eChapters

Abstract

Water is an essential and vital component for our life support system. Drought and floods are the extreme events of rainfall and the vagaries of monsoon and hydrogeological framework in the country are highly variable from place to place. The water resources available in the country are also not uniformly distributed. The changing Landuse pattern and population growth and the resultant water resources development has lead to water stress at many places. In such areas, the extraction of excessive quantities of groundwater has resulted in the drying up of wells, damages of ecosystems, land subsidence, salt-water intrusion and other related problems. Agricultural, urban & industrial wastes are increasingly threatening the groundwater quality, which is likely to become a more serious issue in the coming years. Considering the seriousness of the groundwater contamination, Central Ground Water Board has carried out detailed studies in few hot spots in the state of Tamil Nadu. The issues related to the water resources contamination and the findings of the studies in parts of Tamil Nadu are summarized in this paper.

ABSTRACT

Over the past four decades groundwater has become a topic of discussion and investigation and as a result the knowledge of understanding groundwater conditions has radically improved. For the past quarter century, remote sensing has played a vital role to target the groundwater resources for the essential survival of horticulture and agriculture crops in drought-prone areas. GIS technology has made a rapid stride for the past one decade to amalgamate the data generated from various space-born platforms and the ground based surveys to facilitate the generation and use of various thematic information for groundwater resources assessment. The present study aims for the demarcation of various groundwater prospective zones in the West Doon Valley and its environs, falling in the SOI toposheet 53 F/15. The role of various parameters namely, Geomorphology, Geology, Lineaments, Drainage, Land Use, Water table and Slope has been integrated for delineating groundwater prospective zones. IRS IC LISS-III geocoded satellite image on 1:50,000 scale was used. Index overlay model has been applied for GIS analysis. The resultant map indicates five prospective zones, such as poor, low, moderate, high and very high groundwater prospective zones in the study area.

ABSTRACT

Identification and mapping of fractures/lineaments and hydrogeomorphic units is prerequisite for undertaking ground water exploration and development in any terrain. Remote sensing and GIS techniques have been used for ground water potential mapping in Theni District. The study area has been divided into various geomorphic units based on visual interpretation of LISS III and PAN merged data in false colour composite on 1:50,000 scale. Ground water potential of each of the geomorphic units was assessed and correlated with geology, structure and recharge factors prevailing in the Theni District.

10.1 Introduction

During rain or heavy irrigation, a part of the rainfall or irrigated water moves below the effective root zone of the crop which moves further below and adds to the water table lying above the impermeable bed or hard rock which is called as  ground  water  reservoir. At  times  the  accumulated  surface  water  is  also recharged to the soil reservoir both naturally as well as artificially that add to the underlying ground water reservoir. This groundwater is an important source of water for irrigation as well as domestic uses. It is the most abundant fresh water resource of the earth. Underground water reservoirs contain large stock of fresh water resources. Total quantity of groundwater within 800 m distance below  the  ground  surface  is  more than  30  times  the  total  water  in  all fresh water lakes, more than 60 times the total water in soil and other unsaturated rock materials, more than 300 times the water vapour in the atmosphere and 3000 times the average volume of all rivers and rivulets in the world (Lenka, 2001). But the distribution of groundwater is not uniform.

Abstract

A pot experiment was conducted to evaluate the genotypic variability with respect to agronomic and physiological traits of Bambara groundnut (Vigna subterranea L. Verdc.) landraces collected from three contrasting environments during 2010-11 in a randomized complete block design with nine replications under transparent shade house at the University of Nottingham Malaysia Campus in Semenyih, Selangor.

Gullies convey runoff and sediment from upstream catchments, but uncontrolled flow enlarges their beds and banks, removes productive land, and may ultimately create ravines. Their development depends on rainfall intensity, runoff volume, catchment size, land use, soil properties, topography, and channel characteristics. Effective treatment requires reducing runoff generation, diverting excess water where appropriate, stabilizing the gully, and restoring vegetation. This chapter presents the principles of gully control and classifies interventions into upstream and downstream measures. It discusses agronomic practices, diversion structures, check dams, drop structures, chute spillways, bank protection, revegetation, and maintenance requirements for safely controlling water velocity, erosion, and sediment transport.

Introduction

Climate change and pollution are the two major concerns that retard growth in animal sector particularly in a developing country like India. Pollution is directly contributed by human beings, while the former is also an after effect of continuous abuse of nature and natural resources. Hence these two areas are to be looked into seriously for country’s growth in general and animal production in particular.

