eChapters

Introduction

Over centuries, spices have been used as an important addendum for colour, flavour and preservation of foods. In addition, their medicinal and cosmetic utilities have been widely recognized (Purseglove et al., 1981; Srinivasan, 2005). All these benefits made them extremely desirable with an ever growing demand in the international market. India holds the title of the largest producer and exporter of spices with major share for pepper, capsicum, turmeric, ginger cardamom, seed spices, curry powders, spice oils and oleoresins. The other primary producers of spices includes China, Indonesia, Malaysia, Egypt, Turkey Brazil and Mexico while USA, Europe, Japan, East Asian and Middle East countries are their major importers.

Spices are made from diverse plant parts viz. rhizomes, barks, leaves, fruits and seeds and hence its processing methods vary depending on the raw material. However, the basic unit operations namely harvest, pre-treatment, drying, cleaning, particle size reduction, packaging and microbial decontamination in sequence remains common for the production of most of the spices. Inappropriate conduct of basic unit operations often lead to high microbial load, aflatoxin contamination, losses of valuable compounds, change in sensory characteristics, physical damages and incorporation of contaminants in spice products (Table 1). Moreover, spices being natural products, they may be fraught with a large number of microorganisms including several pathogenic species of bacteria and fungus depending on the prevailing conditions in their cultivation areas. In addition, poor food sanitation awareness and practices in spice producing countries may worsen their microbiological safety. Although spices are nonperishable in nature due to their low moisture contents after drying, they may act as a source of microbial populations upon contact with moist food products with no further thermal treatment. The outbreak of ‘salmonellosis’ in Germany (1993) due to contaminated paprika and paprika-powdered potato chips is an example. The aforesaid disadvantages related to conventional spice production may confound their international trade unless desired objectives of food safety management schemes such as International Commission on Microbiological Specifications for Foods (ICMSF) are met. Moreover, international agencies have set standard to guarantee safe spices and augment business interests of their adherents. For example, both the European Spice Association (ESA, 2015) and American Spice Trade Association have set a maximum level of 1% w/w extraneous matter in spices (ASTA, 2017). These challenges associated with the conventional production system may be effectively addressed by preventive risk management strategy by which suitable control measures are enforced at earlier phases of food chain prior to consumption. The control measures must guarantee that the level of contamination has not exceeded the maximum permissible limit at every phase of spice production from farm to table.

Introduction

The international fish trade increases day by day reaching to a tune of USD 151 billion in 2020 (FAO, 2022). Many developing countries like India gain benefits from this trade as income through net foreign exchange reached to a level of 8.09 billion USD in 2019-20. Seafood supplied by developing countries contribute to 77% of fish consumption worldwide. The European Union (EU) is the single largest market for fish and fishery products to a tune of 91.74 billion USD in 2022 as a consequence of an increased per capita consumption among its Member States. Spain, Italy, Germany and the United Kingdom are the largest importer of fish and fishery products.

To protect consumer health and to protect the territory from the introduction of animal and plant diseases, the European Community (EC) has laid down joint conditions for imports of foodstuffs. The Directorate General for Health and Consumer Protection (DG SANCO) is responsible for food safety in the EU. The import rules for fishery products are framed of high standards with respect to hygiene, consumer safety and animal health status. It is important that importing countries and food business operators (FBOs) must understand the fundamental principles and requirements of the European Food Law to ensure efficient and smooth imports. The EU system relies on Government to Government assurances without any intervention of any private type certification or standards. The Competent Authority (CA) in the country of origin is responsible for giving the official guarantees to the EU regarding compliance and conformity to all requirements of its legislation. The Export Inspection Agency (EIA) is the Competent Authority in India for issuing the required official guarantees for export of fish and fishery products. The EIA maintains a complete list of all establishments under its control.

