eChapters

Physical Chemistry of Foods

    1.    Thermodynamics is primarily concerned with energy and entropy. Energy, also called internal energy (U), comprises heat and work; it is measured in joules (J).

    2.    Energy may be recalled that work generally equals force times distance (in N_·m = J) and that force equals mass times acceleration (in kg ·m· s^-2 = N).

    3.    According to the first law of thermodynamics, the quantity of energy, i.e., heat (q) work (p) potential energy, is always preserved.

    4.    Entropy (S)  is a measure of disorder; it is given by   
        S = K_B ln Ω
        Where K_B is the Boltzmann constant (1.38 ×10^-23 J × K^-1) and W is the number of  ways in which the system can be arranged, also called the number of degrees of freedom.

    5.    Colligative solution properties : The lowering of the chemical potential of a solvent by the presence of a solute causes changes in a number of physical properties: vapor pressure, boiling point, freezing point, osmotic pressure, etc. (the magnitudes of these changes all are proportional to the mole fraction of solute).

Percent Solutions

There are three types of percent solutions. All are parts of solute per 100 total parts of solution. Based on the following definitions you may calculate the concentration of a solution or calculate how to make up a specific concentration

    1.    % W/W - Percent of weight of solute in the total weight of the solution. Percent here is the number of grams of solute in 100 grams of solution. 
        Example: 
        A 100% (W/W) NaCl solution is made by weighing 100 g NaCl and dissolving in 100 g of solution

    2.    % W/V - Percent of weight of solution in the total volume of solution. Percent here is the number of grams of solute in 100 ml of solution. This is probably the least significant way of naming a solution, but the most common way of doing it. In fact, any percent solution not stipulated as W/W, W/V, or V/V is assumed to be % W/V. 
        Example : A 4% (W/V) NaCl solution is 4 g of NaCl in 100 ml of solution.

    3.    % V/V - Percent of volume of solute in the total volume of solution %V/V. Percent here is the number of milliliters of solute in 100 ml of solution. 
        Example: A 10% (V/V) ethanol solution is 10 ml of ethanol in 100 ml of solution; unless otherwise stated, water is the solvent. 

    1.    Absorbance (A) - Defined as –log (1-a) = log (1/t), where ‘a’ is the absorbance and‘t’ the transmittance of a medium through which a light beam passes.

    2.    Absorption coefficient (a) - The relative decrease in the intensity of a collimated beam of electromagnetic radiation, as a result of absorption by a medium, during traversal of an infinitesimal layer of the medium, divided by the length traversed.

    3.    Acceleration due to gravity (g) - The standard value (9.80665 m/s2) of the acceleration experienced by a body in the earth’s gravitational field.

    4.    Acid - Historically, a substance that yields an H+ ion when it dissociates in solution, resulting in a pH< 7. In the Brönsted definition, an acid is a substance that donates a proton in any type of reaction. The most general definition, due to G.N. Lewis, classifies any chemical species capable of accepting an electron pair as an acid.

    5.    Acid dissociation constant (Ka) - The equilibrium constant for the dissociation of an acid HA through the reaction HA + H2O1 A- + H3O+. The quantity pKa = -log Ka is often used to express the acid dissociation constant

    6.    Acyl groups - Groups formed by removing the hydroxy groups from oxoacids that have the general structure RC (=O) (OH) and replacement analogues of such acyl groups.

    7.    Adiabatic process - A thermodynamic process in which no heat enters or leaves the system.

    1.    Nutrients : Chemical substances obtained from food and used in the body to provide energy, structural materials, and regulating agents to support growth, maintenance, and repair of the body’s tissues. Nutrients may also reduce the risks of some diseases.
    2.    Carbohydrate, fat, and protein are sometimes called macronutrients because the body requires them in relatively large amounts (many grams daily). In contrast, vitamins and minerals are micronutrients, required only in small amounts (milligrams or micrograms daily).
    3.    The international unit for measuring food energy is the joule, a measure of work energy. To convert kcalories to kilojoules, multiply by 4.2; to convert kilojoules to kcalories, multiply by 0.24.
    4.    Essential nutrients : Nutrients a person must obtain from food because the body cannot make them for itself in sufficient quantity to meet physiological needs; also called indispensable nutrients. About 40 nutrients are currently known to be essential for human beings. Energy-yielding nutrients: the nutrients that break down to yield energy the body can use:

