change will have farreaching consequences for dairy and meat production, especially in vulnerable parts of the world where it is vital for nutrition and livelihoods. Due to poor availability of good quality feed and fodders in India, animals are generally maintained on poor quality grasses available in the pastures or are stallfed, mainly on crop residues. India is already deficit in feed and fodder. These shortages would be further aggravated by the adverse effects of global warming on fodder crop production.

Many times, users have to work with raster datasets of different spatial and radiometric resolutions. So, there is requirement of bringing their resolutions to the same resolution in order to facilitate their processing. Resampling is the process of deriving pixel values from the existing image to the new raster image of different pixel size. Resampling is most common pre-processing step in remote sensing. It is done both at spatial and radiometric scale. At spatial scale, resampling is done either to increase the spatial resolution i.e. decrease pixel size known as Upsampling or to decrease the spatial resolution i.e. increase pixel size known as Downsampling. Radiometric resampling is performed to increase or decrease the radiometric resolution of the image. In R, resampling of raster image is performed by raster package. The details of the resampling methods and their respective R – code with examples are discussed in this chapter.

First of all, we need to import the raster image on which we wish to perform resampling operations by using following R – code. In R, resampling is feasible on one band only. So, we will import single band raster image.

Cation Exchange of Clay Minerals in Soil

The term “clay mineral” refers to phyllosilicate minerals and to minerals which impart plasticity to clay and which harden upon drying or firing. Clay minerals are layer silicates that are formed usually as products of chemical weathering of other silicate minerals at the earth’s surface. Clay minerals in soil play a significant role in exchanging cations, which are positively charged ions, and in regulating soil fertility and nutrient availability. Cation exchange capacity (CEC) is a measure of a soil’s ability to exchange cations and is influenced by the type, abundance, and charge properties of clay minerals in the soil. Clay minerals have a high CEC due to the presence of charged surfaces (silanol and alumoxane groups) that can exchange cations with the soil solution. The most common cations exchanged by clay minerals are hydrogen (H+), calcium (Ca2+), magnesium (Mg2+), potassium (K+), and sodium (Na+). When a soil solution comes into contact with clay minerals, cations in the soil solution are adsorbed or attracted to the charged surfaces of the clay particles.

Abstract

Infertility in Livestock is a matter of great concern Anoestrous and repeat breeding in buffalo and bovines are two of the most serious reproductive problems affecting 30-40% of the total cattles and buffalo population on a conservative estimate our country is loosing 20-30 million tonnes of milk due to anestrus and repeat breading in cattle and buffaloes translating to a loss of Rs 40-50,000 crores annually. The used weak symptoms of estrus in the normal breeding season (September to February) become ever weaker during the hot month of summer. The incidences of silent heat is the lowest in December while the break is seen in the hot summer month of April. Summer infertility is also noticedin goat. During summer farmer experience a variety of reproductive problems such as an estrus extended weaning to eastern interiors, poor conception rates, higher unbryo mortality rates and low barrowing rates. There are strategies to ameliorate heat stress induced fertility problems and gonadotropin treatment can prevent seasonal infertility. There is a need to implement several techniques at the field level combining the glance of any detrimental impact on health and environment

Climate, soil, input and management factors influence the crop yield. Weather is the most important natural input that affects the agricultural production and productivity. The agricultural activities starting from the land preparation to harvest and post-harvest storage are greatly influenced by the weather. The effects of weather on crops may be direct such as those of precipitation, solar radiation, humidity, temperature, etc., or indirect such as those of pest, diseases, weed competition, etc. Thus, the success or failure of a crop is determined by the prevailing weather conditions. Although influence of weather conditions on yield is well established, the quantitative assessment is not always straight forward and simple. The quantitative assessment of the effect of weather on crops is an important application of agrometeorology. The relationship between weather and crop production has been understood through crop weather modelling and study on this aspect through a systematic approach started a century ago. The aim of developing crop weather models is to ensure better utilisation of resources and hence a more environmental friendly and sustainable agriculture.

A model is a schematic representation of the conception of a system or an act of mimicry or a set of equations, which represents the behaviour of a system. Its purpose is usually to aid in explaining, understanding or improving performance of a system. Agricultural models are mathematical equations that represent the reactions occurring within the plant and the interactions between the plant and its environment. However, it is a difficult task to represent any system completely in mathematical terms because of the complexity of the system. Universal models do not exist for the agricultural systems and agricultural models are built for specific purposes and the level of complexity is accordingly adopted. Different models are developed for different subsystems and several models may be built to simulate a particular crop or a particular aspect of the production system. Crop weather models may be defined as a simplified representation of the complex relationships between weather or climate on one hand and crop performance such as growth, yield or yield components, on the other hand by using mathematical and/or statistical techniques

Abstract

Climate change is a change in the distribution of weather over periods of time that range. The effect of climate change is now visible every where including animal farm industry. Projected temperature rise around 2-5oC by 2100 due to climate change is likely estrus, start estrus and decline in reproduction efficiency of livestock species Climate change may have a significant effect on livestock and other animals through is impact on diseases Zoonotic diseases which can be transmitted between vertebrate animals and humans are a matter of great concerns. There is an urgent need for adoption of integrated approaches towards mitigation of advance effects of climate change in animal production. There are nutritional strategies to reduce enteric methane production. Surveillance and monitoring with various adaption strategies are to be brought under purvision to reduce adverse impact of climatic variability in livestock 

Abstract

Aquaculture is facing the serious effects of climate change in the form of scarcity of water and shift in dissolved oxygen level leading to outbreak of diseases. In a study conducted in Farm facilities of ICAR, Tripura it was seen that rise in temperature do have significant effect on hematological and biochemical parameters of fish which are basic index of good health of any organism. Many different diseases occur in the farmers’ pond and which can be controlled. So some basic diseases and their controlling strategies have been pointed out that can lead to better management of fish diseases in pond condition.

