eChapters

Materials Required

Canned product, weighing balance, can cutter, vacuum/pressure guage, seam checking guage, Refractometer / Salometer etc. 

Procedure

    1.    Take a canned product say canned peach.
    2.    Record the weight of the can (A)
    3.    Record the information marked on the label i.e net  weight, date of packing, etc
    4.    Observe the can externally for the concavity of the lid.
    5.    Record the vacuum of the can by using a vacuum guage
    6.    Cut the lid of the can with a can cutter
    7.    Record the head space
    8.    Put all the contents over a sieve and let the liquid drain
    9.    Record the weight of empty can (B) to calculate net contents
    10.    Record the drained weight of the pieces.
    11.    Record whether the liquid is syrup or brine
    12.    Record the TSS of the salometer reading of the liquid (as the case may be)

A cut-out examination is conducted for the evaluation of canned fruit and vegetables and other products for various quality attributes, viz., physical, chemical, sensory, and microbiological attributes. The examination is conducted by following the undermentioned steps: External/physical examination of unopened Can
1. External Appearance of the tin can: Note the external condition of the tin can like dents, rusty spots, scratches, leakage around seams, and the condition of ends. Based on external appearance describe the condition of the tin can by using the following terms:
i. Flat Can: A can where both ends are concave. The vacuum is high enough to maintain the ends concave.
ii. Flipper Can: A can where the vacuum is so low that mechanical shock will produce distortion of one or both ends.
iii. Springer Can: A can in which one end is distorted and the other end is flat and pressure on the convex end will cause the flat end to spring out when pressed.

Dahi: It is the product obtained from pasteurized or boiled milk by souring, natural or by harmless lactic acid or other bacterial culture. It is also called Curd (Plate 209).

Dairy: It is a room, building, or establishment where milk is kept and butter / cheese is made or it is the department of farming / farm that is concerned with the production of milk, butter, and cheese or an establishment for the sale / and distribution of milk and milk products.

Dairy husbandry: It deals with care, breeding, feeding, milking of the diary cattle and the production and sale of the milk. It is the economical management of a dairy, including looking after the dairy cattle breeding and proper disposal or sale of milk and milk products.

Dairy products: These are the milk preparation, including butter, cream, cheese, ghee, yoghurt, pasteurized milk, tonned milk, butter milk etc processed and prepared in dairy. Ice cream and kulfi or sweets are not included in this.

Damage: Damage is a physical spoilage, often a partial deterioration, are subjectively judge and very difficult to measure and usually reported as per cent damage.

Daminozide: It is a growth regulator which is used for red colour development in apple.

1. Introduction

Milk and milk products constitute essential dietary components for a vast majority of the population. India with annual production of more than 135.6 million tonnes has emerged as leading milk producing nation. The per capita per day availability of milk in India is more than 290 g. Buffalo milk accounts for 57% of the total milk produced in India. Ethnic dairy products account for 90% of all dairy products consumed (Aneja et al., 2002). Many health benefits have been attributed to fermented dairy products and probiotic microorganisms (Salminen et al., 1998). The market for functional foods, nutraceuticals, wellness foods and beverages is fast growing. The harmful effects of synthetic drinks have propelled health conscious consumers to go for natural and traditional drinks. In search of better returns, the Indian dairy industry is widening its focus to include traditional milk products, and these are emerging as new profit centres for the organised sector.

Traditional dairy products have several advantages. They require low capital investment and give high profit margin. They are more appealing to the Indian palate. Dahi or curd is the most popular indigenous fermented dairy product. There are numerous references to dahi in vedic literature. The Prevention of Food Adulteration Act (Anon, 1976) describes dahi as a product obtained from pasteurized or boiled milk by souring (natural or otherwise), using harmless lactic acid or other bacterial cultures. Indian dahi and its western counterpart yoghurt differ considerably in terms of cultures used and their bouquet and flavour profiles (Aneja et al., 2002). The major flavor compound in dahi is diacetyl. Dahi made from buffalo milk has a firm body and white glossy appearance, with a cream layer on top. Mixed mesophilic cultures of Lactococcus lactis subsp. lactis, Lactococcus lactis subsp. cremoris, Lactococcus lactis subsp diacetylactis along with Leuconostoc species are grown together for production of dahi.

Introduction
 
Dairy ingredients are of significant importance in the formulation of many food products. Additionally, the incorporation of dairy ingredients, comprehensively recognized by the consumer as “natural” intensifies the odds of success of packaged foods and adds functional properties of the dairy ingredients in the targeted product. Dairy ingredients can be extracted from fluid milk in the form of cream, butter, condensed milk, dry milk, cheese, and whey products [1]. They provide beneficial functionality to foods, such as delivery of key nutrients, water management, fat-holding capacity, emulsification capability, viscosity creation, gel formation, and foam generation apart from providing desirable attributes of texture and flavour. Various ingredients and claims associated with dairy foods are shown in Table 3.1.