Abstract

Grains in present context are food grains. The PFA Act includes cereals, millets, and pulses in food grains. At times, seeds of certain oilseeds like soybean are also referred to in the discussion of food grains. Grains have been cultivated for thousands of years. We have Grain Standards as established by the International Organization for Standardization (ISO), which are considered as International Standards. Another source is Codex Alimentarius Commission (Codex) under the aegis of FAO (UN), which operates a Committee to formulate standards that are referred to as Codex Standards. Many countries have a National Standards Institution, which develops National Standards for their main grain crops and other commodities and issues specifications along with methods of testing and analysis. Several countries, which are in developing status, adopt or modify international standards into their national system. The Grain Standards have been evolved and established for a variety of purposes but primarily to grade produce in agricultural marketing largely to facilitate the movement of grain, provide both sellers and buyers with guidelines to support financial transactions, and ensure that the produce will meet up with end-use requirements, or, increasingly to protect the consumers.

Abstract

A survey of various wheat milling units (atta chakki) available around Indian Agricultural Research Institute, New Delhi was conducted to study the performance of these. The mills of various sizes (12", 16", 18", 20", 24" and 30" stone disc diameter) with horsepower ranging between 2 to 20 are in operation. Both horizontal and vertical disc types of mills are in use. The capacity of these units ranges between 10 kg/h to 200 kg/h. The stationary sieve, hand sieve, pedestal/exhaust fan are used for cleaning. The average wheat cleaning cost is Rs. 200 per ton. A small room of 8' x 10', 10' x 10' and 10' x 12' size is used for running the mills and storage of wheat grains. The grinding charges (Rs./q) of wheat, coarse grains (maize, sorghum, millet etc) and spices are 100, 200 and 1000, respectively. Sample of 500 g of wheat and flour were collected from each chakki and were analysed for wheat grain and flour quality. Infested, damaged grains were observed to be in 2-10% range. Sieve analysis of the flour was done and the average particle size, fineness modulus and uniformity index of the flour were calculated. Average particle size, fineness modulus and uniformity index were found in the range 0.1875 to 0.2023 mm, 1.052 to 1.297 and 0:1:9, respectively. Average particle size of the flour obtained from horizontal mills was found to be higher than vertical mills. Temperature of the flour at the outlet was observed in between 45 and 50°C at room temperature of 18.5°C.

Abstract

There is an urgent need to – create market driven linkages rather than do it alone by building new infrastructure. A lot needs to be done to improve infrastructure in terms of reducing the logistics cost, eliminating middlemen influence and eliminating the wastage of basic inputs. There is a need to blend technologies based on principle of dovetailing production for masses with the advantage of mass production, particularly in the area of grain processing, packaging and marketing which would help combine livelihood, security with agricultural competitiveness. Risk in crop production is not new to any age and the farmers have been bearing it since times immemorial. The farmers should be allowed to maximize their grain. High performance continuous and batch dryers remove moisture in a way that is predictable and reliable. The problems associated with moisture content may be harmful to international trade in grain and need to be addressed adequately by the standardization institutions.

Abstracts

About 60-70% of total food grain production is retained and stored by farmers for household consumption, use as seed, feed for cattle and payment of wages to labours etc. in our country. Yet the quality of grains stored is not so good, and hence, preserving the harvested crops without loss or damage has always been a problem of national importance. This study was conducted in Jabalpur district of Madhya Pradesh state. A tribal block namely Kundam was selected for study purpose. The responses of 120 women were recorded in pre-tested structural schedule through interview. Rural women are an important source of information on the use of indigenous practices for grain storage. The data reveals that the majority of respondents are using dry leaves of Neem, dry onion bulb, wheat straw, Nirgudi leaves, roots of bach etc. for storage of grain at household level. In our country, indigenous practices of grain storage have always been and are still followed, because it is supposed that these practices are useful in control of grain loss.

Abstract

Pulses constitute an important component of the diet and are a major source of protein in vegetarian diet. India has largest area under pulse cultivation and produces a variety of pulses. A large portion of this produce gets spoiled due to insect and fungal attack. A variety of insecticides and fungicides are used for the control of pest during storage. There is an increasing trend towards the reduction in the use of pesticides in storage due to strong demand from consumers to choose food with no pesticide residue, development of insect resistance to pesticides and the impact of pesticides’ use on environment. All these have posed a challenge to refine the existing management procedures of storage and commodity to find the optimal solution. Controlled/ Modified Atmosphere storage offers an alternative to the use of pesticides extends storage life and maintains product quality. The Controlled/Modified Atmosphere is created by altering the composition of the atmosphere in terms of CO2, O2, and N2 concentration. High CO2 produce undesirable conditions for insects and microbes and thus control their activity.

