eChapters

Millets are essential grains that help developing nations in Asia and Africa’s semi-arid tropics, particularly India, Nigeria, and Niger, achieve food and nutrition security.They are grown on soils that are usually too weak for any other crop to grow. They can withstand drought, minimal fertiliser treatment, and temperature swings better than other cereal crops, and their short growing season makes them exceptional. Millets are all-season crops that can be grown all year and provide several security benefits (food, feed, health, nutrition, livelihood, and the environment), making them the most cost-effective agricultural security crop. Sorghum (Great millet), Bajra (Pearl millet), small millets such as Korra (Foxtail millet), Ragi (Finger millet), Kodo millet, Proso millet, Little millet and Barnyard millet are all important millet crops grown in India.

Nutraceutical is a broad term which represents any substance extracted from food sources with additional health benefits alongside the good nutritional value already present in them. The nutraceutical term was originated by Stephen De Felice in 1989.

The stiffness of starch gels from different starches at 5% concentration was shown in decreasing order of stiffness in the following table. Of the cereal starches corn starch gel was firmest followed by wheat and rice starch gels. Among the roots and tubers starches, potato yielded a ropy paste, arrowroot a soft paste while cassava starch gave viscous fluid.

In order to assess the quality characteristics of eggs the book reference values were taken for comparison

Pure sugar when heated melts at about 160-1800c. at about 2100c sucrose loses water and becomes caramel.

Pickling is the process of preserving or extending the shelf life of food by either anaerobic fermentation in brine or immersion in vinegar. The pickling procedure typically affects the food’s texture and flavor. The resulting food is called a pickle, or, to prevent ambiguity, prefaced with pickled. Foods that are pickled include vegetables, fruits, meats, fish, dairy and eggs.

Yogurt is a fermented milk product that contains the characteristic bacterial cultures such as Lactobacillus bulgaricus and Streptococcus thermophilus. All yogurts must contain at least 8.25% solids not fat.

Sample Preparation

Sample should be taken at six or more points on the top of the surface by means of a tubular trier of sufficient length to extend to the bottom of the barrel. Remove this cores and transfer to clean, dry, air tight container and seal immediately.

Before opening sample for analysis, make homogenous either by shaking or by alternately rolling and inverting container. If lump are present, sift sample through No 20 sieve, rubbing material through sieve and tapping vigorously, if necessary.

Avoid sampling on rainy day or when humidity is high, so as to reduce moisture absorption from air.

1 Determination of Moisture Content by Moisture Balance Introduction

In this procedure, infra-red radiation is used to accomplish rapid drying. The tester has a sensitive torsion balance which permits rapid determination directly from the balance scale, eliminating the need for computing or calculation to obtain results. This method is useful for the in-process determination of moisture because the results may be obtained in minutes.

Ice Bank Cooler: Air forced cooler leads to desiccation of the produce. So use forced air high humidity cooler and these are known as Ice Bank Cooler. Ice bank Coolers are useful for strawberry.

Ice bank cooling: Storing of fruit and vegetable in storage chamber with positive ventilation and system countries where ice formation is allowed during night time (as electricity cost of night is less as compared to the day time). Melting of ice occurs during day time and with proper air circulation by means of ventilation process, approximately 0.5-10C temperature with 90% RH in the chamber is maintained. Ice Bank Cooler / Air forced cooler leads to desiccation of the produce (Plate 205). So use forced air high humidity cooler and these are known as Ice Bank Cooler. Ice bank coolers are useful for strawberry.

Ice cream cone: A thin crisp edible cone for holding ice cream and filled with ice cream.

Ice cream: Ice cream may be define as frozen dairy product made by suitable blending and processing of cream and other milk products together with sugar and flavour.

Ice point: It is the temperature of equilibrium between ice and water under normal atmospheric pressure (0oC).

Ichthylogy: It is the branch of the zoology that deals with the study of fishes (Pisces).

Vacreation: The pasteurization of the milk or cream under reduced pressure by direct steam is called vacreation.

Vacuum: The state of negative pressure.It is equal to atmospheric pressure minus absolute pressure.

Vacuum cooling: A technique of cooling vegetable (leafy vegetables, asparagus Brussels sprouts) having a high surface to volume ratio rapidly and uniformly by boiling off some of their water at 10C and at low pressure (5 mm of Hg) into a sealed container. The produce is cooled by evaporation of water from the tissue surface and is more rapid than hydro cooling.

Vacuum drier: A drier used to dry heat sensitive products where low pressure lowers the temperature, helps to retain natural flavour and minimizes oxidation and browning is called vacuum drier (Plate 325).

Vacuum gauge: A gauge indicating degree of rarefaction (state or region of minimum pressure in a medium) below atmospheric pressure.

Vacuum packed: A packhaving much of the air removed before being hermetically sealed is called vacuum pack (Plate 326).

Introduction

To accomplish experimentations in laboratories, sometimes we need microscope to test/validate our ideas/findings. A microscope is needed to examine objects which are very small which cannot be visualised by naked eyes. However, microscopic study requires some expertise in operating the microscope, particularly the sophisticated microscopes, as well as to prepare (peeling, sections, cutting, fixation, staining, dehydration, mounting, etc.) the sample, so that it can be appropriately examined for the anticipated details.

According to the scientific requirements different types of microscopes are used in the laboratories for research purpose. In this chapter, our aim is to acquaint you with the basics of using and handling of microscopes, particularly a compound microscope that is commonly used by the graduate and post graduate students for basic research.

Microscopy is often designated as the scientific investigation that is employed to review and analyse minute structures and objects using a microscope. The term “microscope” has been derived from ancient Greek words “micros” meaning “small” and “skopeîn” meaning “to look at or see,”.