The GOI is pushing to strengthen infrastructure for the production of quality milk, as well as for procurement, processing, and marketing of milk and milk products through the following Dairy Development Schemes:

6.1. Dairy Entrepreneurship Development Scheme (DEDS)

Dairy Entrepreneurship Development Scheme (DEDS) was started in September 2010. This scheme is being implemented through NABARD which provides financial assistance to commercially bankable projects with loans from Commercial, Cooperative, Urban and Rural banks.

Objective of the scheme

To generate self-employment and provide infrastructure for the dairy sector, to set up modern dairy farms and infrastructure for the production of clean milk, to encourage heifer calf rearing for conservation and development of good breeding stock, to bring structural changes in the unorganized sector so that initial processing of milk can be taken up at the village level, to upgrade traditional technology to handle milk on a commercial scale, to provide value addition to milk through processing and production of milk products.

1.1. Global Dairy Scenario

Global milk production is forecast at 852 million tonnes in 2019, an increase of 1.4 per cent from 2018 (DAHD, 2019) – a smaller rate of growth, reflecting downward revisions made for India and the European Union. Much of the anticipated output expansion will originate in India, Pakistan, China, the European Union, and Brazil, partially offset by declines in some countries including Australia, Colombia, and Argentina. In India and Pakistan, herd expansions drive output growth, while in China, farm efficiency improvements underpin higher growth. The output is increasing in the European Union, although slowly as dry weather limited the supply of milk during the summer, whilst rising dairy herds and stable milk prices are supporting higher production in Brazil. By contrast, the output may decline in Australia and Colombia due to dry weather, whereas in Argentina, rising feed costs and restrained consumer demand may dampen production. Elsewhere, in the United States, higher milk yields hold up the growth momentum, whereas, in New Zealand, favourable weather corroborates a positive production outlook (DAHD,19).

    1.    The heifer is bred (naturally or by insemination) before the age of two years.

    2.    The gestation period is nine months and one week.

    3.    After calving, the cow gives milk for 10 months.

    4.    1 – 2 months after calving the cow will again be bred.

    5.    The cow then continues to give milk for about 300 days. This period is known as lactation.

    6.    Milk should preferably be handled in a closed system, to minimise the risk of contamination. It must be cooled to 4 °C as soon as it is produced.

    7.    The content of protein, lactose and ash is somewhat higher in buffalo milk than in cow milk. Buffalo milk contains vitamin A, but lacks b-carotene, which is present in cow’s milk.

    8.    When milk and cream turn to butter, there is a phase inversion from an oil-in-water emulsion to a water-in-oil emulsion.

    9.    In milk, the whey proteins are in colloidal solution and the casein in colloidal suspension.

Ice cream defects can result from formulation imbalance, poor ingredient quality, processing deviations, inadequate freezing or hardening, packaging problems, storage conditions, and cold-chain failures. This chapter provides a systematic framework for understanding, classifying, diagnosing, and correcting defects affecting flavour, body, texture, melting, colour, appearance, packaging, and storage stability. It emphasizes that a visible defect in the finished product may originate much earlier in the production or distribution chain. Examples include iciness caused by slow freezing or temperature abuse, weak body associated with formulation or overrun, and flavour problems originating from raw materials or microbial activity. Defect analysis therefore becomes an important tool for troubleshooting, quality improvement, training, and preventive action.

INTRODUCTION

Drying or dehydration is defined as the removal of moisture from its initial level to a level which renders food materials safe for subsequent storage. It is a simultaneous heat and mass transfer operation in which heat is supplied externally to evaporate moisture and air is forced through the bed to carry away the moisture. Drying is the oldest technique to preserve food materials. Advantages of drying include reduction in water activity, enhancement of shelf life, maintenance of flavor and nutritive value, and reduction in packaging and transportation costs. When the water activity of the dried product is reduced to below 0.6, most microorganisms do not grow and the rates of other deteriorative reactions are substantially reduced.

Materials Required

Dehydrator, balance, thermometer, sulphur dioxide, blanching pan, fruits / vegetables, polythene or aluminium bags.