Abstract

Maintaining grain in good condition in storage requires careful, routine inspection and good storage practices. An integrated approach of several management tools and practice factors are necessary to manage stored grain to prevent deterioration and wastage: This includes:1) harvesting, handling, and storage equipment; 2) initial condition of the grain; 3) grain moisture content; 4) grain temperature; 5) aeration system management ; 6) insect and mold control; and 7) monitoring grain condition. An effective management program greatly enhances the likelihood of maintaining top quality grain. A well- designed and properly operated storage system with adequate aeration capacity, storing only clean grain at the proper moisture content and temperature, sanitizing the bin before loading, checking the grain condition regularly and correcting problems before they get out of hand are critical management strategies that must be implemented to prevent grain damage and possible serious economic loss.

Abstract

The demand for the food for ever increasing population is always continuous, but the production is limited to specific seasons. Therefore the food grains have to be stored for sometimes. Grain is a living biological material and therefore storage structures should be suitably designed to protect them from the ravages of pests, rodents and micro-organisms. However, the storage losses account for a major portion which can be reduced to considerable extent if proper care is done. The faulty design, poor maintenance and limited knowledge of the farmers concerning storage technology have greatly added to the spoilage of the food grains during storage. Sometimes the foods if not properly stored may be edible but it may lose the essential vitamins and minerals, thus their nutritive value has been lost. There is a major requirement of a good storage structure. Various food grain storage structures (small and large scale) are described.

Abstract

Three-point bend test (three point bend ring-HDP/3PB) for five types (Good day, Butter bite, Marie, Krack Jack and Salted) of commercial biscuit brands (Britannia, Supreme, Parle, Lancer, Priya Gold and Dalmia) was developed using TA-XT2, texture analyzer and probable factors affecting the results were assessed. Maximum force to break the biscuits, number of fracture before break, thickness of biscuits and percent break point penetration were found in the range of 1006.5 to 3456.5g, up to 3, 4.2 to 6.3mm and 5.54 to 22.62%. The rupture of biscuits were observed on the basis of probe penetration into the biscuits and found that maximum resistance for penetration offered by Marie whereas minimum by salted biscuits, which was respectively the hard dough and fermented dough biscuit varieties. The analysis of variance for the results revealed that there is significant difference (P£0.01) in the maximum force of break for the biscuit types and brands individually or in combination. Difference in the thickness of biscuits was also found significant among types and commercial brands. The number of fractures was not consistent among the types as well as biscuit brands before reaching the maximum force of breaking the biscuit.

Abstract
 
Technological advancement, increased urbanization, awareness and interest of consumer for variety products have given a great challenge to the food sector to develop inexpensive foods that are nutritionally superior and acceptable to the intended consumers. Keeping this objective in view, we have made an attempt to develop technology for variety products from wheat and corn and suitability of available varieties judged. With the emerging trends of food market towards fast foods, there are vast prospects for efficient utilization of cereals by exploring varieties products. A steamed bread (a Chinese traditional product) and Tortilla and corn chips (Mexican snacks) were developed. Steamed bread is defined as the product resulting from cooking or steaming fermented dough. Recipe and method for its preparation was standardized. Nutritionally rich steamed bread can be prepared by supplementing 10% level of chickpea and defatted soybean flour. Corn snacks have become a prime target of some consumer advocates and nutritionists who have referred them as a source of ‘empty calories’. But reality is that these snacks provide instant energy, as they are rich storehouse of nutrients. Process and recipe for the preparation of Tortilla and corn chips from Indian maize were standardized. The quality and acceptability of these snacks were worked out and found that these products were highly acceptable. Indian consumers have versatile taste, so these products will be readily accepted in Indian market. 