Microscope

A microscope is a laboratory instrument used to examine objects (biological specimens) which are too small to be seen by the naked eye. The microscope must accomplish three tasks:

• Magnification- to provide a magnified image of the specimen.

• Resolution- to separate the details in the image.

• Contrast- to render the details clearly visible to the eyes.

Although we will tnroduce to you the different types of microscopes used for different speciments, our main focus is to discuss about compound microscope, which is commonly used in the laboratories. Compound microscope was developed around the beginning of 17th century.

Introduction

Test of pollen viability (extent of pollen viability) is important in pollination experiments to ensure fertility/seed setting. It is also important in monitoring state of pollens during storage in ecological/ taxonomic studies as well as during research on pollen biochemistry, genetics, stigma interactions, and incompatibility studies. Pollen viability refers to the ability of pollen to accomplish post-pollination events to achieve fertilization. Pollen viability test has gained importance particularly in plant breeding and hybrid seed production experiments/ practices. In this chapter, you will be acquainted with the basics of pollen viability test. However, for more professional knowledge on the topic readers are suggested to refer specialized books.

Pollen Viability Test

It is important to know the extent of viability of pollens used in pollination experiment, in finding fertility of a plant of interest, to monitor state of pollen on storage, in ecological/taxonomic studies, as well as in research on biochemistry, genetics, stigma interaction, incompatibility assay, etc. of pollen. Several pollen viability tests have been developed time-to-time. It is recommended to initially use different tests for a given pollen type to find out the most appropriate method that provides reliable result on pollen viability. It is important to note that every procedure requires standardization of protocol according to the sample used. Following different tests are used for assessing pollen viability.

1. In-vitro Pollen Germination Test

It is a simple, speedy, and quantitative test for assessing pollen viability. In this method, a collection/sample of pollen is germinated in vitro and observed under microscope. The percentage of germinating pollens (producing pollen tube) after appropriate treatment and a given period of time is determined. The percentage provides an index of viability of the pollen sample.

Diversity of gut microbial community

The human microbiota (the collection of microbes that live on and inside us) consists of about 100 trillion microbial cells that outnumber our ‘‘human’’ cells 10 to 1, and that provide a wide range of metabolic functions that we lack. It has been estimated that they encode 100-fold more unique genes than our own genome. Furthermore, the gut microbes contribute to energy harvest from food, and changes of gut microbiome may be associated with bowel diseases or obesity. To understand and exploit the impact of the gut microbes on human health and well-being it is necessary to decipher the content, diversity and functioning of the microbial gut community. If we consider ourselves as superior organisms encompassing these microbial symbionts, by far the majority of genes in the system are microbial. In this sense, completing the human genome also requires the characterization of the microbiome (the collection of genes in the microbiota).

Methods of counting viable and non-viable bacteria in gut

Before the advent of genome sequencing and genome-wide analysis method, our knowledge of molecular characteristics of diverse gut microbial population was extremely limited. To obtain an estimate of cultivability, microbial ecologists generally compare microscopic counts with total viable counts. The total viable count made on a nonselective agar based medium estimates the number of colony forming units (cfu) per gram of sample. The finding that total viable counts are typically lower than total microscopic counts was thought to be due to the number of dead cells. Indeed, dead bacteria in feces may constitute up to one third of the total bacterial community. However, recent nucleic acid based studies indicated that a majority of bacteria in a variety of ecosystems are different from those described in culture.

Cheese is made from milk, with the addition of cream, buttermilk, and/or whey. This basic raw material is also called cheese milk. Cheese consists mainly of casein (the major protein of milk), other milk proteins, fat, other milk components, and a certain percentage of water, which is bound. Proteins are precipitated by enzymes and/or acidification as well as heat and are separated by suitable processes from the aqueous phase. (whey, serum). Cheese is most often molded, pressed, and salted and has fungal and bacterial culture additions. colorants, herbs, spices, and other non-dairy ingredients are also added to the cheese. It is consumed either fresh or at different stages of ripening.

Worldwide, there are more than 2000 types of cheese, sometimes made by very different manufacturing processes. A classification can be based on several aspects and is done in different countries according to different criteria. A general classification can be made for three major groups:

a. Rennet or natural cheese: manufactured straight from milk by using proteolytic enzymes (rennet) and acid, with a more or less pronounced ripening process.

b. Fresh cheese or non-ripened Cheese: Quarg, fresh cheese, and white cheese are examples. Its manufacturing process is similar to that of rennet cheese manufacturing, but it has a high degree of acidity and is not subjected to a proteolytic ripening process.

c. Long-life cheese (processed cheese): it is more often made from rennet cheese and is textured by thermal treatment and made shelf-stable.

Introduction

Entrepreneurship has become a major driver of economic development in recent years. It involves starting new businesses or revitalizing existing ones, often through recognizing and seizing new opportunities. Entrepreneurs are individuals who organize, manage, and take on the risks of a business venture with the aim of making a profit. They identify market opportunities and introduce new technologies and organizational improvements. Entrepreneurs constantly innovate and create value from these opportunities. According to Hisrich (1990), entrepreneurs are proactive and creative individuals who can organize resources and manage risks and failures to succeed.

To grow as an entrepreneur, it is essential to develop and refine key entrepreneurial traits. These traits shape an entrepreneur’s skills and abilities, aligning with their motivations and guiding them to drive their business forward. Entrepreneurial characteristics are a mix of personal, social, and environmental factors that influence a business ecosystem. These traits play a key role in shaping a company’s goals and strategies, ultimately affecting its performance.

