eChapters

Introduction

“Quality” refers to the aesthetic appearance and freshness of fish. It also involves safety aspects such as being free from harmful bacteria, parasites or chemicals. The best quality fish is the one consumed within the first few hours after postmortem. We studied in our previous chapters that in some instances, even very fresh fish in rigor mortis are unsuitable for filleting. So, slightly older fish in post-rigor are more desirable for the processors.

The assessment methods of fish quality are divided into sensory, instrumental, chemical and microbiological. Sensory method is superior and all other methods must correlate with the results of sensory evaluation. So, sensory method must be done more scientifically under controlled conditions without the effects of test environment, personal bias, etc.

4.1. Sensory Methods

Sensory evaluation is defined as the scientific discipline used to evoke, measure, analyze and interpret reactions characteristics of fish, as perceived through the senses of sight, smell, taste, touch and hearing. There are few instruments capable of measuring sensory profile viz. Instron for texture, electronic nose for odour, microscopic imaging for structure, etc.

In sensory evaluation, appearance, odour, flavour and texture of fish are evaluated by the human senses. The process involves three steps: (1) detection of a stimulus by the human sense organs, (2) evaluation and interpretation by a mental process; and (3) the response of the assessor to the stimuli. The response of stimuli varies among individuals e.g. some people cannot taste rancid flavour and some have low response to cold-storage flavour.

Introduction

Agriculture is the main sector of the Odisha economy and contributes approximately 42% to the gross domestic product (GDP) and employs over 80% of the population. Despite its role, agricultural production is constrained by high climate variability where rainfall distribution is extremely uneven and this has negative implications for the livelihoods of people .Drought frequently results in crop failure, while high rainfall intensities result in low infiltration and high runoff causing enhanced soil erosion and land degradation. Land degradation in the form of soil erosion and declining land fertility is a serious challenge to agricultural productivity and economic growth (Lemenih, 2004).Studies indicate that the tribal district of Odisha have experienced high rates of soil erosion and deforestation, resulting in sediment accumulation in downstream reservoirs and rivers.

Introduction

Food safety and quality assumes paramount significance in any food industry. Globalization has driven both the food and agricultural firms to adopt systems that functions in a way to interlink food standards and international trade so as to achieve superior food quality and safety. Food industries follow several regional and international food safety procedures to procure certification from the government and other agencies in order to survive in both domestic and international markets (Ryan, 2014). The essential components in the food safety include handling, preparation and storing of the food products to ensure the food quality and to avoid food-borne diseases. The unwanted substances in a food product included by an accident is known as contaminants and the unwanted substance added to the food product to reduce the cost or to improve the other properties are known as adulterants. Contaminants and adulterants may lead to pathogens and toxins that pose serious concerns over the health of the consumer (Jha, 2016). The adulterants and contaminants are classified as physical adulterants and contaminants, chemical adulterants and residues, microbiological and pathogenic contaminants and toxins.

Hazards in food can be categorized into physical, chemical and biological.

Physical Hazards: Physical hazards are foreign organic or inorganic objects or extraneous materials in the food products. Hard and sharp physical hazards are of particular concern. Examples of physical hazards are broken glass, plastics, metal pieces, wood pieces, stones etc.

1. Introduction

In recent years, consumers have been demanding convenient, healthy and safe foods which have ’fresh-like’ characteristics with a long shelf-life. These demands include important food quality such as appearance, texture, taste and nutritional content which are strongly impacted by the way it is processed. Another major concern among the consumers is food safety and quality. The shelf-life of the food products are mostly influenced due to the action of various harmful microorganisms and enzymes. The conventional food processing technologies, such as thermal treatments (pasteurisation and high temperature sterilisation), evaporation, drying, frying and baking can assure the microbiological safety and/or stability of processed food products, but affects the food quality and nutrients (heat sensitive vitamins, flavour and other bioactive compounds) (Zhang et al., 2019)

Abstract

Drying is one of the most important industrial operations for preservation of food material. Due to the major limitations posed by convective drying methods, there is always a need for novel drying techniques which are technically, economically and environmentally sustainable. Based on the principle of moisture diffusion due to vapor pressure gradient, atmospheric freeze drying (AFD) offers a promising alternative to conventional drying systems. A cold gas with low water vapor pressure is used as drying medium to sublimate moisture directly from the frozen material at atmospheric pressure conditions. As a result the product gets dried at much lower temperature unlike convective drying. Thus, products dried with AFD retain better nutrition, texture and color and the process is also considerably cost effective. Major limitation of the AFD process is longer drying time, which can however be accelerated by using heat pump drying or new ultrasound technology. This chapter focuses on mechanism, benefits, limitations and comparative study of AFD with other drying methods such as hot air drying and vacuum freeze drying. It provides an insight regarding effect of AFD on properties of food material based on various studies reported in literature.