Stress Effect

Stress is nothing but inability of an animal to cope with its environment, a phenomenon that is often ends up with a failure to achieve the full genetic potential. Stress may be from any origin and can even be a disease itself. There exists a variety of endocrine regulatory points of stress which limits the efficiency of production and reproduction. A simple transport produces an immediate constant increase in arginine, vasopressin and corticotrophinreleasing hormone secretion in animals. However, adenocorticotrophic hormone reaches a maximum in the first hour, while cortisol is highest during the second hour. Contrastingly, the hypothalamo–pituitary–adrenal response is delayed occurring only after glucose decreases below a threshold in an insulin treated animal. Negative feedback effects appear to operate mainly at the pituitary level during transport but at the hypothalamus during hypoglycaemia.

Halophytes are salt-resistant or salt-tolerant plants which thrive and complete their life cycles in terrestrial or aquatic habitats having high salt concentrations. Aronson (1989) compiled a partial list of halophytes containing 1560 species in 550 genera and 117 families. Menzel and Lieth (1999) listed as many as 2600 plants under salt tolerant flora. Although halophytes represent only 2% of terrestrial plant species, they are present in about half the higher plant families and represent a wide diversity of plant forms. Because of their diversity, halophytes are regarded as a rich source of potential new crops. Halophytes are tested as vegetables, fodder and oilseed crops under field trials. The oilseed halophyte, Salicornia bigelovii, yields 2 tones/ha of seed containing 28% oil and 31% protein, similar to soybean yield and seed quality.

Introduction

In a technology that consistently maintains a fantastic development curve with capabilities doubling up year-to-year, freezing the hardware specification is not easy or very meaningful. GIS (not geography) owes to its genesis and progress to the developments in information technology front. It may be asserted that any and all upgrade in the hardware industry will only add to its own ability to effectively process more and more data and handle more complex routines. The personal computers of today are seen to be adequate to run typical GIS software. A reference hardware specification is discussed here. GIS software development is an involved process but then the software developers have made good use of hardware capabilities available and have released upgrades consistently. Hardware developments are such that they defy a static spcification. However a reference specification as on 2009. An overview of various software packages used in the past as well as present is attempted. ESRI released a new version in 2002 and claimed that their ArcGIS is an “integrated collection of GIS software products for building a complete GIS that enable users to deploy GIS functionality wherever it is needed, in desktops, servers, or custom applications; over the Web; or in the field.” The details are discussed below. While a number of software overviews are available, this text is not aimed at providing a tutorial to any of the software packages nor do the comparisons made are to promote any particular software. Similarly, it is presumed that the reader is familiar with the hardware elements and functionality. Lot of information about the software packages are available on their respective web sites and the reader is exhorted to look for current, additional and in depth information required in the pages. A brief discussion on Liveware or human resource can be found at the end of the chapter.

Abstract

Agroforestry is an ancient practice that farmers have adopted throughout the world. There are innumerable examples of traditional land use practices combining production of trees and agriculture crops on the same piece of land. In India, the organized agroforestry research began in 1979 when a Seminar on Agroforestry was organized at Imphal by the ICAR, New Delhi. As a follow up to this, ICAR launched an All India Co-ordinated Research Project on Agroforestry (AICRPAF) was started in 1983. The diagnostic survey and appraisal revealed that there are enumerable agroforestry practices prevalent in different agro- ecological zones of India occupying sizeable areas. However, spatial technologies like Geographical Information System (GIS), Remote Sensing (RS) and Geographical Positioning System (GPS) have yet to be implemented extensively in this field in India. The spatial technologies have shown great potential in natural resource management through out the world, especially in developed countries in the fields like forest cover mapping, agricultural planning, watershed management, land use planning, etc. In India the agroforestry land use occupy large areas but use of these technologies to estimate area has been initiated in year 2007 with DST sponsored project entitled ‘Spatial and Temporal analysis of agroforestry interventions in North-western India using GIS and Remote Sensing’ The area under agroforestry systems has been estimated/ mapped in two districts viz., Yamunanagar (Haryana) and Saharanpur (Uttar Pradesh), where intensive commercial agroforestry was predominant. Besides, the methodology developed as an out come of this study may be replicated for agroforestry systems existing in other parts of the country.

Keywords: Agroforestry, Geo-spatial, Mapping, Natural Resources, Remote Sensing.

13.1 Introduction

Winds are the motion of air around the earth. This movement in air is caused by the uneven heating of the planet’s surface by the sun. The idea of using wind as a form of power is not new. The traditional applications of wind were primarily as sources of kinetic energy for rural, agricultural and a limited number of industrial uses such as pumping water and grinding grain.

Presently wind energy can be used for two major applications, such as wind mills for pumping water for drinking as well as for irrigation purposes and second application is as aero-generator for electricity generation for domestic and industrial uses. In addition to this, presently wind energy battery charger are also available, which can store energy for lights, radio communication, hospital equipment and to power various emergency related equipment.

The wind energy has an enormous resource, but the problems of utilizing the winds are many and varied. Wind energy is very diffuse in nature and local topographical features significantly alter the prevailing winds thus leading to the extremely site specific nature of wind energy.