Abstract

Four bread wheat varieties (PBW-138, PBW-299, PBW-343 and PBW-373), two of durum wheat (PDW-215 and PDW-233) and two of triticale (TL-419 and TL-1210) were milled to obtain 70 percent extraction flour.  The grains and the flour samples of all the varieties were evaluated for proximate composition, rheological properties and pretzel making. Physical properties of durum wheat were better followed by bread wheat and triticale. Durum wheat were harder, had higher grain weight than bread wheat and triticale.  Protein, ash, fat, total sugars and enzyme activity were higher in triticale flour than bread and durum wheat flours while durum flour had higher pigments (ppm, b-carotene). Bread wheat flour was intermediate between durum and triticale flours with respect to fineness. Rheological studies revealed triticale flour to be the weakest flour. Pretzels prepared by using optimized recipe and method revealed PBW-343 and PBW-373 best for pretzel making.

Abstract

The establishment of All-India Coordinated Wheat Improvement Project in 1965 coincided with the introduction of high yielding semi-dwarf wheat varieties. Since then India has made very impressive progress in increasing wheat production over the past three and half decades. India now ranks as the second largest wheat-producing nation in the world. In fact from a state of “Ship to mouth” in 30 years or so India has become a nation of surpluses. The significant contribution made by the project in helping the increased wheat production cannot be ignored. Through coordinated research and development, nearly 200 wheat varieties have been developed during the last 35 years in India. However, only a small number of them produced without backing of specific quality breeding programs excel in quality traits also. The increasing demand of baked and pasta products in the country along with economic liberalization and global trade have offered opportunities for better utilization of the surplus wheat. Thus, in the current decade and beyond, wheat quality needs uppermost attention to meet the trade requirements for domestic and export purposes. Therefore, there is a need to reorient the wheat improvement programs in the country.

Abstract

Sunflower seeds of variety PSFH- 67 were obtained from the PAU seed farm. These seeds were cleaned with commonly used seed processing equipment. Samples were divided into 2 parts. One part was kept as such for taking the observations of feed (control) and the remaining part was passed through specific gravity separator for its refinement. The various fractions obtained were recovery (heavier, healthy seeds), middlings (intermediate, under size) and rejections (lightweight seeds, wevil eaten, foreign matter). The respective percentages of each fraction were computed. These graded fractions as well as the feed were packed in 2-kg cloth bags and stored under ambient conditions. Different quality parameters viz. moisture content, physical purity, percent germination, thousand grain weight and vigour index were recorded at 30 days interval from Jan, 2010 to Apr. 2010. The physical purity, moisture content, thousand grain weight, percent germination, root length, shoot length and vigour index were found to be higher in recovery and minimum for rejections while moisture content was highest for rejection compared to all other fractions. The physical purity remained more or less constant throughout the period of storage. The thousand-grain weight showed a rapid decrease during first month thereafter it remained constant. There was continuous decrease in percent germination with the period of storage irrespective of the treatment.

Abstract

High moisture paddy can be dried in a trolley drier at farm level/grain market to reduce losses during various post harvest operations. During last two paddy harvesting seasons quality analysis of eight, most popular varieties of fresh paddy arrivals from about 40 grain markets, scattered all over Punjab, was performed. Monitoring of paddy in grain markets showed that maximum number of samples (62.7%) was in the range of 12-18%, moisture content (w.b.). Over-dried paddy samples (<12% m.c., w.b.) were only 9.1%. The samples with more than 18% m.c ,w.b. (high moisture paddy) were 28.2%, which have to be dried to safe moisture levels. Milling characteristics of the analyzed samples indicated that the broken percentage was highest (25.5%) in PR-113 followed by PR-111 (20.6%) and minimum in Pusa-44 (12%). The highest insect- pest infestation (Sitotroga cerealella (olivier) was observed in PR-108, followed by PR-116, PR-113, PR-111, Lal Mundi, Govinda, PR-114 and Sharbati. The Mycoflora isolated and identified were Aspergillus, Penicillium, Mucor, Rhizopus, Alternaria, Curvularia, Helminthosporium and Cladosporium spp. Maximum fungal infestation were associated with samples of PR-108 variety. To avoid further proliferation of mycoflora and inset pests, paddy should be dried to safe moisture levels for further storage and processing. For this, a trolley drier has been developed by converting a conventional farmer’s tractor trolley, into a portable drier, which can reduce 5% moisture of 1 tonne batch of paddy in about 100 minutes, consuming 56 kWh of electrical energy