Abstract

Microencapsulation has found great applications in food business. However, the technology remains aloof from being fully exploited. Microcapsules offer food processors a way to shield sensitive food ingredients, mask or preserve flavours and aromas and conversion of volatile food components into easy-handled solid ingredients (like powders, capsules etc). A number of naturally occurring and synthetic polymeric materials have been identified so far that possess the entrapping property and are categorised as GRAS materials. Numerous techniques have been developed for using these entrapping materials to encapsulate the sensitive food ingredients. Controlled release of the food ingredients at proper place and right time could be therefore a key practicality that may be provided by microencapsulation. With strictly fine-tuned and stabilized release characteristic, this method adds worth to the merchandise. The areas of interest in this field include the development of alternative and inexpensive polymers that may be considered natural or mimic the properties of natural polymeric materials, like Gum Arabic, Gellan Gum, Gum Karaya, Gaur Gum and Gum Acacia. Limitations in many of the encapsulation techniques have occurred due to high value of raw materials and production. This review is effectively committed to the, properties of encapsulating agents along with the emphasis on different techniques used for encapsulation in the varied fields like food technology, pharmaceutical, commercial engineering and biotechnology.

Introduction

Nutrition is the study of how food and nutrients affect the body’s health and well-being. It encompasses all aspects of food, from the food production, processing, consumption and digestion by the body. A balanced diet included all the essential nutrients such as carbohydrates, protein, fat, vitamins and minerals for maintaining good health. The recommended daily intake of nutrients varies depending on the age, gender and physical activity of a person. The nutritional need also varies depending on the lifestyle and medical condition of a person. The nutrition facts are based on recommended daily intakes for various nutrients, which vary based on factors such as age, sex, and physical activity. These facts are given on food packaging or label, providing important information on the serving size, calories, macronutrients and micronutrients, and other ingredients.

Nutrition labels are mainly intended to guide the consumer in food selection. Nutrition information provided on labels must be true and should not mislead consumers. Nutrition labelling regulations are provided by countries to help manufacturers. The Codex guidelines on Nutrition Labelling provide guidance to member countries to develop or update their national regulations and to encourage harmonization of national standards with international standards. According to it, no food should be described or presented in false, misleading or deceptive way. Nutrition labelling cannot solve nutrition problems, instead it is one of the elements of nutrition policy.

11.1. Nutrition Facts

Nutrition Facts means the nutritional information required for most of the packaged food in many countries giving the energy value and nutrients contained in the food. Nutrition facts labels are required by regulation similar to other types of food labels. It provides detailed information on the nutrient content of the food such as the amount of fat, sugar, sodium and dietary fiber.

INTRODUCTION

Food is the basic need of human beings. It gets spoiled primarily due to microorganisms and enzymes. Energy is required for microbial growth and enzymatic reactions. At low temperature, the rate of biochemical reactions is slow resulting in prolonged storage life of food. It must have been observed long back that food could be stored for longer period without deterioration during the winter months. Since then this principle is being used to extend the storage life of foods. A sea change can be observed in development of low temperature preservation technology. It has travelled a long journey to reach this stage; however, a major break through took place in twentieth century. Low temperature technology is of two types; refrigeration and freezing. In refrigeration storage, water is in liquid phase and temperature is maintained above freezing point. In freezing technology, the food is stored below freezing point and water gets converted into ice. The former is short term preservation due to slow growth of microbes and lower enzymatic activity while the later is long time preservation due to inactivation of enzymes during blanching and inhibition of microbial activity due to unavailability of free water and much lower temperature. Low temperature preservation is widely accepted and is of commercially important in food supply chain.