Introduction

A collaborative environment is necessary to enable a nurturing future for any business or entrepreneurship to succeed. While ventures may or may not have benefitted from collaborations, it is undoubtedly a step highly considered and regarded in any kind of field be it research, business, partnership between organizations or any international collaborations. The parties involved in these collaborations/partnerships share resources and risks as per agreed. The various kinds of models are discussed in this chapter ahead.

Venture Capital

Venture capital refers to financing that comes from companies or individuals in the business of investing in young, privately held businesses. They provide capital to young businesses in exchange for an ownership share of the business. Venture capital firms usually don’t want to participate in the initial financing of a business unless the company has management with a proven track record. Generally, they prefer to invest in companies that have received significant equity investments from the founders and are already profitable. Venture capital investors also prefer businesses that have a competitive advantage or a strong value proposition in the form of a patent, a proven demand for the product, or a very special (and protectable) idea. Startups with innovative ideas and technologies that have a great potential for wealth creation, but a high risk of failure might receive funding from venture capital. Typically, venture financing comes in the form of equity shares or a claim on equity that may arise in the future, such convertible debt, allowing the venture capital firm to acquire a portion of the company. New businesses are often the focus of venture capital, and Georges Doriot, a professor at Harvard Business School, is widely regarded as the “Father of Venture Capital.”

Introduction

A marketing plan is a strategic document that guides an organization in generating leads and engaging with target customers. It serves as a roadmap for how a company will approach the market, akin to a job description for the business. Every organization needs a well-crafted marketing plan that is tailored to its specific objectives, regularly updated, and aligned with customer demands. Companies with a solid marketing plan tend to be more successful and outperform their competitors compared to those without one.

The marketing plan outlines a strategy for growth by detailing how a company will attract and retain customers. It is an integral part of the overall business plan and lays the foundation for future market opportunities. A strong marketing plan focuses on customer needs and provides a clear roadmap for launching new products, expanding the customer base, and boosting the company’s profile. It includes essential elements such as business goals, mission, budget, and strategies. A well-designed marketing plan ensures effective promotion of products and services, helping businesses reach their target market and track success. Moreover, it should be flexible and adaptable to the evolving market landscape.

Introduction

India has cemented its position as the global leader in milk production for 2023-24, contributing a staggering 230.58 million tonnes, or 25% of the world’s total supply. This achievement reflects an annual growth rate of 4%, driven by a vast network of small-scale farmers who manage one or two milch animals each. Despite their limited productivity, these farmers collectively power the nation’s dairy industry. Before the transformative Operation Flood, the sector was fragmented, dominated by middlemen, and poorly linked to urban demand. The initiative revolutionized the industry, introducing cooperative, private, and state driven organizations that established a seamless system for milk procurement, processing, and marketing. Today, thousands of dairy factories across the country transform raw milk into value-added products to meet India’s immense demand, with rural households allocating 15.51% of their food budget to dairy and urban households spending an even higher 18.19%. Coordinating milk collection from millions of scattered producers and delivering it to processing facilities is a monumental task, yet this streamlined system ensures that India’s dairy sector continues to thrive and satisfy its growing consumer base. India’s dairy export performance in 2023-24 was nothing short of “legendairy,” shipping 63,738.47 metric tonnes of dairy delights worth $272.64 million to fans in the UAE, Saudi Arabia, USA, Singapore, and Bhutan. Butter, ghee, and dairy spreads took the spotlight with $43.65 million in exports (8,106.54 MT) to destinations like Saudi Arabia, Bahrain, and Qatar, spreading Indian flavor worldwide. Cheese exports were equally impressive, with 9,262.63 MT worth $46.84 million making their way to the UAE, USA, and Bhutan clearly, everyone loves a slice of India.

Introduction

Though India is a highest producer of milk in the world, only 15 to 20 per cent of the milk is marketed through organized sector comprised of cooperative societies, public and private processing plants. Bulk marketing is limited to processing plants and cooperative societies. In contrast to Indian situation, most of the milk in developed world is consumed in different processed forms. It is something very general to India where overall food markets for processed foods are generally low and same is the case with milk. By all estimates about 75 per cent of the milk purchased by the consumer as liquid milk whether raw or processed. The share of pasteurized milk is only 10 per cent but the demand is increasing at the rate of 15 percent per annum. One fourth of the milk production is processed in the unorganized sector transforming into products like, sweets. Khoa, paneer, curd, lassi, etc. There are small scale milk product manufacturing units which fall in the category of semi-organized sector comprised of creameries, ice-cream units which are manufacturing the similar products as produced by the composite milk plants in the organized sector. They generally serve the local markets but have the important share in processing of milk as well as meeting the consumers specific demands. The organized sector comprised of mainly dairy plants, procures surplus milk through Milk Producers Cooperative Societies and generally follows the HACCP standards leading to quality of the products, whereas unorganized sector is composed of milk vendors, contractors, halwaies and creameries, collect milk from producers and sell either as raw milk or manufactured milk products or both.

Introduction

India’s rural economy has benefited greatly from the dairy sector. It has played a significant role in bringing about socioeconomic change. India’s dairy industry has undergone significant change as a result of the White Revolution. The “White Revolution” can be credited with increasing milk availability and providing rural India with a stable source of employment and income. The business has drastically changed to meet India’s increasing demand for milk and milk products. India is currently the world’s greatest producer of milk. The Operation Flood Program is credited with this title. The dairy market in India is projected to increase at a compound annual growth rate (CAGR) of 6.61% from 2024 to 2029, from an estimated US$26.11 billion in 2024 to US$35.96 billion by 2029 (Indus Food, 2024). With over 8 crore farmers employed and a 5% national GDP contribution, the dairy industry in India is vital to the country’s economy. With around 25% of the world’s milk supply and a massive livestock population of 536.76 million animals, it tops the world in milk production. With major markets in the United Arab Emirates, Saudi Arabia, the United States, Singapore, and Bhutan, India exports approximately 63,738.47 metric tonnes of dairy products in 2023–2024, generating US$ 272.64 million.