Procedure

    1.    Select sound fruits or vegetables 
    2.    Record their initial weight and wash them properly in plain water to remove any dirt or extraneous matter. 
    3.    Peel with stainless steel knife (as the case may be) and cut into thin uniform pieces or slices of  0.2-0.5 mm thickness
    4.    Blanch the slices in boiling water for 1-2 min. to inactivate the enzymes followed by immediate cooling.
    5.    Treat the slices with sulphur (sulphuring or sulphiting) in order to prevent darkening of the product during drying. 
    6.    Dry the slices in a mechanical air dehydrator at about 55 + 5oC temperature.
    7.    Record the weight of the product after every 2 hr till it becomes (almost) constant i.e. when there no more (significant) loss of moisture from the product.
    8.    Pack the product in ploythene or aluminium laminated pouches and seal them air tight. 
    9.    If it is to be converted into powder, the dried product can be ground in a grinder before packing.
    10.    Label the packages and store them in a cool dry place.
    11.    Plot the drying rate curve of the product on a graph paper and analyse it.
    12.    Record the initial and final moisture content of the product (as discussed in Exercise No. 19). 

Drying and dehydration are interrelated terms. Drying generally refers to the method of removal of moisture from the food under natural conditions such as sunlight and wind for example open sun drying, shade drying etc. Whereas, dehydration refers to a process of removal of moisture by application of artificial heat under controlled conditions of temperature and airflow. In this case single layer of fruit and vegetables, either whole or sliced after primary pretreatments is spread on trays which are placed inside the dehydrator or in the open sun for drying. In the dehydrator, the initial temperature is generally kept at 43oC which is then gradually increased to 66-71oC for fruits and 60- 66oC for vegetables. Dried grapes (raisins and monucca), apricots, dates, apple rings/cubes, Morchella (Guchhi), bael, aonla, fig, green peas, cauliflower, cabbage, onion, garlic etc are commercial products prepared by using drying.
Procedure for drying: Drying generally involves three stages: pre-drying treatments or pre-treatments, drying of commodity and post-drying operations such as handling, packaging and storage. The flow sheet for drying of fruit and vegetables is shown in Figure 1 and details of pretreatments for drying fruits and vegetables are shown in Table 1&2 respectively.

Drying is the oldest known method of preserving food. Drying or dehydration is removal of majority of water contained in fruit or vegetable. Although preservation is the primary reason for dehydration, it also lowers cost of packaging, storing and transportation by reducing both weight and volume of final product. In addition, dried foods add variety to our diets. In the process of drying, sufficient moisture is removed to protect product  from  spoilage. Processing should be done in such a way that food value, natural flavour and characteristic cooking quality of fresh material are retained after drying.

Introduction

Flowering plants (Angiosperms) are identified by their morphological characteristics like flower, fruit and seeds that help their taxonomic characterization into different species, genera, families and orders. The floral characters which are used for taxonomic characterization of plants include the type of inflorescences, perianth structure, floral symmetry, arrangement of floral leaves, type of androecium, stamens, gynoecium, carpel, ovule, etc. The type of fruit and seed also play important roles in taxonomic classification. In this chapter we will briefly discuss about various morphological features of flowering plants (in botanical terms) that are useful in taxonomy.

Nomenclature of Plant

Nomenclature of plant is the formal and scientific naming of plants. It is related to but distinct from taxonomy for grouping and classifying plants and provide botanical name.

The scientific/botanical nomenclature started with Species Plantarum by Carolus Linnaeus in 1753. Botanical nomenclature is governed by the International Code of Nomenclature for algae, fungi, and plants (ICN), which replaces the International Code of Botanical Nomenclature (ICBN).

ICBN and ICN

International Code of Botanical Nomenclature, (ICBN) was adopted by the VIIth International Botanical Congress held in Stockholm, July1950. While the International Code of Nomenclature for algae, fungi, and plants (ICN) was adopted by the XVIIIth International Botanical Congress held in Melbourne, Australia in July 2011.

Commercial ice cream represents a highly diversified category influenced by formulation, processing technology, regulatory standards, consumer preferences, cost structures, and market positioning. This chapter explains the meaning and characteristics of commercial ice cream, with particular attention to the Indian regulatory and market context. It examines major commercial product types, their compositions, ingredient functions, and differences from artisanal products. The chapter also discusses contemporary market trends and changing consumer expectations, including premiumization and alternative formulations. Quality challenges such as ice crystal growth, sandiness, shrinkage, weak body, coating defects, and cold-chain failures are considered, providing readers with a practical understanding of commercial ice cream production and positioning.

Introduction

Agriculture is the most important sector of Indian Economy. The agriculture sector accounts for 18 per cent of India’s gross domestic product (GDP) and provides employment to 50 per cent of the countries workforce. India has emerged as the second-largest producer of fruits and vegetables in the world. Formerly agriculture was more dependent on nature and all the operations were carried out manually, however new technologies have been developed to increase the production and productivity of crops (Rangbhal, 2018).