The history of plant growth regulation was knownfor many years before the time of Christ, when it was common practice in the Middle East to place a drop of olive oil on figs to promote development. The use of plant growth regulators (PGRs) to modify growth and flowering of pineapple began in 1930s. In eighteenth century when a carpenter was working in a greenhouse in the Azores Islandaccidently set fire to a pile of shavings. To the surprise of the grower who had thought his plants were ruined, they burst into flower instead of being damaged (Collins, 1960). In Hawaii, Rodriguez (1932) noticed in the pineapple fields that smoke from brush fires adjacent to the field caused premature flowering. The ingredients of smoke were subsequently found to be ethylene and acetylene, the unsaturated hydrocarbons. During the 1940’s, auxins were also shown to produce this effect,α-Naphthalene acetic acid (NAA), β-Naphthalene acetic acid (BNA), Fruitone and naphthaleneacetamide were the next forcing agent to become commercially used in pineapple. Since that time many works have been carried out with improving results like natural and synthetic compounds that alter function, shape and size of crop plants have been discovered. Today, specific PGRs are used to modify crop growth rate and growth pattern during the various stages of development from germination through harvest and post-harvest preservation. The use of regulating chemicals has become an important component of agro-technical procedures for most of the cultivated plants and especially for fruit plants.

Pineapple is an important tropical fruit crop of India introduced by Portuguese from Southern Brazil early in the 16th century. It is a versatile fruit acting as a rich source of nutrients in many favourite recipes. In addition, it is an excellent source of vitamins, minerals, and antioxidants,highlighting its role as anti-inflammatory, digestion, and immunity support.It resembles epiphytes where roots are sensitive to poor soil aeration (Joy and Sindhu, 2012). In the present day, the demand for pineapple is increasing gradually in different parts of the country. However, insect-pests infestation turns out to be one of the major impediments in its quantum of production.

Pineapple is infested by several insect pests like mealy bug, scale insect, thrips, fruit borer, white grubs, bud moths, midges, fruit flies, termites etc. during its entire crop duration. However, Mealy bugs appeared as the key pest of pineapple while otherslike scale insects, thrips and fruit borer could cause economic damage to the crop only under favourable environment. Therefore, emphasis must be given for development of suitableecofriendly management techniques by proper prophylactic (cultural, mechanical, biological etc.) and protective measures to reduce the insect-pest population below the economic damage through proper monitoring and regular survey of the crop field.Thus, this chapter emphasizes on the important insect-pests infesting Pineapple along with their appropriate management options.

4.1 Phases of technology transfer
To translate laboratory research into market ready product, it is important to understand steps or phases involved in this technology transfer process. The process typically includes six main phases, each with a different role (figure 9).
4.1.1 Research
Technology transfer begins with research, the critical stage of exploring and discovering novel knowledge, technologies, or innovations that may have potential commercial applications. The research phase can occur in academic institutions, research organizations, or private sector companies, often funded by public or private sources. Thorough research ensures that the technologies being transitioned are scientifically and technically robust, thereby increasing their potential for market success. Therefore, the research phase involves creating and evaluating new ideas, confirming their feasibility, and identifying IP prospects, all of which are key components of TT success.
4.1.2 Innovation disclosure
Innovation disclosure is the first formal step where the innovation is reported to the appropriate TTO or IP management team. This process ensures that the institution or organization recognizes the innovation and evaluates its potential for protection and commercialization. It includes following information:

Introduction

Chickpea (Cicer arietinum L. ) popularly known as Gram, Bengal gram, Egyptian pea, Chana, or Kabuli chana, Garbanzo bean is one of the first grain legumes to be domesticated by humans in old world (Van der Maesen, 1972). The genus Cicer belongs to the sub-family Papilionaceae of the family Leguminoceae (Bentham and Hooker, 1970) now popularly known as ‘Fabaceae’ and have chromosome number 2n = 2x = 16. The origin of the crop is considered to be Western Asia from where it has been transferred in India and other parts of the world (Rathore and Sharma, 2003). Importance of pulses is relatively more in our country as its contribution in nutrient supply is far more in Indian diet than that in Asia and world as a whole (Ali,2002).

Introduction

Agriculture is the most important sector of Indian Economy. The agriculture sector accounts for 18 per cent of India’s gross domestic product (GDP) and provides employment to 50 per cent of the countries workforce. India has emerged as the second-largest producer of fruits and vegetables in the world. Formerly agriculture was more dependent on nature and all the operations were carried out manually, however new technologies have been developed to increase the production and productivity of crops (Rangbhal, 2018).