Introduction

Government initiatives aimed at supporting small-scale enterprises and fostering women’s entrepreneurship are crucial for driving economic development, job creation, and social empowerment. Small-scale enterprises, including micro, small, and medium enterprises (MSMEs), play a vital role in the economy by contributing to employment, innovation, and poverty reduction. Similarly, women entrepreneurship offers significant potential for promoting inclusive growth, tapping into underutilized talent, and advancing gender equality in business leadership.

Small-scale enterprises often face challenges like limited access to funding, poor infrastructure, regulatory barriers, and market limitations. Women entrepreneurs, on the other hand, encounter additional obstacles such as socio cultural norms, limited access to resources, and gender biases in the business world. To address these issues, governments globally have introduced policies and initiatives aimed at supporting small enterprises and encouraging women’s participation in entrepreneurship.

The distribution systems are designed to ensure that processed fluid milk is stored and transported under optimal conditions, maintaining its quality and freshness until it reaches consumers. An effective distribution system for processed fluid milk involves careful planning and execution to guarantee timely delivery, quality preservation, and customer satisfaction. Given that milk is a highly perishable product, it requires meticulous handling and strict temperature control. Technology plays a crucial role in preserving its integrity throughout the supply chain. The use of technology reduces human error, increase the efficiency of distribution operations, and lower operational costs by preventing idle resources through coordinated logistics for both outbound and inbound trips.
To address the specific demands of manufacturing, packaging, distribution, and transportation, integrated business process automation solutions are implemented. These solutions include following features:
• Identify and define the most efficient delivery routes, reducing transportation costs and ensuring timely delivery.
• Scheduling and monitoring of delivery routes to maintain optimal delivery speeds, and manage loading and unloading processes so as to minimize exposure to adverse conditions. Automated solutions and tools help maintain the required temperature conditions throughout the entire supply chain.
• Verify and document supplier practices to ensure that all partners in the supply chain adhere to the agreed-upon temperature standards. Store the temperature-related data to help in auditing and analysis, and continuous improvement of the cold chain process.
• Shelf life and expiration date management is a critical component in  the storage and transport of dairy products. Proper management ensures that dairy products remain safe for consumption and retain their quality throughout the distribution chain.

18.1 Introduction
Ice cream is produced by freezing a pasteurised mixture that is derived from milk or milk products, with or without nutritive sweeteners and other approved non-dairy constituents, in accordance with FSSAI standards. Except for softserve ice cream, which may remain malleable, this product must freeze solid and may contain air. Ice cream is manufactured using bovine or buffalo milk, cream, or milk products. It may also contain cane sugar, eggs, fruits, fruit juices, preserved fruits, nuts, chocolate, edible flavours, and approved colours. Up to 0.5% by weight of stabilisers and emulsifiers are permissible. The mélange must be heated to the appropriate temperature prior to freezing. A minimum of 10% milk fat, 3.5% protein, and 36% total solids must be present in the product. However, the proportion of milk fat may be reduced to no less than 8% by weight when any of the aforementioned preparations contains fruits, almonds, or both. A declaration to that effect must be included on the label, and starch may be added to a maximum extent of 5%.
18.2 Classification
Some of the frozen desserts can be classified as follows.
1. Plain: Plain ice cream has minimal coloring and flavoring, such as vanilla and coffee.
2. Chocolate: Chocolate ice cream is flavored with cocoa or chocolate
3. Fruit: Fruit ice cream contains fruits like strawberry, apricot, pineapple, mango, or banana, which may be fresh, frozen, canned, or preserved.
4. Nut: Nut ice cream includes nuts like almonds, pistachios, walnuts, or cashews, with optional additional flavoring or coloring.

19.1 Introduction
Cheese is a product that is produced by coagulating curd from milk with rennet or similar enzymes in the presence of lactic acid produced by adventitious or added microorganisms. Following the shaping of the curd in a mould and the removal of a portion of the moisture, it is permitted to mature by being maintained at an appropriate temperature and humidity for a specified duration.The FSSAI defines cheese as soft, semi-hard, hard, or extra-hard products that are matured or unripened, have a whey protein to casein ratio that is not greater than that of milk, and can be coated with food-grade waxes or polyfilm. coagulating agents. During this procedure, flavor-producing bacteria and harmless lactic acid bacteria may be introduced. The separation of whey is facilitated by the coagulation that results, which also ensures that the cheesemaking process concentrates milk proteins, particularly casein. Consequently, the protein content of cheese is substantially higher than that of the initial milk material blend. Furthermore, cheese-making incorporates methods that result in a final product with comparable physical, chemical, and sensory attributes by coagulating milk proteins or milk-derived products. The ingredients of cheese are limited to those that are naturally present in milk, with the exception of certain additives such as coagulating agents, sodium chloride, and small quantities of calcium chloride, annatto or carotene colourants, and specific emulsifiers and stabilisers such as citric acid, sodium citrate, sodium salts of orthophosphoric acid, and polyphosphoric acid. The wax employed for coating must not present any health hazards, and if it is coloured, it must be made from only approved food colours. The moisture content of hard cheeses is determined by the presence of no less than 42% milk fat and no more than 43% moisture on a dry matter basis. Additionally, they may contain trace quantities of nisin and ascorbic acid or its salts.