Bottom or demersal trawling continues to be one of the most important fishing methods of the world. In India more than 35,230 trawlers of various sizes ranging from 9 to 30 m L_OA with engine power ranging from 45 to 495 hp @ 2000 rpm are in operation. Trawl is a bag net towed through water to filter out fishes, the mouth of which is kept open horizontally by means of a beam or otter boards and vertically by means of floats and sinkers. Horizontal mouth opening is also effected by dragging the net from two boats known as bull trawling or pair trawling. The principle of trawling is the movement of the net under water filtering the water through the mesh in the netting, without either permitting the fish to escape or gilling them (Fig. 1). Trawl net is fabricated using polyethylene netting after cutting and shaping the panels as per the design

Concept: Operations conducted before and after harvest are essential components of the system for producing high-quality seeds. If enough care is not taken in the initial stage, there most likely won’t be any resources left to get high-quality seed. Like this, carefully produced, high-quality seed may lose a significant percentage of its worth if post-harvest management protocols are not adhered to. Its quality is highly correlated with soundness, fullness, and homogeneity of physical characteristics (size, shape, density, colour, and appendages), in addition to mechanical planting’s simplicity and improved crop establishment. Improving the seed that has been gathered and getting it ready for secure storage till needed are accomplished through the effective and efficient process of seed processing. To increase the quality of the seed lot, the goal of seed processing must be to optimize the physical properties of the seed and the constituents of the harvested seed mass. The three main steps in seed processing are conditioning, grading, and applying protectants or enriching with nutrients. These steps are completed in compliance with established protocols and standards (McDonald and Copeland 1997; Agrawal 1996; Jorgensen and Stevens, 2004). The distinct qualities of the crops and the surroundings are taken into consideration while adjusting the machines and operations.

Abstract

Designer foods are known by various names like medical foods, fortified foods, nutritional foods, nutraceutical foods, pharma foods etc. These foods are nutritious, maintain health and prevent diseases. Such foods must possess characteristics like modified composition; limit the presence of certain potentially harmful components and include certain desirable ingredients either naturally or by intentional addition. The term designer food emerged some years ago to describe foods tailored to specific concentration and proportion of nutrients that are important to health. These are designed and produced by using different approaches. The term ‘designer foods’ is subjected to change based on nutritional labelling regulations, new developments, consumer perceptions and expectations. Grain improvement through biotechnology emphasizes crop upgrading with a specific challenge to manipulate the endosperm composition in order to improve its intrinsic properties for diet and health. Breeding fruits with higher bioactive compounds for disease resistance and improved composition have stimulated interest in the nutraceutical and processing aspects of the fruits Nutritive and genetic interventions to alter milk composition for specific health and processing opportunities are gaining importance in dairy biotechnology. Designer eggs having modified fat provide choices with different nutritional benefits. The options suggested for designer meat and meat products are through production practices, post-harvest procedures and reformulation techniques. All these features of designer foods will be presented with suitable examples.

Food is an important item in the life of consumer as it has a direct bearing on the sustenance of life. The food safety or over concern on the health hazards was not considered as an issue until recently, particularly in the developing countries. This clearly indicates the shift in citizen’s mind from availability of food to quality of food. This along with the changes in the food habits and type of products available in the market for his consumption, the incidence of food borne illness across the globe and his concern for his health contributed significantly to the development of food safety in the food arena.

Until recently food safety domain and regulation were confined to the government and its regulatory machinery. The globalisation of food and food products and the passage of food across international borders paved way for the increased food safety concern across the globe and stressed the need for ensuring quality and safety of food in international trade. The incidence of food borne illness increased with increase in the appearance of more and more derived products started in the market (Sivapalasingam, Friedman, Cohen, & Tauxe, 2004; Tauxe, Doyle, Kuchenmüller, Schlundt, & Stein, 2010). The production along the value chain, from primary production to the retailing happen in the world under different agroclimate conditions, in varied production lines from sinle handler to community production to large scale mechanised production and such a diversity led to concerns in the food safety system (McCullough, Prabhu, & Kostas, 2008). The individual operators in the chain operates a food safety management system based on the availablity and to suit his requirement based on the basic principles laid down by natinal and International bodies like Codex Alimentarius Commission. Now when you see the market at large, has plenty of FSMS system which includes both from the governmental and private sectors. Therefore, Food Safety Management System (FSMS) is the result of the implementation of available and relevant quality assurance guidelines and standards availble and in the primary production it could be the implementation of good practices including good hygienic proactices, good aquacultural priactices which have proved effective in the food sector. On the production and trade sector this may include good manufacturing practices, good hygienic practices, probably including Hazard Analysis and Critical Control Point (HACCP) principles. In the process the FSMS may include essentially all the activites from equipment, procedures, programs, tools, organizational measures, and people necessary to execute the control and assuranceactivities aimed at ensuring chemical and microbial safety of fresh produce.