Introduction

Manures are obtained from the plant residues, green manure, compost and animal wastes that are used as source of plant nutrients. They release nutrients after their decomposition. They essentially function as sustenance to the crops. They help in the proper cultivation of crops. The addition of manure enables the soil to hold more water. Organic manures have acids that dissolve the nutrients in the soil and make them available to the plants. manures can be grouped into bulky organic manures and concentrated organic manures. Brief dissection about manure given blow flow chart.

Bulky Organic Manure

Bulky organic manures are those materials of plant and animal origin, which contain small percentage of nutrients when added to the soil have tendency to decrease bulk density and to increase soil volume, thus providing better physical conditions for plant growth especially in coarse textured soils and also provide essential nutrients in smaller quantities than the chemical fertilizers. Characteristics of bulky organic manures:

A disaster is sudden event that causes significant damage to the people, environment and the economy. Disasters are serious disruptions to the functioning of a community that exceed its capacity to cope up using its own resources. The disasters that result either due to excess water or severe water deficit are floods and droughts.
12.1. Floods
The flood is an overflowing of water onto land that is normally dry. Floods may occur due to
• Heavy rainfall
• Ocean waves
• Snow melting
The economic losses due to floods will be very high and nearly 68 per cent of the economic losses are attributed to floods only. During the year 2018, India suffered a loss of nearly 90,000 crores due to floods alone. There are several causes for occurrence of floods in India. The major causes are
• Severe cyclonic storms in coastal areas which produce continuous heavy rainfall for 3 to 4 days in succession
• Encroachment of flood plains with residential structures
• Inadequate strength of river banks when there is high flows of water in the rivers
• Unplanned growth of urban areas
• Silting of water storage structures due to increased soil erosion thereby decreasing the storage capacity of reservoirs
• Simultaneous flooding of rivers and tributaries due to excessive water flows

Abstract

Climate change is today’s major concern throughout the world. All sectors have been influenced with the impact of climate change. Similarly, agriculture sector has also been affected with the worse climatic changes. All components of agricultural production system like water, soil, vegetation, organism and microorganism etc. affected greatly due to climatic abruptions. And thus, the productivity is hampering day by day. Today, we requires to predict the trend of changes in climatic parameters like maximum and minimum temperature, humidity, wind speed, sunshine hours etc, to project future change in these climatic parameters, to assess the effect of theses climatic parameters on agricultural components like water resources, soil, vegetation, organism and microorganism and, also to find the adaptation and mitigation strategies.  All these works have beenmainly done by manual methods earlier. Developed country like USA, Japan, UK etc adopted the computer modelling to climate change research. Computer modelling and software assistance have been adopted slowly in developed countries. Since, climatic changes requires processing of very large number of data, they needs computer and software assistance. Without computer assistance climate change research seems to be impossible.

Particle-size distribution is one of the stable soil characteristics, being little modified by agricultural management practices. The particle-size distribution expresses the proportion of various size particles in a soil, especially sand, silt and clay that determine soil texture (Hillel, 2004). Soil texture is closely related to soil physical properties such as water retention and release characteristics, surface area, swelling and shrinking, soil strength and tillage properties. There are two common methods being employed for particle-size (<2.0 mm) analysis namely international pipette method and the hydrometer method. Both the methods are based on Stokes’ law which establishes a relationship between particle size and the rate of sedimentation. Thus, particles are assessed by their settling velocities from suspension in a water solution that can be used to quantify particle size. Size range of soil particles (sand, silt and clay) according to two most adopted systems i.e. U.S. Department of Agriculture (USDA) and International Union of Soil Science (IUSS) formerly known as International Society of Soil Science (ISSS) are given below:

Introduction
Crop production is weather dependent and almost every crop has been affected by the changing climate. The favourable weather may result bumper production sometimes or even complete destruction of crop may take place under severe weather aberrations. The number of events of sudden aberrations is increasing in a cropping period with the gradual climate change in the recent past. It has been recorded too severe in case of perennial crops. Ready to harvest crops have several times been completely destroyed due to thunderstorm or cyclone in coastal regions or even in main land. Thus, Indian agriculture is being impacted by the climatic changes, and its affect is very much visible now (Aggarwal, 2008). Horticulture sector is not escaped from its’ ill affect and new challenges are coming for production (Singh et al., 2021). The role of adaptation strategy has now been felt crucial (Babu et al., 2021; Banerjee et al., 2022) and importance of agro advisory not only protects the crops from such types of risks but also provide guidance to farmers about the right time for activities in crop husbandry (Adak et al., 2018). Issuance for improving water productivity in water limited areas (Adak and Babu, 2024), micronutrient management for nutrient richness and enhanced yield (Adak et al., 2023; Shukla et al., 2020), rejuvenating unproductive orchards (Shukla et al., 2021; Mishra et al., 2007), disease (Misra et al., 2013; Shukla et al., 2015, 2019, 2020, 2021a,b; 2022; Kumari et al., 2021) and insect pest (Gundappa et al., 2016; 2018) management are becoming very crucial and essential for the benefit of growers.