eChapters

Introduction Soil ecosystems are the foundation of human life support systems. Soil erosion, loss of soil organic matter and nutrient depletion are among the leading contributors to impaired soil health, reduced crop yields and poverty. Realizing the significant role that soils play in food and environmental security and in abating climate change, the United Nations declared 2015 as the Year of Soils. The International Union of Soil Sciences (IUSS), in 2002, proposed to observe the 5th December as “World Soil Day” [WSD] to create awareness among all stakeholders on the importance of soil as a critical component of the natural system and as a vital contributor to human commonwealth through its contribution to food, water and energy security and as a mitigation of biodiversity loss and climate change. These occasions remind all stakeholders associated with agriculture all over the world to put in all efforts to promote scientific management of soil resources for soil protection, conservation and sustainable productivity.

Abstract

Recently, the reduction of post harvest food losses around the globe is a critical issue for ensuring future food security. Drying techniques is important option to prevent losses and preserve food for long time. The solar thermal energy required to remove moisture from the food during the drying process can be optimized by designing suitable solar dryers. Moreover, the application of solar energy in drying of agricultural products has tremendous potential, since it can easily provide the low temperature heating required for drying and helps in reduction of CO2 emissions. Hence, the present chapter deals with descriptions of different types of solar dryers used to dry various types of agricultural food products and design of solar dryers. Also, the heat and mass transfer parameters with respect to various process variables to estimate the performance of the food dryer system were analyzed. The advantages of solar dryers in terms of net CO2 emissions mitigation potential and the quality attributes of dried food products are also discussed. It is suggested that properly designed solar dryers having low operational cost compared to electrically heated dryers may prove to be an energy saving device for drying of agricultural products. However, the techno-economical and environmental aspects of various efficient solar dryers are needed to be further studied for applications in various irregular shaped food products.

Abstract

The primary commercial energy sources such as coal, oil and natural gas poses an enormous challenge to our development goals including environmental degradation, as India is not well endowed with these exhaustible natural resources. Further, these conventional sources are also not available in right quantity and producing environmental pollution manifold in land, air and water. There are number of unit operations in food processing and value addition consuming bulk of conventional energy sources where renewable energy sources can easily be integrated for energy conservation and environment protection. There is significant potential for application of Renewable Energy Sources in different unit operation of food processing including drying of food products for energy conservation and for reducing hydrocarbon emissions.

Percent Solutions

There are three types of percent solutions. All are parts of solute per 100 total parts of solution. Based on the following definitions you may calculate the concentration of a solution or calculate how to make up a specific concentration

    1.    % W/W - Percent of weight of solute in the total weight of the solution. Percent here is the number of grams of solute in 100 grams of solution. 
        Example: 
        A 100% (W/W) NaCl solution is made by weighing 100 g NaCl and dissolving in 100 g of solution

    2.    % W/V - Percent of weight of solution in the total volume of solution. Percent here is the number of grams of solute in 100 ml of solution. This is probably the least significant way of naming a solution, but the most common way of doing it. In fact, any percent solution not stipulated as W/W, W/V, or V/V is assumed to be % W/V. 
        Example : A 4% (W/V) NaCl solution is 4 g of NaCl in 100 ml of solution.

    3.    % V/V - Percent of volume of solute in the total volume of solution %V/V. Percent here is the number of milliliters of solute in 100 ml of solution. 
        Example: A 10% (V/V) ethanol solution is 10 ml of ethanol in 100 ml of solution; unless otherwise stated, water is the solvent. 

Food Safety and Standard Authority of India (FSSAI) has adopted the standards of Fruit Product Order (FPO).

Chutney

It is a product prepared by cooking the fruit pulp with added salt, sugar, spices, acetic acid and fruit to a suitable consistency so that it contains TSS not less than 50% and fruit part not less than 40% as per FSSAI specification. Sugar, salt, spices, acetic acid all act as partial preservatives. Preservatives may also be added in chutney for increasing its storability. Generally no artificial colour and flavor are required to be added.

Sauce

Sauce is a product similar to ketchup, prepared from pulps of tomato or other fruit/vegetable, having TSS not less than 15% and cooked to a suitable consistency with added sugar, salt, spices and vinegar. Sugar, salt, spices, acetic acid all act as partial preservatives. According to FSSAI specification fruit sauce should have minimum of 15% TSS and 1.2% acidity. Preservatives and colours may also be added for increasing of appearance and storability.

Abstract

Water, the most important component of common foods, is considered to be desirable as well as undesirable in the different food systems. Water-solid interaction in food systems controls various biological, biochemical and biophysical reactions affecting their acceptability. The retention or release of water from solid has been quantified in the terms of sorption isotherm. Sorption isotherm techniques have been used to characterize and identify the type of water-solid interaction in different food products. Sorption isotherm provides various information useful in designing and optimization of drying, storage, packaging, predicting quality and shelf life of the product.

8.1 Introduction

Spices are appetizers and hence, esse ntially used in the culinary preparations. They also possess antioxidant, antimicrobial and antibiotic properties. Further, they possess medicinal properties and hence, play an important role in human health.

