eChapters

Aim

Studies on plane table survey instruments

To determine the area of given open field by radiation method of plane table survey.

Plane table survey

Plane table surveying is a simple method of surveying for determination of area of field. The plane table survey is quite suitable for plotting small-scale and medium scale mappings directly in the field where great accuracy is not required. It is also used for plotting the topographical maps in the field. The plane table survey is generally more rapid and less costly than other types of survey.

In this survey, a plane table is used for taking the measurements and for plotting the plan in the field. Plane table surveying is a method in which the field observations and plotting of the plan proceed simultaneously. The plotted map can be compared with the actual features in the field. Errors in measurements and plotting can be easily detected in the field by taking suitable check lines.

Aim

To determine the area of given field by intersection method of plane table survey.

Materials required

Tripod

Plane table

Plumbing fork

Level tube

Magnetic compass

Alidade

Measuring tape

Ranging rods

Drawing sheet

Pins, pencil and eraser

Aim

To determine the area of given field by triangulation method of chain survey

Materials required

Metric chain

Measuring tape

Ranging rods

Chain pins

Aim

To find out the area of given field by cross-staff survey method

Materials required

Cross-staff

Metric chain

Measuring tape

Ranging rods

Chain pins

Aim

To determine the area of the given field by radiation method using a prismatic compass.

Materials required

Prismatic Compass

Tripod

Measuring tape

Arrows

Ranging Rods

Theory

Bulk density of the food material play an important role in many applications such as drying, storing, separation of undesirable material, determining the purity of seeds, grinding, maturity evaluations, design of storage structures, etc. It is an important parameter in packaging requirement and is often 2-20% of true density. Bulk density is the density of material when stacked or packed in bulk. Bulk density of powder can be determined under loose conditions. Loose packing is defined as the state obtained by pouring a powder sample into a vessel without any consolidation.

Bulk density

Bulk density of the food material can be defined as the ratio of weight of an untapped material to its volume including the contribution of the inter-particulate void volume. There are two kinds of voids, voids between particles and void within particles. Weight of the material can be determined by weighing balance. Volume can be determined by measured dimensions or using liquid or gas or solid displacement methods.

Aim

To determine the contours by cross-section method using dumpy level.

Materials required

Dumpy level

Leveling staff

Measuring tape

Wooden pegs/chain pins

Field book

Aim

To determine the contours by grid method using dumpy level.

Materials required

Dumpy level

Leveling staff

Measuring tape

Wooden pegs/chain pins

Field book

Aim

To determine the contours by radial line method using dumpy level.

Materials required

Dumpy level
Leveling staff
Measuring tape
Wooden pegs/chain pins
Field book

Description

Bucket elevator is one of the equipments used in the material handling to convey the material vertically. The lab model bucket elevator (Fig.34.1) consists of number of buckets/cups arranged to an endless flat belt. The belt with cups run vertically and cups are placed at a particular interval in the belt. The belt is wrapped over two pulleys, one at the top is called head pulley which receives power from an electrical motor 0.5 hp through suitable power concentration and rotates at required rpm. The belts, cups and pulleys are mounted on a steel frame. The grain from the hopper is reaches to the bottom pulley. The bucket is filled with grains during upward movement and is discharged at the top due to the centrifugal force. An outlet is provided at the top to collect the discharge grain. The capacity depends on the bucket size and seed of operation. For proper discharge of the material, the weight of the material in each cup should be equal to the centrifugal force created due to rotation.

Description

Screw conveyor is one of the equipment used in material handling to convey the material horizontally. The screw conveyor consists of screw blade, screw shaft, coupling, tubular trough, cover, inlet and outlet gates, bearings and drive mechanism. A shaft with spiral screw revolves in the tubular trough. The screw shaft is supported by end and hanger bearings. The rotation of screw pushes the grain along the trough. The pitch of a stranded screw which is the distance from the center of one thread to the center of the next thread is equal to its diameter

Aim

To study the determination of drying rate of agricultural products

Problem

In a drying experiment on paddy at an air temperature of 60ºC, the following data were obtained. Prepare a drying rate curve for the experiment. Initial weight of the sample is 1250 gm and initial moisture content is 35% (d.b).

Theory

This type of moisture measurement is called brown-duvel fractional distillation method. The method is recognized as an official method for determination of moisture content. In this method, directly measures the volume of moisture in cubic centimeter. This apparatus consists of flask, burner, thermometer, condenser, graduated cylinder. This apparatus consists of flask in which grain sample is boiled with mineral oil.