Introduction

The drying of fruits and vegetables during the season of abundance in order to preserve them for consumption during season of shortage is an ancient practice. Thus, drying is one of the oldest methods of preservation of the food commodities. It is practiced from ancient times and is a very common method of preservation in the tropical countries like India where conditions are much more favorable for sun drying. All micro-organisms need moisture to grow. So the removal of water in the food is brought down below a certain level at which they are unable to grow. Moisture content from food can be removed by different methods like sun drying (very oldest method and most popular), solar drying, cabinet drying, mechanical drying, tunnel drying, poly tunnel drying, adiabatic drying, spray drying, osmotic drying, fluidized bed drying etc. Grains are mostly dried in the sun. The moisture content of the grains can be reduced to a limit that is safer for their storage by sun drying. Many fruits and vegetables can also be dried by using sun energy. Some coastal areas of the countries fishes are also dried by exposing to the sun. After drying, sometimes the dried products are converted into powder. However, these powders are very hygroscopic and should be packed in airtight. Mango powder is prepared by this technique, but expensive and not popular in India. Nowadays many artificial methods have been developed for removal of the moisture. The relationship between the moisture content and temperature of air during process is referred as Psychrometric relation. An instrument used to measure the humidity (Relative humidity) of the atmosphere is known as Psychrometer (Hygrometer). The residual moisture in vegetable should not be more than 6-8% and in fruits it should be in the range of 10-20%. The dried fruit can be used as such or after soaking while dried vegetable are usually soaked in water overnight and then cooked. Vegetable are considered to be dry when they become brittle. There are generally two drying methods for foods like 1) Natural drying and 2) Artificial drying. The preservation / stability of the dehydrated products is conferred by the abstraction of water, so that the product is unable to support the microbial growth, its chemical forms of deterioration is inhibited and the drastic reduction in the weight / volume facilitate easier handling and marketing. Among dehydrated products, dehydrated onions have largest share of 45%. India is the third largest exporter of the onions in the world next to the Netherland and Spain. Besides this, India exports dehydrated bell pepper, garlic and mushrooms.

The dairy processing industry in India deals mainly with the fluid milk and/or short shelf life products, despite India being the largest producer of milk in the world, with an output bordering the 110 million ton mark. This feature offers immense potential in the area of R&D in dairy processing in terms of value addition. The potential gains are many, including higher returns for producers and advantages in terms of health, therapeutic, nutritional and/or gastronomy for the consumers. However, the Indian Dairy Industry can amass possible benefits by being a global contender in trade only when its products are at par with those available in the rest of the world in terms of price and quality. It is evident from the post-WTO scenario that for sustainability, Indian dairy industry will need to maintain wholehearted commitment to quality management right from the farm to the consumer, shedding its inhibitions and resistance to changes.

9.1. WTO Agreements and Food Industry

The General Agreement on Tariffs and Trade (GATT) was formed in 1947 and lasted until 1994, when it was replaced by the World Trade Organization (WTO) in 1995. The WTO is the only global international organization dealing with the rules of trade between nations. It provides a forum for negotiating agreements aimed at reducing obstacles to international trade and ensuring fair deal for all, thus contributing to economic growth and development. Currently, there are 16 agreements to which all WTO members are parties and two agreements to which only some WTO members are parties. WTO currently has 153 members, of which 117 are developing countries or separate customs territories. The Head Quarters of WTO is at Geneva (Switzerland) and the official languages are English, French and Spanish.