Previous Year Questions

1. No questions were asked in past 10 years

Availability of Foodgrains

• Net availability of foodgrains = Gross Production (-) seed, feed & wastage, (-) exports imports (+/-) change in stocks.

The avocado (Persea americana Mill) belonging to the family Lauraceae, may have originated in southern Mexico but was cultivated from the Rio Grande to central Peru long before the arrival of Europeans. It was then distributed into the West Indies and all other parts of the tropical and subtropical world. It reached India probably in 1892. Now it is grown in Tamil Nadu, Karnataka, and Kerala in India, to a limited extent.

Cultivars/Varieties: Fuerte, Hass, Lula, Pollck, Purple, Green.

Uses

Avocado is low in sugar content and rich in avocado butter, hence can be highly recommended as a high energy food for diabetics. The pulp of the fruit can be preserved by freezing, and can be used as sandwich filling or spread, in ice creams and milk shakes. Though the fruit is high in fat content, it is harmless unlike animal fat. The pulp has butter consistency, and looks very much like cow’s butter and bland in taste with a nutty flavour, without any offensive odour or smell. Its aroma resembles that of tender coconut.

B.T.U.: It stands for British thermal unit. The heat required to raise the temperature of one pond of the water through 1oF is called BTU (Plate 82).

Baby back ribs: Meaty pork ribs cut from the lower back rib section.

Bacitracin: A polypeptide antibiotic isolated from a bacillus (Bacillus subtilis or B. licheniformis) and usually used against gram-positive bacteria.

Back Bacon / Canadian bacon: Bacon cut from the loin that has little fat and is cut into round or oblong slices.

Backward feed evaporator: In this evaporator, fresh feed enters the last and the coldest effect and continues on until the concentrated product leaves the first effect (Plate 83).

What are Genes? Genes are linear sequences of nucleotides of DNA (deoxyribonucleic acid). Each gene consists of a specific sequence of nucleotides and is responsible for determining a particular characteristic of cell. Nucleotides consist of nitrogen –containing compounds called bases, joined to the sugar, deoxyribose and to phosphate. The nucleotide bases are the purines, adenine and guanine and the pyrimidines, thymine and cytosine.

A number of genes are joined together to form a structure called a chromosome.

DNA consists of two strands of nucleotides twisted around each other into a double helical structure. The nucleotide bases are arranged in a specific sequence in each strand. The strand has a backbone of sugar and phosphate from which the bases protrude.

Bacteriophage is the term applied to bacterial viruses. Bacteriophage having the ability to lyse certain sensitive living cells. Phages are small particles, which can only be seen in the electron microscope after the application of suitable staining techniques. All phages have a head and most have a tail. The head may be isometric or prelate with a hexagonal outline.

There are two types of phages virulent and temperate which enter a different relationship with the host, the lytic and lysogenic cycles respectively.

12.1 Bactofugation
Using a specially constructed hermetic centrifuge, the Bactofugation® method separates bacteria—including especially the spores produced by particular bacterial strains—from milk. The RPM rises to 60000. Since their density is larger than that of milk, this technique has shown to be a quick approach of lowering the spore count in milk. Usually separating the milk into a portion more or less free from germs, bactofugation produces a concentrate (bactofugate), containing generally both spores and bacteria in general and amounts to up to 3% of the feed to the Bactofuge.
12.2 Dehydration
One can preserve the milk by dehydrating to different degrees. The “shelflife” of the dehydrated milk is longer than that of milk kept refrigerated and pasteurised. Concentrated or dry milk (milk powder) is milk from which some or all of the water has been removed. More than eighty-percent of milk is water. Eliminating water can help to preserve milks the best way. One can accomplish it freeze drying or by drum or spray drying.
12.2.1 Condensed Milk
Eliminating some of the water from whole or partially/fully skimmed milk, either with or without sugar, results in condensed milk. Generally speaking, “condensed milk” is “full cream sweetened condensed milk,” whereas “evaporated milk” is used for “full cream unsweetened condensed milk.” Variations in skimmed milk are labeled “sweetened condensed skim milk” and “unsweetened condensed skim milk.” For full cream products, milk solids have a concentration ratio of about 1:2.5; for sweetened condensed skim milk, that ratio is 1:3. Annexure-I has an exhaustive composition chart for condensed milk.