25.1 Introduction
Cream, butter, anhydrous milk fat, ghee and fat preserves, cheese, condensed milk, evaporated milk, skim milk, and whole milk powder are among the dairy products that have been extensively examined.
25.2 Defects in market cream
In the market, there are a variety of creams, including half cream, single cream, coffee cream, cultured cream, whipping cream, heavy whipping cream, aerosol cream, double cream, clotted cream, and high-fat creams (also referred to as plastic cream). The defects related to market cream are detailed in Annexure-I
1. Flavour defects in cream: Any flavor imperfections originally present in whole milk may become more noticeable in separated cream. Volatile compounds that are fat-soluble tend to concentrate in the fat portion, which can amplify these defects, such as an oxidized taste. Common flavor defects associated with cream include feed, cooked, malty, musty, utensil, weed, acid, bitter, and oxidized/rancid flavors. These flavor defects are further described in the section discussing flavor issues in Table butter.
2. Specific defects in cream
• Serum leakage, creaming, reduced overrun in whipping cream: Serum leakage typically results from partial churning (overwhipping), causing an unattractive liquid pool around the whipped cream or sogginess when applied to cakes. Excessive whipping leads to the formation of large fat globule clusters, which can break bubble-enclosing membranes, initiate bubble coalescence, and reduce overrun. This process may lead to an irreversible phase inversion, turning the cream into a greasy water-in-oil emulsion, visible as butter granules. Unfavorable creaming and serum separation can be delayed by lowering fat content (within legal limits), adding stabilizers like carrageenan, emulsifiers, or protein ingredients, or through post-UHT homogenization. Using a mix of kappa and iota carrageenan can help reduce creaming during storage and minimize whipped cream drainage.

ICAP : It stands for International Centre for Alcohol Policies.

Ice Bank Cooler : Air forced cooler leads to desiccation of the produce. So use forced air high humidity cooler are known as Ice Bank Cooler. Ice bank Coolers are useful for strawberry.

Ice bank cooling : Storing of fruit and vegetable in storage chamber with positive ventilation and a system countries where ice formation is allowed during night time (as electricity cost of night is less as compared to the day time). Melting of ice occurs during day time and with proper air circulation by means of ventilation process, approximately 0.5-1^ºC temperature with 90% RH in the chamber is maintained.

A healthy life is ensured by having access to safe, nutritious and balanced food. World health organisation (WHO) ensures its contribution in developing food safety systems that are sustainable to reduce health risks from farm to consumer. Thus, safe food, its quality and consumer protection are the priorities of this organisation (FAO and WHO, 2021)

L - Ascorbic acid: It is a white crystalline compound with a slightly acidic taste. It is readily soluble in water, alcohol, glycerin, propylene glycol and is insoluble in oils, fats, ether, benzene, chloroform.

Lab coat: A loose white coat with deep pockets that is worn in a laboratory or medical office.

Labeling: It means any written, printed or graphic matter that is present on the label, accompanies the food or is displayed near the food, including that for the purpose of promoting its sale or disposal. After packaging, labels are required on the finished products intended for distribution and sale. Labeling can reflect on the quality of the product. It must be clear and informative. Information includes Name of the Manufacturer, Date of Manufacture, Net Weight, Gross Weight, Best before etc. Proper storage is needed for maintenance of the quality. Storage must be done only at recommended temperature, relative humidity, light and air / oxygen and carbon dioxide conditions etc. to maintain the quality of the food product. Label may include tag, brand, and pictorial or discriptivematter, written, printed, embossed, graphic, perforated, stenciled or stamped impressions. It is attached to container, cover, lid, or crown of ant food package.

Food Science is one of the ancient sciences and the genesis originates to the very beginning of human civilization. The advent of food science was associated with practice and observation by humans before establishment of scientific concepts. The ancient man knew that roasting or smoking of meat improves the edible quality and digestibility. As a consequence, he started practicing the same much before the reasons for the same could be established. Many of the modern preservation concepts had their origin in prehistoric period itself as humans could use techniques such as dehydration, fermentation and pickling to their advantage to improve the sensory attributes of the products and also to enhance their shelf life. Humans during the Pre-Neolithic period about 2,50,000 years before used fire for cooking meat. During the Paleolithic period humans not only roasted food but also developed grinding, pounding and drying. During the Mesolithic era, humans were desperate for food and got involved in extensive hunting and fishing. During the same time domestication of animals took place and animal husbandry became a reality (Stewart and Amerine 1982). The Neolithic period made qualitative changes in the food habits of humans and they changed from a food gathering and hunting society to one of food production (Heizer and Elsasser 1980).

INTRODUCTION

For thousands of years fermentation processes were largely natural phenomena exclusively identified with food preservation throughout the world. Fermentations can play a significant role in meeting the ever growing food requirements of world population providing benefits in the form of innovative food products with improved nutritional value and food quality along side better safety. Fermentations can be used to address a large variety of food related problems and in the development of processes to meet the demand for food. In the wake of estimations made by international organizations that global food demand and population would increase by two-fold by the year 2050, much emphasis has been placed over the ways and means to increase food production and preservation.

L - Ascorbic acid : It is a white crystalline compound with a slightly acidic taste. It is readily soluble in water, alcohol, glycerin, propylene glycol and is insoluble in oils, fats, ether, benzene, chloroform.

Lab coat : A loose white coat with deep pockets that is worn in a laboratory or medical office.