Introduction

Increased awareness about the food safety and various adulterations or crises reported in food industries, the food quality and its safety has emerged as the most important features of the modern food processing and preservation. The important historical dynamics which raised the concerns of food safety were motivated by accidents related to food borne pathogens and chemical contamination during the food processing and distributions. Many times, the terms food quality and safety are interchanged however, there is a difference in terms of their perception by the consumers and manufactures. In past few years, the food safety has become the characteristic of food quality and has been regulated by various national and international agencies. The increased concerns about the safe, nutritious and high quality food has over the time forced the public authorities to engage the food industries to construct the quality management systems in order to improve the food safety and build the consumers believe and trust towards processed foods. Food quality is a broader concept which includes food health quality attributes along with parameters like sensory characteristics like taste, smell and convenience like food preparation (Röhr et al., 2005). The food qualities like nutritional, convenience and sensory are not requested by the public laws but are desired by the consumers. The management systems for the quality assurance have evolved over the time and now we have systems like HACCP. ISO 9000 and ISO 14000 in place which are well known quality management modules to ensure the elimination of food hazards. On a broader scale of trading food several technical agreements under WTO (world trade organization) have been made which provide equal opportunities to all countries to trade the goods however, it imposes the similar food quality standards across all the participatory members. The responsibility of food safety is directly connected with all the stakeholders of the food chain which include manufactures, processors, farmers, food handlers and finally the consumers. Food contaminations may be a result of poor manufacturing practices and poor storage and handling practices at any stage in the food chain. To ensure the safety compliances, national food regulatory models plays a significant role. The guidelines issued by FAO/WHO, 2003 are focused on the public organizations, as well as food control authority self-assessment to ensure highest food quality and its safety from farm to fork. The base of the assessment includes 6 factors viz. food inspection, food quality management, food safety, official food control laboratories, food legislation food and quality information, education and communication (Shukla et al., 2014).For effective implementation of the food safety and quality module the countries have developed various food laws and legal norms which states the principles to be followed for raw materials, their processing and distribution in order to achieve the consumer expectations as well as the hidden food safety concerns.

Introduction

It is the process of retaining food over a period of time without being contaminated by pathogenic organisms or chemicals and without losing its colour, texture, flavour and nutritious value. It involves preventing the growth of bacteria, fungi and other microorganisms, as well as retarding the oxidation of fats which causes rancidity

Objective

• To increase its shelf life, retaining original nutritional values, colour, texture, and favour.

10.1. Introduction

When it comes to packaging, plastics are still popular because of durability, versatility, economic production, and enhanced mechanical properties. However, with growing concerns about the impact of plastics-based packaging on the environment, edible and biodegradable packaging were introduced. The application of edible and biodegradable packaging promotes renewable resources, which greatly reduces environmental concerns and fulfil the packaging requirements. The sources employed to develop edible and biodegradable packaging are mainly plant-based biopolymers like cellulose, proteins, starch, and lipid. Moreover, the properties of the packaging material are decided by the proportions of these biopolymers. Hence, selecting a food commodity to be package is equally important as selecting suitable resources for the development of edible and biodegradable packaging.

12.1. Introduction

Food Packaging is a means to ensure safety and quality of food product throughout storage, transportation, handling, distribution, retailing, sales and in some cases till the intended use. International trades in food are generally guided by Codex Alimetarius Commission (CAC) (A joint body of World Health Organization and Food & Agricultural Organization). CAC works in harmonization within the context of food standards, food packaging and the applied rules. The mandate of Sanitary and Phytosanitary Measures (SPS Agreement) and Agreement on Technical Barriers to Trade (TBT Agreement) is to facilitate food trades and remove restraints at possible extent. Through these agreements, member countries have provision to apply quality and safety measures to safeguard the consumer. Such measures extend to every aspect of food and its packaging. On the other side, food packaging industries also progressed with sound technological advancement and sophistication in the last three decades. Innovations in food packaging attracted consumers due to convenience, availability, safety, quality and preservation throughout shelf life of the food product. 