According to International Organization for Standards (ISO), there is no clear cut division between ‘Spices’ & ‘Condiments’ and as such they have been clubbed together. The term ‘Spices’ & ‘condiments’ applies to “such natural plants or vegetable products or mixtures there of, in whole or ground form, which are used for imparting flavour, aroma and piquancy and seasoning of foods”. Spices are divided into different groups based on their plant components such as floral, fruits, berries, seeds, rhizomes, roots, leaves, kernel, aril, bark, bulbs etc.

About 70 spices are grown in different parts of the world and a major portion of these are grown in India. Hence, India is called “The home of Spices”. It is well known that spices played a significant role in ancient times, in the development of civilization – the life of the people and trade among the nations of East and West. Spices like ginger, pepper and turmeric have an intense and immediate impact on sensory perceptions and exhibit strong physiological effects as food and medicinal constituents. Some spices and herbs like cardamom, saffron and vanilla, which have less intense but more delicate sensory effects, are well known for their contribution to fragrance and usage as food flavouring agents. The history of spices and their use in food and medicine in ancient India have been reviewed earlier [1-3].

Introduction

Spices and aromatic herbs have been used since antiquity as preservatives, colorants, and flavour enhancers. Spices, which have long been the basis of traditional medicine in many countries, have also been the subject of study, particularly by the chemical, pharmaceutical, and food industries, because of their potential use for improving health. Both in-vitro and in-vivo studies have demonstrated how these substances act as antioxidants, digestive stimulants, and hypolipidemics and show antibacterial, anti-inflammatory, antiviral, and anti-carcenogenic activities. These beneficial physiological effects may also have possible preventative applications in a variety of pathologies. The chapter presents an overview of the potential of spices and aromatic herbs as functional foods ingredients.

Spoilage may be defined as the deteriorative process which renders the food inedible or results into reduction of quality.

Spoilage is Mainly of Two Types

Abiotic Spoilage: Less potential for causing health hazards to consumers. Occurs due to

Introduction
The food that has been damaged or has undergone changes so as to render it undesirable/unacceptable/unfit for human consumption is termed as spoiled. Spoilage of processed products is mainly caused by the action of micro-organisms and due to the physical or chemical changes. The reasons for microbial spoilage include under processing, inadequate cooling, contamination from leakage through can seams and pre-process spoilage. In under-processed cans (receiving low heat treatment), large number of different types of micro-organisms are expected to be involved in spoilage.
Causes of Food Spoilage
Food spoilage or deterioration may be described as loss of weight, softening, souring, rotting, wilting, moulding or a combination of one or more forms. The major causes of food deterioration are: biotic and abiotic factors.
A. Biotic Factors
1) Microbial spoilage (yeast, mould, bacteria)
2) Enzyme action (activities of enzymes present in foods)
3) Insect and rodent damage (attack of insects, rodents and parasites)

Introduction

Spray drying process has been used for decades to encapsulate food ingredients such as flavors, lipids, and carotenoids. During this drying process, the evaporation of solvent, that is most often water, is rapid and the entrapment of the interest compound occurs quasi-instantaneously. This required property imposes a strict screening of the encapsulating materials to be used in addition to an optimization of the operating conditions. Likewise, if the encapsulated compound is of hydrophobic nature, the stability of the feed emulsion before drying should also be considered.

Abstract

Spray drying is one of the most preferred methods of converting food and pharmaceutical solutions into powder form. Very high product throughput, hygienic and highly automated process and relatively benign thermal and dehydration stress on products associated with this process has made it ubiquitous in powder manufacture. Compared to freeze drying, spray drying is significantly less expensive both in terms of operation and capital costs. In this chapter, key features of spray drying such as underlying operational principle, types of spray nozzles used, the flow pattern of droplets/particles and drying medium within the drying chamber, the particle formation process of individual droplet are discussed in considerable detail. The modelling aspect of a single droplet subjected to spray drying environment has also been included. Finally, the most commonly considered characteristics of spray dried powders including morphology, crystalline/amorphous nature and solubility are highlighted and discussed.  The content presented in this chapter will be very useful for practising engineers, technologists, researchers as well as postgraduate and undergraduate students.

Stabilizers and emulsifiers are used in small quantities but have major effects on the structure and quality of ice cream. This chapter explains the differences between these two functional ingredient groups and describes their roles in controlling water mobility, fat destabilization, air-cell stability, texture, meltdown, and heat-shock resistance. It discusses commonly used stabilizers and emulsifiers, their individual characteristics, and the advantages of using blended systems. Particular attention is given to formulation balance and the defects that may arise from incorrect selection or dosage, including gummy texture, weak body, poor meltdown, and structural instability. Practical guidelines help manufacturers select and use these ingredients effectively for consistent product quality.