Abstract

‘Made in India’ is no more a sign of poor quality. However, in the field of food grain exports, India is still lacking the required determination. The Indian food grains get rejected in the International market because of its out-dated post harvest technology (PHT). The Food Corporation of India (FCI) is the nodal national agency for the procurement, storage, processing and transporting of food grains, and their further distribution through the Public Distribution System (PDS). The government fixes the procurement price as well as the distribution price of the food grains, and the FCI has to accept it. The government compensates the resulting loss through subsidy. The government, through FCI, must encourage cultivation and marketing of premium quality food grains, by offering suitable incentives to farmers. The cost of marketing, storage and transporting of food grains can be considerably reduced with simultaneous improvement in quality of the end product, if the prevailing bag handling is replaced by bulk handling, storage, and transportation. However this needs closer coordination between various departments of the Ministry of Food and Ministry of Railways. The President of India revealed his vision to make India a developed country by the year 2020. To achieve this, the current post harvest losses to the tune of 10 percent must be reduced to 2 percent. This is possible if the government takes bold political decision supported by equally firm and time-bound necessary

Abstract

India has become not only self sufficient in food grains but has also emerged as net exporter of wheat and rice. Acute famines in India have practically been eliminated, thanks to increased food availability at the national level, improved early warning systems and expanding infrastructure for more rapid transport of food grains and other products to needy areas. However, the existing post management system, strategies and policies don’t seem to match new challenges. Despite government intervention in pricing and procurement of food grains, primarily wheat and paddy, India continues to suffer heavily on account of losses and wastages incurred during the post harvest stages, which are more manmade than natural. Some losses have already occurred before the arrival of food grains in the regulated and wholesale markets and continue till food grains reach their destination. What contribute to continuing losses and wastages are improper post harvest handling, government policies and their implementation, which even stifle growth and modernisation of grain markets and processors.

Abstract

Garden peas of two cultivars (Pb-87 and Pb-88) were procured. Pods were shelled manually, grains were blanched and dehydrated. Other lot of peas of both the varieties was allowed to mature on the plant till the plant foliage dried up, harvested, pods were dried in shade for few days, shelled manually and grains were further dried in shade. Grits were prepared by grinding rice and pea (dhal) in a laboratory grinder to pass through 20 mesh sieve. Blends were prepared by mixing rice and pea grits in the ratio of 100:0, 85:15 and 70:30. The blends were subjected to extrusion cooking using Brabender single screw extruder. The extruder die pressure, specific energy consumption (SEC), expansion ratio, density, water absorption index (WAI), water solubility index (WSI) and organoleptic characteristics were studied. Addition of pea grits resulted in a decrease in die pressure in all the blends. Addition of pea grits showed a significant effect on SEC. A decrease in expansion with increase in the level of pea grits in blend was observed. The extrudates having lower expansion showed higher density values and vice versa. Effect of replacement of rice grits with pea grits on WAI was found to be significant. Level of pea grits significantly affected the WSI. Incorporation of pea grits in the rice grits significantly affected the sensory characteristics. Replacement of rice grits with mechanically dried pea grits resulted in deterioration of acceptability score, but addition of field dried pea grits improved the same.

Abstract

Paddy seeds of variety PR - 116 were obtained from the PAU seed farm. These seeds were cleaned with commonly used seed processing equipment. Samples were divided into 2 parts. One part was kept as such for taking the observations of feed (control) and the remaining part was passed through specific gravity separator for its refinement. The various fractions obtained were recovery, middlings, and rejections. These graded fractions as well as the feed were packed in 5-kg cloth bags and stored under ambient conditions. Different quality parameters viz. moisture content, physical purity, thousand grain weight, percent germination, root/shoot length, vigour index and speed of germination were recorded at 30 days interval. The physical purity, thousand grain weight, percent germination, root length, shoot length and vigour index were found to be higher in recovery and minimum for rejections while moisture content was highest for rejection as compared to all other fractions. Germination, root/ shoot length, vigour index and speed of germination increased with the duration of storage while moisture content, thousand-grain weight and physical purity followed a reversed trend. Compared to feed, the recovery had higher quality attributes after 4 months of storage viz. moisture content decreased by 0.3%; physical purity increased by 0.67%; thousand grain weight increased by 2.97 gm/ thousand grain, germination increased by 8%; vigour index increased by 481.1 points; speed of germination increased by 3.2 seedlings per day. The grading resulted in improvement in overall quality of sunflower seed.