Scientirsts have estimated that as much as 10 per cent of >the world’s electricity could be provided by wind generators by the middle of 21 century. India has estimated wind power potential of 45,000 MW. India now, ranks fourth in the world in wind power generation.

The world’s largest wind farms are in California, where wind turbines can generate power upto about 1120 MW. The first wind mill used as source of electric power was built in Denmark in 1890. Presently in India about 2382 MW of electricity is being produced through wind energy.

Introduction

Harvesting and handling are the equally important activities as the entire production system as an individual activity. Therefore, proper harvesting and handling is essential to assure the farm income. There are various factors which directly affect the storage life of fruits and vegetables as below. The natural limits to the post -harvest life of all types of fresh produce are severely affected by other biological and environmental conditions.

Temperature: An increase in temperature causes an increase in the rate of natural respiration of all produce and food reserves and water content become depleted. The cooling of produce will extend shelf-life by slowing the rate of respiration.

Transpiration and water losses: High temperature, low humidity in the store and injuries to produce can greatly increase the loss of water from stored produce beyond that unavoidable lost from natural causes. Maximum storage life can be achieved by storing only undamaged produce at the lowest temperature tolerable by the crop and at the relative humidity appropriate for the produce.

Mechanical damage: Damage caused during harvesting and subsequent handling (i.e. injuries, impact bruising) increase the rate of deterioration of produce and renders it liable to attacks by decay organisms even under refrigerated storage. Mechanical damage to root crops will cause heavy losses owing to bacterial decay and must be remedied by curing the roots or tubers before storage. Curing is a wound –healing process.

Decay in storage: Decay of fresh produce during storage is mostly caused by the infection of mechanical injuries provoked by micro organisms, mostly bacteria and fungi. Furthermore, many fruits and vegetables are attacked by decay organisms which penetrate through natural openings or even through the intact skin. These infections may be established during the growth of the plant in the field but lie dormant until after harvest, often becoming visible only during storage or ripening.

Standard Operating Protocol for Export of Banana
Banana is one of the important fruit grown in India, as far as its export is concerned it is very limited which is below 1%. For export market it should be harvested at 85% maturity or the bunch is ready to harvest in 80-82 days after shooting initiation. Bunches are to be harvested carefully with two people. One person cut the hand and another person put the bunch onto the padding shoulder. Bunches should be slant cut with sickle shaped sharp knife free from any contamination. For export purpose banana fingers should be square, lie close together, hard, clean and free from any infestation and mucilaginous thread of pulp should be 4-5 cm in length. Skin should not be separated from pulp and no brown spot under the skin. De-handing must be done with sharp chisel type de-handing tool, by leaving maximum crown attached to the hand. The crown should be cut evenly; otherwise its outer finger may be detached. Other way to De-handing by using the nylon thread. It is easy method and it allows maximum crown attach with the land with minimum latex flow. The hands should be carefully paced in clean water which has alum 1 gm litre-1 or sodium hypochlorite (200 ppm) as surfactant for removing the latex and killing the micro-organism after that fruit must be packed in 20-25 kg capacity crates having foam in bottom and in between hands also. The most effective control of post harvest diseases and control of ripening of banana is treating the hands with 1.0% CISH METWASH an organic formulation for 30-60 seconds after that it should be carefully removed from this organic formulation and keep it in front of high speed fan for drying.

Introduction 
Due to the depletion of their raw material supplies, traditional fossil fuel use should be reduced. There is significant hope for biofuel production (Gangl D et al., 2015 ; Seo et al., 2017), and in the past decade, interest in using microalgae has been steadily increasing (Gangl D et al., 2015). The algae group consists of various photosynthetic eukaryotic species that are typically found in both freshwater and marine environments. With an estimated 30,000 to 1 million species, algae range from single-celled cyanobacteria to multicellular forms, each having distinct traits. Microalgae, specifically, grow rapidly and absorb carbon dioxide as they develop (Guiry and M. D., 2012). Many industries have benefited from the utilization of microalgae species for the good of humanity. Food, medications and antibiotics, wastewater treatment, biofuel, biofertilizers, and CO2 fixation are a few of the significant uses for microalgae (Singh et al., 2018 ; Ananthi et al., 2021). Compared to first-generation biofuels, the manufacturing of algae-based biofuel is more advantageous to the environment (Alalwan et al., 2019). Microalgal biofuel production is a greener alternative to first-generation biofuels (Alalwan et al., 2019). It can be cultivated in less ideal locations, such as the ocean or non-arable land, and doesn’t require fertile soil, which helps prevent rivalry with food crops for freshwater and farmland (Winckelmann et al., 2015; Correa et al., 2020). Microalgal production systems can help treat wastewater or convert CO2 into oxygen without interfering with the food supply (Onyeaka et al., 2021; Prasad et al., 2021). Nanotechnology and nanomaterials are becoming increasingly popular across many fields for their useful properties, with global research exploring their role in biodiesel production and processing. To speed up the development of biodiesel production, advanced nanotechnology is being emphasized to achieve higher yields at lower costs. Microalgae are a promising source for biodiesel production, and various nanoparticles can significantly boost the efficiency of harvesting them. Reusing nanomaterials and combining cell harvesting, disruption, and extraction processes also help reduce costs. Moreover, different nanocatalysts can enhance the efficiency of biodiesel conversion (Verma and Kuila, 2020). Currently available techniques for microalgal harvesting include chemical, mechanical, biological, and electrical ones to some extent. Harvesting microalgal biomass is most often done by mechanical means since they are the most dependable (Grima et al., 2003 ; Christenson et al., 2011). But, in order to increase productivity and reduce operating and maintenance expenses, these procedures are frequently followed by biological or chemical flocculation phases. For maximum separation efficiency and minimum cost, two or more of these techniques are frequently used. For instance, processing costs can be significantly decreased by combining centrifugation and flocculation-sedimentation (Schlesinger et al., 2012). Novel approaches like biological treatments have the potential to further lower operating expenses.