Bael (Aegle marmelos, L.) belongs to the family Rutaceae and is an important indigenous fruit of India known since 2000-820 BC. Bael is considered to be native to India and is grown all over the country. It is also seen in south east Asian countries like Sri Lanka, Pakistan, Bangladesh, Burma, Indonesia and Thailand. It is a hardy plant and can be grown even on marginal soils.

The leaves are trifoliate and aromatic. The leaves of the tree are used in religious offerings. The fruit is usually globose, grey or yellowish with small hard aromatic rind. The pulp is thick mucilaginous, orange yellow in colour with sweet scented aroma. The importance of bael fruit lies in its curative properties. It is used in Ayurveda for its medicinal properties.

There are no recognized or improved varieties of bael with a standard name. It usually goes with the name of locality or region it is grown in. Ayodhya, Etawah, Faizabad Local, Gonda Selection, Kagzi Bael, Kagzi Kalan, Mirzapuri, Darogaji, Ojha, Rampuri Azamati, Khamaria, Deoria Large, Gonda-1 and NB-5 are a few to name.

Uses

Bael fruits cut in half, or the soft types broken open, and the pulp, dressed with palm sugar, eaten for breakfast, as is a common practice in Indonesia. The pulp is often processed as nectar or “squash” (diluted nectar). A popular drink (called “sherbet” in India) is made by beating the seeded pulp together with milk and sugar. A beverage is also made by combining bael fruit pulp with that of tamarind. These drinks are consumed perhaps less as food or refreshment than for their medicinal effects.

Mature but still unripe fruits are made into jam, with the addition of citric acid. The pulp is also converted into marmalade or sirup, likewise for both food and therapeutic use, the marmalade being eaten at breakfast by those convalescing from diarrhea and dysentery. A firm jelly is made from the pulp alone, or, better still, combined with guava to modify the astringent flavor. The pulp is also pickled. The young leaves and shoots are eaten as a vegetable in Thailand and used to season food in Indonesia. They are said to reduce the appetite. An infusion of the flowers is a cooling drink. (Morton, 1987).

1. Introduction

Dairy industry size and demand precede all other segments of food industry. Reporting milk production of 146.3 million tonnes in 2014-15, India is currently occupying first position in world scenario (NDDB, 2015). In spite of limited shelf-life, milk offers various opportunities of product diversification, processing optimisation and convenient packaging solutions. All categories of dairy products are unique and vary in market value. The operating margins in value-added dairy products are almost twice of liquid milk business due to reduced need of refrigeration and added shelf-life. The appeal and satiety it offers makes them ambrosia for consumers. Baked and fried dairy products (BFDP) are those class of dairy products in which main processing operation is either baking or frying. In addition to preservation of milk solids for longer time at room temperature, manufacture of baked and fried dairy products add value to milk and also provide considerable employment opportunity (Pal and Raju, 2007;Patil, 2011). The characteristic flavour and colour development of the product rely on this unit operation or cooking method and it cannot be replaced. The unique difference in baked and fried dairy products is that in baking dough is prepared and for frying batter is prepared which vary significantly in characteristics (Table 1). The quality of the finished product greatly depends on how the dough or batter is handled.

Various types of equipment are needed and used to facilitate the process of baking. Depending upon the use, equipment may be as light equipment and heavy equipment.

Baking is no different from any other area of cooking, and as in other sectors only the best and the freshest raw material can guarantee good results. So selection of right kind of ingredients is of utmost importance. Another basic need of a professional baker and confectioner is to purchase the equipment required. The design and size depends upon the volume of sale expected. So in this chapter we are going to learn about the ingredients required for running a bakery.