Abstract

The aim of this work was to reduce the natural fermentation period of ‘idli’ from the conventional 14 hr to10 hr by adding underutilized okara for the preparation of ‘idli’. Black gram was partially substituted with soy residue okara in the ratio of (1:1). After 14 hr of natural fermentation, the pH and total acidity of control ‘idli’ batter was 4.55 and 0.68% and that of okara fortified ‘idli’ batter was 4.57 and 0.56%, respectively. The amount of CO₂ released by the control and okara fortified batter was 12.5% and 22.5% respectively. The viable count of yeast and mold, lactics and mesophilic bacteria in control and okara batter increased with time reaching 8.4 and 9.6, 8.2 and 7.5, and 8.6 and 9.2 log10 cfu/g, respectively at the end of 10 hr of natural fermentation. Okara fortified ‘idli’ was soft and spongy compared to control ‘idli’.

STARCH : Starch is a complex carbohydrate that has been cursed by dieters in years past, but that now is praised by nutritionists as a particularly healthful source of energy. In food preparation at home starch is a very important as a thickening agent. However starch is but one of several polysaccharides that are used as thickners in the food industry.

STRUCTURE : Although starch is the name used by nutritionists this complex carbohydrate actually consists of two fractions amylose and amylopectin. The two fractions occur together in starch from most sources so the overall behaviour of starch is determined in large measure by the relative amounts of amylose and amylopectin. Each of the fraction has unique properties that contribute to the functionality of starch from various plant sources.

Starch is the storage form of carbohydrates in plants which is abundantly found in roots, tubers, stems, fruits, and cereals. It is a polysaccharide made up of glucose monomers with a chemical formula of (C6H10O5)n. Starch is composed ofamylose and amylopectin. The linear polymer amylose is the most basic form of starch while amylopectin is the branched form. Foods that are high in starch content are a good source of nutrition. Food starches are used in the food industry as thickeners and stabilizers. During the ripening of fruits, the starch is converted into sugars. Therefore, the presence of starch in fruits is used as an indication of maturity and ripening.
Principle: For estimation of starch contents, the sugars present in the sample are leached out and starch is hydrolyzed using either acid or enzymatic hydrolysis. Stach is then calculated as invert sugars.
Starch content by Acid Hydrolysis method
Reagents: Ethanol 95%, /50%,Concentrated HCl, Concentrated H2SO4, 1N NaOH solution, Phenolphthalein indicator, 10% alcoholic solution of Alphanaphthol.

Introduction

The state of Odisha highly depends on rainfall for the agricultural production. But rainfall distribution is very erratic and uneven which result heavy floods and droughts in different pockets of the state. Thus, the agricultural production is very unstable. It is present in the eastern region of India which is again located in the subtropical belt of medium pressure. Here hot and dry summer welcomes wet humid monsoon which last about few months. Charming autumn and with short and mild winter entertain the human life. But here climate is characterized by high temperature and medium rainfall. Topography however modifies the local climate greatly. The four meteorological seasons prevailing in the state which are: winter (January to February), pre-monsoon season (March to May), south-west monsoon season (June to September) and north east monsoon season (October-December).

Abstract

Agro-food industries generate a large amount of by-products and wastes. These byproducts and wastes have a negative impact in terms of the environmental concern due to the increase of pollutant disposal, and industrial sustainability because of high costs related to their management. These byproducts and wastes are rich in minerals, sugars and proteins. The composition and characteristics of wastes from different food processing industries vary and rely upon the production technique and the nature of the product. India is the second largest producer of rice/paddy in the world and the utilization of rice bran is gaining importance. However, a small fraction of these have been utilized. In case of fruits and vegetables, industrial processing of potato generates between 70 and 140 thousand tons of peels worldwide annually. Moreover, 37% of world’s total annual production of banana is shared by India. Hence, to minimize the disposal fees and trash collection new policies and methods have been developed for handling and treatment of wastes and byproducts. This chapter envisages the status of different agro-food industrial byproducts and wastes for the development of different food and non-food products.

Organic products are grown under a system of agriculture without the use of chemical fertilizers and pesticides with an environmentally and socially responsible approach. This is a method of farming that works at grass root level preserving the reproductive and regenerative capacity of the soil, good plant nutrition, and sound soil management, produces nutritious food rich in vitality which has resistance to diseases. India is bestowed with lot of potential to produce all varieties of organic products due to its various agro climatic conditions. In several parts of the country, the inherited tradition of organic farming is an added advantage. This holds promise for the organic producers to tap the market which is growing steadily in the domestic and export sector.

As per the available statistics, India’s rank 8th in terms of World’s Organic Agricultural land and 1st in terms of total number of producers as per 2020 data (Source: FIBL & IFOAM Year Book, 2020). The APEDA, Ministry of Commerce & Industries, Government of India is implementing the National Programme for Organic Production (NPOP). The programme involves the accreditation of Certification Bodies, standards for organic production, promotion of organic farming and marketing etc. The NPOP standards for production and accreditation system have been recognized by European Commission and Switzerland for unprocessed plant products as equivalent to their country standards. Similarly, USDA has recognized NPOP conformity assessment procedures of accreditation as equivalent to that of NOP of US. With these recognitions, Indian organic products duly certified by the accredited certification bodies of India are accepted by the importing countries. APEDA is also in the process of bilateral equivalence with South Korea, Taiwan, Canada, Japan etc.