Probiotics are measured in colony forming units (cfu). CFUs are generally measured in the millions or billions per serving. Probiotics are most commonly beneficial bacteria, but can also be friendly fungal or other organisms, that are typically freeze dried to stabilize them in an inert state during storage and production. Then their continued stability and viability, as measured by CFU counts when cultured, is dependent on limiting their exposure to stimulating environmental conditions such as temperature and moisture. Besides refrigeration, this protection can be done by packaging in glass or by adding freshness packets that helps to absorb and reduce moisture in the package.

Introduction

Since 1990, there has been a lot of interest in functional foods and nutraceuticals, particularly because of their impact effects on human health and the prevention of certain diseases. Apart from growing good quality natural products, there are challenges in extracting, refining, analyzing active ingredients, and evaluating safety before an effective, reliable product is made [1,2]. Special attention needs to be focused on separation and purification mainly because 40-80% of the cost of production is assigned to separation and purification unit operations in making functional foods and nutraceuticals. There are also several carotenoids and polyphenol products that have been identified from various plants and a single plant could contain highly complex profiles of these compounds. These are labile to heat, air, and light, and they may exist at low concentrations in the plants. This makes the separation and detection of nutraceuticals a challenging task. The membrane techniques used for the separation of nutraceuticals from the natural products, as well as their applications and influencing factors are discussed in this chapter [3, 4].

Introduction
 
Diabetes shows a wide range of variation in prevalence around the world and it is expected to affect 300 million by the year 2025. In a prevention framework where banning policies and educational strategies lead the interventions, functional foods (FFs) with their specific health effects could, in the future, indicate a new mode of thinking about the relationships between food and health in everyday life. Functional ingredients, such as stevioside, cinnamon, bitter melon, garlic and onion, ginseng, Gymnema sylvestre and fenugreek, have been addressed for their specific actions towards different reactions involved in diabetes development. New strategies involving the use of FF should be validated through large scale population trials, considering validated surrogate end points to evaluate the effect of FF in prevention of chronic diseases such as type 2 diabetes mellitus.

Physical Chemistry of Foods

    1.    Thermodynamics is primarily concerned with energy and entropy. Energy, also called internal energy (U), comprises heat and work; it is measured in joules (J).

    2.    Energy may be recalled that work generally equals force times distance (in N_·m = J) and that force equals mass times acceleration (in kg ·m· s^-2 = N).

    3.    According to the first law of thermodynamics, the quantity of energy, i.e., heat (q) work (p) potential energy, is always preserved.

    4.    Entropy (S)  is a measure of disorder; it is given by   
        S = K_B ln Ω
        Where K_B is the Boltzmann constant (1.38 ×10^-23 J × K^-1) and W is the number of  ways in which the system can be arranged, also called the number of degrees of freedom.

    5.    Colligative solution properties : The lowering of the chemical potential of a solvent by the presence of a solute causes changes in a number of physical properties: vapor pressure, boiling point, freezing point, osmotic pressure, etc. (the magnitudes of these changes all are proportional to the mole fraction of solute).

Importance

The dairy products, which have originated in India, are called indigenous dairy products. The products can be broadly classified in to khoa based and channa based. The importance of the dairy products were known to Indians since time immemorial or it could be roughly estimated to be around five thousand years ago and the development could be considered as an art.

“Tell me what you eat and I will tell you what you are. The destiny of people depends on the nature of its diet.”

A. Brillat-Savarin

Milk is the only product which is considered nature’s almost perfect food. It is treasure house of unlimited nutrients. It is considered best and ideal food by virtue of possessing almost all the nutritional factors, viz., fats, proteins, carbohydrates, minerals and vitamins. They are not only of higher quality but are present in milk in such form and proportion that their digestion and assimilation in the body is very efficient. Milk also plays a supplementary role in our nutrition. If it is included in our diet it enhances digestion and assimilation of nutrients of other food products. This is the reason that it is kept in high esteem as a food and is called the nectar for living beings.

Milk is the first taste of food for whole mankind. It establishes the mother-infant bond and is a life promoter. Of the many fluids that biology offers milk is perhaps the most versatile in terms of its use– as food, as a growth stimulant and as a defense package to the user. To the infant mammal – be it a mouse, calf or a human child, mother’s milk is more than a source of energy and nutrients. It contains a wide variety of substances that defend the growing infant against infections.

Milk, a perfect blend of nutrition and palatability, plays an important role in preserving mental and physical health. Milk has long been recognized as the most wholesome and complete single food available in nature for health and as a medicine, both preventive as well as curative. Ancient chronicles as recorded in the Upnishads, Puranas and Vedas extol the beneficial and therapeutic properties of milk and milk products. It has been stated that cow milk, dahi and ghee impart knowledge and radiance, cure heart trouble and anaemia besides other bodily diseases.

Milk is a complex colloidal dispersion, the physical and physicochemical properties of which depend on intrinsic compositional and structural factors, extrinsic factors such as temperature, and post-milking treatment.

There is no clear dividing line between physical properties and physicochemical properties. However, physical properties may be thought of as the measure of the bulk behaviour of milk and of how milk interacts with energy, while physicochemical properties are measures of how bulk behaviour and energy interactions depend on the constituent colloidal particles, molecules, atoms and ions in milk.

Knowledge of physical properties is of importance particularly in the technological and engineering design and control of milk processes and processing equipment. Knowledge of physicochemical properties provides the basis for the design of modern methods of milk analysis, determination of milk microstructures and elucidation of the complex chemical reactions that occur in milk.