Formulation & method of bread making Baking is an exact science that requires precise measuring and accuracy. Accuracy is crucial in baking because most baked products are made from the same basic ingredients: flour, liquid, fat, sugar, salt etc. the difference between baked products are often the proportion of each ingredients in the formula. If the proportions are off, you will end up with a different product or an unacceptable product.

1.    Major difference between unleavened and leavened bakery products is

(a) Unleavened do not form cracks on surface

(b) Unleavened do not rise significantly during baking

(c) Leavened bakery products are not attractive

(d) Unleavened products are much more stable

2.    Unleavened bakery products contain small holes throughout the finished product because of

(a) Ingredients contain fats that may swell

(b) Air incorporation between cells

(c) Incomplete coalescence of mixed ingredients

(d) High temperature baking

The word “baked products” refers to a vast variety of foods, such as cakes, bread, cookies, pastries, and crackers, and a variety of other items, and it might be difficult to find a common thread that connects the members of this a varied group. The strongest common connection is that all of them include wheat flour in their recipes.

Banana (Musa sp), is consumed both as a fruit and vegetable. The sweet desert cultivars are generally called bananas and the starchy cooking types are called plantains. It is an important food crop throughout the tropics. References to the banana is frequently made in the Vedic literature, where its use in religious rituals is quite common. Today, it is a leading tropical fruit in the world market with a high degree of export potentiality. Bananas arrives at the world markets the year round. Though India is the largest producer of banana in the world, Ecuador, Hondurus, Columbia, Costa Rica, and Panama are the leading banana exporter, while USA, Japan, Germany, France and UK are the main importing counties.

Banana is believed to have originated in the warm moist tropical regions of SouthEast Asia. Its cultivation is confined to region between 30° N and 30° S of Equator. Banana is grown in many countries namely India, Philippines, Thailand, Uganda, Zaire, Tanzania, Ivory coast, Burundi, Columbia, Brazil, Ecuador, Venezuela, Bangladesh, the Caribbean Islands, the canary Island, USA(Florida), Egypt, Australia, Sri Lanka.

Banana belongs to the family Musaceae and genus Musa. There are several species of Musa which involves both dipoilds and triploids. Most of the cultivated bananas are triploids. They are further classified based on their genomic status. Bananas and plantains are today grown in every humid tropical region and constitute the 4th largest fruit crop of the world, followed by the grape, citrus fruits and the apple.

Varieties/Cultivars: Though there are more than 25 different kinds of bananas grown in India, Grand Naine, Robusta, Poovan, Ney poovan, Rasthali, Karpuravalli, Tellachakrakeli, Red Banana, Nendran, Monthan, Batheesa, Hill Banana (Veerupakshi & Sirumalai) are the popular varieties grown all over the country with different local names.

Introduction

Barley is an important cereal crop grown all over the world and is used mainly for feed and malt purposes and little for human food. Barley is the world’s oldest grain, as evidenced by discoveries in ancient cities in the Middle East and North Africa. It has been cultivated for about 8,000 years, and today is the world’s fourth largest cereal crop. Considerable evidence is available that points to the role of barley as sustaining food source in the evolution of humans. Additionally, alcoholic beverages of various types and fermented foods prepared from barley are commonly referred to in the ancient literature. As other food crops (wheat, rice, corn and rye) became more abundant, barley was relegated to the status of “poor man’s bread”. In the United states, barley used as food is 1.5%, as animal feed 65% and in malt and alcohol production 30% (Newman and Newman, 2006). In 1991, barley used as food in European countries was even lower (0.3%) than the United States. In contrast, during the same time period food was the largest for barley in Morocco (61%), China (62%), India (73%), and Ethiopia (79%). However, current consumer interest in nutrition and human health may help restore barley’s status in the human diet. Nutritional qualities of barley have been known since ancient times. For example, Ajgaonkar 1972 described how ancient Indian physicians effectively stabilized type II diabetics some 2400 years ago. Treatment was remarkable simple and not really different from recommendations that are given to diabetic patients today, i.e., lose weight, change diet, and increase exercise.