Introduction

Carbohydrates constitute nearly 80% of the total dry matter of wheat kernel. Starch is the predominant form, with cellulose, hemicellulose and pentosans present in lesser amount. Starch is present in discrete granules within the cells of the endosperm. Starch content is available in the range of 65% to 75% and generally related negatively to the protein content. Starch structure is a crucial determinant of many end-product uses of wheat. While the amylose /amylopectin ratio is a useful descriptor of starch structure, a more complete analysis of the population of the molecules which constitute a particular starch is considerably more revealing. The molecules range from the high degree of polymerization (10⁷ – 109 glucose units) and heavily branched amylopectin population, to the lower degree of polymerization (103 -106 glucose units), and infrequently branched amylopectin population. Starches with widely differing structures are suited to particular end uses. For example, starches with no amylose, the so called waxy starches are particularly suited to use as thickeners or gel forming agents because they form a clear stable gel with little retrogradation. In contrast, starch with high amylose content form hydrogen bonded insoluble aggregations which are suited to use in adhesives, plastics and as a source of dietary-fibre starch. The size and branching pattern of starch are also important determinants of the suitability of starches for particular end-uses due to the effects these parameters have on gelatinization temperature, starch swelling and viscosity.

Introduction

Functional elements are non-conventional biomolecules in foods that have the ability to modulate one or more body metabolic processes or pathways, leading in health advantages and well-being promotion. Research has demonstrated a connection between food, health and well-being functional elements. Consequently, functional elements have health-promoting roles connected with multiple progressive steps at various phases of disease control, from initiation to growth. They can therefore be implemented efficiently in disease therapy and prevention. Therefore, the borderline between food and medicine is becoming very thin at a moment when the role of a healthy diet in stopping non-communicable diseases is well recognized. Functional elements include plant-derived, non-nutritious and biologically active chemicals that operate in the body to avoid certain non-communicable diseases from occurring.

Food contains over 900 phytochemicals. One fruit or vegetable serving (about 120g) can contain as many as 100 distinct phytochemicals. Previously, functional elements were believed to happen predominantly only as phytochemicals in plant products including whole grains, fruits and vegetables. However, in animal goods such as milk, fermented dairy products and cold water fish, probiotics, conjugated linolenic acid, long-chain omega-3, −6 and −9 polyunsaturated fatty acids and bioactive peptides are also discovered. Usually, functional elements happen in various forms in food such as glycosylated, esterified, thiolated or hydroxylated materials. They also have numerous metabolic operations that enable positive impacts in the body on several illnesses and target tissues (Balic et al. 2020).

Introduction

The state of Odisha highly depends on rainfall for the agricultural production. But rainfall distribution is very erratic and uneven which result heavy floods and droughts in different pockets of the state. Thus, the agricultural production is very unstable. It is present in the eastern region of India which is again located in the subtropical belt of medium pressure. Here hot and dry summer welcomes wet humid monsoon which last about few months. Charming autumn and with short and mild winter entertain the human life. But here climate is characterized by high temperature and medium rainfall. Topography however modifies the local climate greatly. The four meteorological seasons prevailing in the state which are: winter (January to February), pre-monsoon season (March to May), south-west monsoon season (June to September) and north east monsoon season (October-December).

Introduction

The art of fermentation process is developed as far back as thousand years ago without understanding the role of microorganism in it. It is believed that the process of fermentation originates in Indus valley during 7000 – 8000 BC. Archives of harappan civilization showed that different clay utensils were used for the fermented product and the agriculture and animal husbandry were fully developed during that period. It is evident from the artifacts of Egypt and middle east that the practice of fermentation was common in that part (Farnworth, 2003). The earliest practice of cheese making is originated from Falcate between Tigris and the Euphrates rivers in Iraq, 8000 years back. Later, Egyptians developed the use of yeast in wine and bread making during 4000 BC (Ross et al., 2002). Further, Sumarians prepared beer from fermented barley during 1750 BC. Earlier the fermenting process was an artisan way without any knowledge of microorganism. However, the main turning point was in 1608, when Antony Van Leeuwenhoek first established the use of a microscope and revealed the existence of microorganisms. Another, major finding was Pasteurization by Louis Pasteur in 1861 AD and this was the first report that documented the role of microorganism in fermentation. Later, there was a shift observed in the production of fermented food from local communities to large scale industry. The health effect of fermented food was first reported by Roman historian Pliny, who reported that fermented milk is beneficial for gastrointestinal complains. Further, a French paediatrician proved that Bifidobacteria in food prevents infants against infection (Grill et al., 1995).