In the dairy industry measurements of the physical properties of milk and milk products are made to secure data necessary for the design of dairy equipment (e.g., heat conductivity and viscosity) to determine the concentration of a component (e.g., specific gravity to estimate solids-not-fat or freezing point to determine added water), or to assess the extent of a physical or chemical change (e.g., titratable acidity to follow bacterial action or viscosity to assess aggregation of protein micelles or fat globules). The great advantage of physical measurements for such purposes is their speed and simplicity as well as their potentialities for automation.

Use of physical property to measure concentrations or changes in degree of dispersion demands knowledge of the contribution of the several components to that property. Furthermore, the natural range of variation of the property in milks or products is of major interest. The precision and suitability of possible methods of measurement are also of prime importance.

What is Performance Appraisal?

Performance Appraisal (PA) is the process through which an individual employee’s behaviour and accomplishments for a fixed time period are measured and evaluated. The major purpose of measuring and evaluating is to assess the worth or value of an employee. Performance appraisal is a systematic and objective way of judging the relative worth or ability of an employee in performing his task. Performance appraisal helps to identify those who are performing their assigned tasks well and those who are not and the reasons for such performance.

Milk processing plants involve processing of raw milk into products like market milk, cheese, butter, ice cream, condensed milk, dried milks and traditional dairy products. The by-products processing includes buttermilk, whey and its derivatives. Dairy effluents contain dissolved sugar, protein, fat and minerals. Spills and leaks of products or by-products, residual milk or milk products in piping and equipment before cleaning, wash solutions from equipment and floors, condensate from evaporation processes and cheese trimmings are some of the sources of dairy effluents in a dairy plant. The key parameters are the biological oxygen demand (BOD), chemical oxygen demand (COD), total suspended solids, total dissolved solids etc. Common dairy waste techniques include grease traps, oil water separators for separation of floatable solids, equalization tanks. Biological treatment consists of aerobic and anaerobic process.

Mushrooms are most ancient, best known and greatly admired fleshy macrofungi. Mushrooms are delicacies, much sought after and greatly valued foods. Wild mushrooms are mostly found in forests, tree trunks, pastures, lawns and road side during winter season and appear at surprising speed. Mushroom hunting or gathering is a popular hobby in Western countries. The wild mushrooms may be edible or unpalatable or poisonous. Poisoning by wild mushrooms is common and may be fatal or produce merely mild gastrointestinal disturbance or slight allergic reaction. The term toad stool is popularly reserved for inedible or poisonous mushrooms, but this classification has no scientific basis. This alarming term keeps many people away from these foods. It is important that every mushroom intended for eating be accurately identified. Mushrooms vary in colour, size, shape, growth habit, yielding ability and other characteristics.

STRUCTURE: Mushrooms are the fleshy fungi which constitute a major group of lower plant kingdom. Mushroom is the conspicuous umbrella-shaped fruiting body (sporophore) of certain fungi of the order Agaricales in the class Basidiomycetes but also of some other groups. Popularly, the term mushroom is used to identify the edible sporophores. The edible reproductive part consists of a stem and a cap. Gills found on the underside of the cap, are arranged like spokes in a wheel. The gills bear multiple spores which start new fungi. The sporophore emerges from an extensive underground network of fine thread like white growth known as mycelium. The mushroom, fruit body produced basidiospores at the tip of club like structures, called basidia, which are arranged along the gills of the mushroom. Beneath the mushroom, in the soil, is the mold colony itself, consisting of a mat of intercoiled hyphae, sometimes several feet in diameter. The mushrooms first appear as white tiny ball consisting of short stem (stipe) and a cap (pileus) which begins to open up like an umbrella. The delicate membrane or Veil (velum) enveloping the cap tears off, if allowed to develop fully, and lamellae (gills) radiating from the stalk into the cap become visible. These gills become darkened as the basidiospores (seeds) develop into millions and fall in the ground for starting their life cycle once again for second generation of mushrooms.

11.1. FRUITS-Maturation, Ripening and Storage

Fruits are natural foods containing substantial quantities of essential nutrients and the best sources of minerals like sodium, potassium and magnesium, vitamins (antioxidants), such as vitamin A, C and enzymes. They are rich in fructose and water. Fruits are living biological entities that perform a number of metabolic functions. Two functions of particular importance in fruit processing are respiration (the breaking down of carbohydrates, giving off carbon dioxide and heat) and transpiration (the giving off of moisture). Senescence is the period when chemical synthesizing pathways give way to degradative processes, leading to aging and death of tissue. Fruit ripening is thus the result of many complex changes, some interactive but many independent of one another. Once the fruit is harvested, respiration and transpiration continue, but only for as long as the fruit can draw on its own food reserves and moisture. It is this limited ability to continue vital metabolic functions that defines fruit as perishable.

Microorganisms (or microbes) are organisms too small to be seen with the naked eye. The science of microbiology is the study of microorganisms, their properties, classification, growth requirements, method of reproduction and distribution in nature. These organisms range in size from tiny viruses to larger bacteria, protozoa, algae, fungi and some of the microscopic worms (helminthes). They are present everywhere in our environment, in our homes, on our bodies, on the things we touch and on the food we eat. They are important for human survival on Earth, playing an essential role in many processes that maintain life. In nature, microorganisms carry out a number of important functions.

1.They are responsible for the decomposition of organic matter.

2.Recycling of nutrients that help to maintain the balance of chemicals in the soil.

3.Special nitrogen-fixing bacteria live symbiotically with certain plants, absorbing nitrogen from the air and converting it into compounds which can be used by the plant for growth.

4.Some algae are capable of photosynthesis, using energy from the sun to convert carbon dioxide in air into carbohydrate.

5.Marine microorganisms form the basis of the food chain in lakes, rivers and oceans.

6.Certain microorganisms are used in the manufacture of food.