Introduction

Stress represents the reaction of body to stimuli that disturb normal physiological equilibrium or homeostasis, often with detrimental effects (Khansari et al., 1990). Domestic animals undergo various kinds of stress such as physical, nutritional, chemical, psychological and thermal stress (Marai et al., 2007; Nardone et al., 2010). Figure 1 summarises the different types of stressors and their effects on animals.

Whenever the daily maximum temperature exceeds more than average values during summer season the heat wave will occur. Similarly, whenever the daily minimum temperature falls below the average values cold wave will occur. The India Meteorological department has developed the criteria to identify the occurrence the heat waves and cold waves.

11.1 Heat Waves

Heat wave is defined as the condition when the daily maximum temperature is 45ºC or more. Based on departure from normal daily maximum temperature of 40ºC onwards the heat waves are defined as follows:

ABSTRACT

Using a hand auger of 2 m length, upper, middle and lower core sediment samples of seventy nine in number have been collected from the Vaippar river, its tributaries and Vaippar beach in order to understand the role of Vaippar river and its tributaries in making up the Vaippar beach placer deposits. The heavies are found to be concentrated abundantly in fine and very fine size grades of all the samples collected from both the environments. The average heavy mineral concentration varies from 3.13 to 17.40 % in river bed while it is 6.19 – 64.82 % in the beach. In river bed, the pattern of concentration of heavies in upper, middle and lower core samples does not show any characteristic uniform pattern and inferred that it is controlled by the grain size of the parent rock, supply of sediments from the source, geomorphological features of the river and hydrological characters of running water. In the beach, the concentration of heavies are effected mainly due to the winnowing action of waves. However, a phenomenal increase in the heavy mineral concentration of beach samples might be due to the supply of sediments from other source besides the Vaippar river.

Introduction

Arid and semi arid parts of the India are known as Seed Spices Bowl (Rajasthan and Gujarat) and contribute more than 80% of total seed spices production. Total 109 spices are listed by ISO and 63 spices are grown in India and out of which 20 are being classified as seed spices. Out of 20 seed spices, ICAR-NRCSS working on 10 most important seed spices namely cumin, coriander, fennel, fenugreek, ajwain, anise, caraway, celery, dill and nigella (NRCSS Vision, 2050). Seed spices also grown in some other states on considerable areas such as Uttar Pradesh, Madhya Pradesh, Bihar, West Bengal, Orissa, Punjab, Karnataka and Tamil Nadu. Since there is a large scope of seed spices by introducing them in new areas, the higher yields can also be achieved effortlessly by implementing new technologies. Among seed spices, maximum area is under cumin followed by coriander, fennel fenugreek, ajwain, celery, nigella, dill, anise etc. Being seasonal crops, these are grown extensively in rotation with food crops and also as inter/mixed crops under rainfed/irrigated conditions. All these crops mostly grown in rabi season. India is the largest producer, consumer and exporter of seed spices in the world. Out of total area and production in spices, seed spices contribute about 51.79% of total area and 19.06% of production of spices in the country. The area under seed spices is about 1.74 million hectare and 1.45 million tonnes. India is consistent source of seed spices for importing countries worldwide. There has been ever increasing demand of seed spices and importing countries look at India for quality produce of seed spices.

8.1. Biofloc aquaculture

Among the innovations in the field of aquaculture, biofloc technology (BFT) has attracted great attention due to its ability to foster the goals of sustainable aquaculture (Khanjani et al., 2022a). If implemented correctly, BFT capitalizes on the existing organisms in water to significantly reduce water use and environmental impact and increase biosafety at farms (Avnimelech, 2012).