Theory

Indirect methods are based on the measurement of electrical properties of the grain that depends upon moisture content. There are two indirect methods namely (i) electrical resistance and (ii) dielectric methods are used. The electrical conductivity or resistance of a product measures its moisture content at a given compaction and temperature. The electrical resistance is depends on its moisture content, degree of compaction, grain temperature and impurities present in the sample. The universal digital moisture meter measures the electrical resistance of the grain at a given compaction. Universal moisture meter gives fairly accurate readings of moisture content on wet basis. In dielectric method, grain moisture content can be measured with the help of dielectric properties of the grains.

Theory

The amount of moisture in a product is given on the basis of the weight of water present in the product and is usually expressed in percent. Moisture content is designated by (i) wet basis (wb) and (ii) Dry basis (db). The moisture content on dry basis is more simple to use in calculation as the quantity of moisture present at any time is directly proportional to the moisture content on dry basis.

Theory

Porosity is a physical property characterizing the texture and the quality of dry and intermediate moisture foods. Porosity means inter-granular space. It is the measure of void space between the materials. Porosity may be defined as the percentage of volume of inter-grain space to the total volume of grain bulk. Porosity depends on size, shape, dimension, and roughness of grain surface.

The porosity of an unconsolidated agricultural material can either be determined experimentally using the porosity tank method or theoretically from bulk and true densities of the material. Porosity can be determined from the difference between bulk volume of a porous material and its volume after destruction of all voids by compression. Porosity determination requires the knowledge of the total or apparent volume, and the void volume included in the material matrix; their difference is also known as the particle volume.

Determination of size of the food materials

Size is an important physical attribute of foods used in screening solids to separate foreign materials, grading of fruits and vegetables, and evaluating the quality of food materials. Various types of cleaning, grading and separation equipment are designed on the basis of size. The size and shape of the grains are used to determine the size of screen openings, angle of inclination, vibration amplitude and frequency of screen in designing an air screen grain cleaner and conveying characteristics of the solid materials.

Theory

The specific gravity is defined as the unit weight of the product mass divided by the unit weight of distilled water at 4°C. The unit density is obtained by measuring the volume and weight of a unit product. Sometimes it is required to compare the density of the product to the density of water. This comparison is in the form of ratio and is termed as the specific gravity.

Specific gravity also known as relative density is the ratio of density of a substance to the density of a standard substance at the same temperature and pressure. For solids and liquids the standard substance is water while for gasses it is air. The specific gravity of food material play an important role in design of storage bins, conveying equipments, separation equipments, etc. The specific gravity is frequently used to solve the various phase relationships, including void ratio, porosity and degree of saturation together with the moisture content and unit weight. It is also used in calculations associated with the grain size analysis, consolidation and compaction. Pycnometer method, which is a standardized vessel for determining specific gravity. It involves a standard container of accurately defined volume used to determine the specific gravity of solids and liquids.

Theory

Specific heat is defined as the amount of heat needed to raise the temperature of one kg of the material by one degree at constant pressure without a change in state. With food materials, specific heat is a function of different components of a food, moisture content, temperature, and pressure. Specific heat is an important parameter in thermal analysis of food processing and equipment used in heating or cooling of foods. The numerical values of specific heat of the food materials are used in designing food processes and processing equipment. It can be used to calculate the heat load imposed on the refrigeration equipment by the freezing of foods. An apparent specific heat is used in freezing or thawing and in most food processing applications.

The specific heat of a food increases as the product moisture content increases. In unfrozen foods, specific heat capacity is relatively constant with respect to temperature. However, for frozen foods, there is a large decrease in specific heat capacity as the temperature decreases. The specific heat of a material can be determined experimentally by static (adiabatic) calorimetry or differential scanning calorimetry. It can be also predicted quite accurately with the help of a number of empirical equations. The equations are empirical expressions, obtained by fitting experimental data into mathematical models. The mathematical models are based on one or more constituents of the food. Since water is a major component of many foods, a number of models are expressed as a function of water content.

Aim

To determine the tapped bulk density and flowability of the food powder.

Materials required

Raw material (powder)

Measuring cylinder

Electronic weighing balance

Tapped bulk density of the powder

Tapped bulk density is measured for powdery samples. The volume is measured after tapping the powdery material so that the product is adjusted to inter-granular spaces, but it cannot eliminate all the inter-granular spaces. The tapped density is an increased bulk density attained after mechanically tapping a container containing the powder sample.