7.Pharmaceuticals and drugs.

8.Industrial processes.

9.A valuable tool for scientific research.

10.Use in laboratory experiments to understanding metabolic pathways and in the discovery of the genetic code.

Growth of a microorganism implies an increase in amount of protoplasm, formation of new structures and eventually formation of new cells. Balanced growth means cell components increase in proportion to each other and unbalanced growth means cell components increase in a non constant relationship to each other

Microbial growth and growth curve

Phases of growth

When bacteria are grown in the laboratory in liquid medium, the medium becomes cloudy or turbid. It is possible to measure the increase in numbers of bacteria at various time intervals and plot the values on a graph representing a growth curve.

Lag Phase: When cells are first inoculated into fresh medium containing all the nutrients they require, they take a short time to adapt before they start to divide. This is termed the lag phase.

Sterilization is defined as the process by which an article, surface or medium is freed of all living microorganisms either in the vegetative or spore state.

Disinfection means the destruction or removal of all pathogenic organisms, or organisms capable of giving rise to infection. Chemical disinfectants which can be safely applied to skin or mucous membrane and are used to prevent infection by inhibiting the growth of bacteria are called antiseptics.

Five main methods are used for sterilization. 1. Red heat (flaming) 2. Dry heat (hot air) 3. Moist heat 4. Filtration 5. Radiation.

The killing effect of dry heat is due to protein denaturation, oxidative damage and toxic effect of elevated levels of electrolytes. The lethal effect of moist heat is due to the denaturation and coagulation of protein. In the case of spore, steam condenses on it, increasing its water content with ultimate hydrolysis and breakdown of the bacterial protein.

Physical Methods of Food Preservation

Conditions too stressful for microbial growth can damage cells. Food environments can be manipulated to inhibit or kill microbes. Physical manipulation of foods can inhibit microbial growth, kill cells, or mechanically remove them from the food. Dehydration, refrigeration, and freezing inhibit microbial growth. Microbes can be killed by heating or ultraviolet (UV) or ionizing radiation. Non thermal energy is also lethal. Membrane filtration removes microbes from liquid foods. This chapter discusses all these physical preservation methods

Physical Dehydration Processes

Drying

When foods are being dried, hot air evaporates the water and carries it away. Both the drying temperature and the decreased water activity (a_w) affect the microbes.

During the initial period of drying, the temperature is still low and the relative humidity is high. The size and composition of the food particle determine the length of this phase. If this particle size is large and the material is dense, this phase can be long, allowing microbes to grow. During later phases of drying, the temperature is high but the relative humidity is low. This provides no opportunity for growth but is not very lethal either. The higher temperatures result in lower moisture content, and dry heat is less lethal than wet heat. If the drying lasts long enough (at least 30 min.), there are time-temperature combinations that kill microbial cells. With certain drying methods, the surface temperature may reach 100°C, while internal temperature remains lower. This kills surface microbes, but not those in the food’s interior.

14.1 Introduction

The increasing human population and changing life styles have resulted in a huge demand for processed and packaged foods. As a result of this demand, large amounts of water, air, electricity and fuel are consumed on a daily basis for food processing, transportation and preservation. Although not one of the most heavily polluting, the food industry does contribute to the increase in volume of waste produced [1]. There is an increasing pressure from regulatory bodies through incentives, legislation and financial penalties to minimize waste generation and encourage adoption of eco-friendly options for waste management. Nanotechnology is a panacea for food waste management.

Abstract

The aim is to review the potential health benefits of minor millet. There is in need to identify newer sources of nutraceuticals and other natural and nutritional materials with the desirable functional characteristics. They are an important staple food in India for people of low income groups. Minor millet is rich in several nutrients as well as non-nutrients such as phenols. Nutritionally, its importance is well recognised because of its high content of calcium (0.38%), dietary fiber (18%) and phenolic compounds (0.3-3%). Minor millets, one of the cereals are known for several health benefits including its polyphenol and dietary fiber contents. Health beneficial effects include anti-diabetic, anti-tumerogenic, atherosclerogenic effects, antioxidant and antimicrobial properties. The energy of minor millets is greater than other cereals and nearly equal to that of brown rice because the lipid content is generally higher (3 to 6%). This review deals with the nature of polyphenols and dietary fiber of minor millets and their role with respect to the health benefits associated with millet.

Abstract

Re-constituted rice-premixes made by extrusion, has been successfully formulated for the fortification of market rice with vitamin A (retinyl palmitate and betacarotene) and iron. The statistics of vitamin A deficiency (VAD) and Iron deficiency anaemia (IDA) are alarming in the developing world, particularly in India. In fact, India is second largest producer as well as consumer of rice in the world, so fortification of rice with vitamin A and iron seems to be a successful solution to reduce the VAD and IDA in India. In order to design the final formulation, eight formulations containing target micronutrient profile were tested for vitamin A (both retinyl palmitate and beta-carotene) and iron retention for a period of six months under ambient (24-26 ⁰C) and elevated temperature (40 ⁰C) conditions. Nonsignificant iron loss was observed during six months of storage time under both ambient and elevated conditions. The higher retention of retinyl palmitate and beta-carotene was observed in formulation 5 and 8 respectively. In F5, the retention of retinyl palmitate was 73% and 66% and in F8, retention of beta carotene was 70% and 63% under ambient and elevated temperature conditions respectively after six months of storage. Substituting the original, vegetable shortening with palm shortening resulted in increased retention of retinyl palmitate and beta carotene in formulation 5 and 8. Thus, increased antioxidant effect of natural antioxidants in palm shortenings contributed to stability of micronutrients.