Abstract

30 lines were selected from 864 germplasm lines for good biscuit making attributes on the basis of low protein content (<10.5%) and low sedimentation value (<40cc). These lines were further screened by actual baking test and alkaline water retention capacity (AWRC) test keeping the standard prescribed for biscuit making qualities viz., low protein content, low sedimentation value, low AWRC and larger diameter with larger spread ratio of biscuit. AWRC had significant negative correlation with biscuit spread ratio. Positive significant correlation was found between biscuit spread ratio and biscuit diameter. On the basis of above findings, it may be recommended that low protein content, low sedimentation value, low AWRC may be used as criteria for better biscuit making i.e. increase biscuit spread ratio and biscuit diameter. So wheat-breeding programme has opened up new opportunities for the end use quality product and wheat based food industry. Hence there is an urgent need for qualitative analysis of desired traits in wheat towards enhanced value addition and thereby an attempted has been made to identify suitable genotypes possessing good biscuit making attributes

Abstract

The control of micronutrient deficiency is a realizable goal, notwithstanding the magnitude of the task, challenges and constraints that need to be resolved. Since wheat products particularly maida and atta form the major raw material in widely consumed food items like chapati, bread and biscuit. Fortification of flour as followed in many other countries could be an important strategy to help realize this goal. The technology of flour fortification is effective and cost affordable. Effective flour fortification program would require collaboration between scientific community, governmental and non-governmental agencies, and industry and consumer groups.

Abstract

The constant improvement in automation of bakery industry has placed higher demands on wheat. As a consequence bakery industry requires wheat possessing specific quality attributes. In view of this, there is need to produce good quality wheat not only for good chapattis but also for better bakery products viz., bread, biscuit, noodles, pasta products. New technologies are emerging which could be exploited for determining the Indian wheats for their suitability for various value added products. In the current investigation, 50 genotypes possessing low protein content (<10.5%) selected from a vast amount of breeding material were analysed for their biscuit making attributes. These lines were screened by actual baking test and alkaline water retention capacity (AWRC) test keeping the standard prescribed for biscuit making qualities viz., low protein content, low sedimentation value, low AWRC and larger diameter with larger spread factor of biscuit. Further with the help of Stable Micro Systems TA.HDi Texture Analyser the biscuits were analysed for hardness and crispness. Correlation coefficient among 8 quality traits suggested highly significant and positive correlation between sedimentation value and AWRC, biscuit diameter and spread factor, and biscuit hardness and fracturability, and significant negative correlation between biscuit diameter and its thickness. On the basis of findings, genotypes identified for biscuit making qualities may be used as donor for developing varieties suitable for biscuit making.

Abstract

Pulses being nutritionally vital, is an important constituent of diet for a very large number of peoples. A part from being a relatively cheaper source of dietary protein, it is also an important source of calories, certain essential amino acid, minerals and vitamins. Post harvest scenario of pulse shows that 75 per cent of production was milled in pulses with as dehusked split i.e. dal. Traditionally green gram and black gram dal is dehulled manually after soaking in water. Present investigation was carried out to develop the wet type dehuller and study was carried out on water absorption characteristics of green gram and black gram. The result reveals that the dehulling efficiency of abrasion type mechanism was about 95 per cent and 92 per cent in case of shearing type mechanism. It has been observed that rate of water absorption was initially high and then gradually decreases i.e. 0.54 to 0.18 and 0.48 to 0.18 for black and green gram, respectively. 

Abstract

Consumers are now more conscious about quality and source of their foods. Attempts made to determine the quality of food materials are numerous, but most of them are destructive in nature. In recent years, nondestructive methods of quality evaluation have gained momentum and a considerable attempts have been made to develop them. This paper describes application of these non-emerging technologies: magnetic resonance imaging, x-ray computer tomography, near infrared spectroscopy and a few other important techniques for determination of different quality attributes with special emphasis on grain, and discusses their pros and cons for practical exploitation.

Abstract

Wheat gluten consists mainly of gliadin and glutenin polypeptides. During mixing gliadin and glutenin proteins interact to form a unique viscoelastic gluten network, which is envisaged as being necessary for holding the gases and for producing a light porous crumb textured bread. Recent work has confirmed that the elastic properties of gluten are due to the glutenin fraction, whilst the viscous properties are attributed to the gliadin fraction. Equal amount of these two major protein components of wheat gluten is required for achieving the desired bread quality, but variation in the composition and physical properties of the glutenin polypeptides appear to be largely responsible for the differences in the gluten viscoelasticity and breadmaking potential among wheat cultivars. Recently, associations of gliadin polypeptides with breadmaking quality have also been reported. Using improved protein separation and purification techniques, physical methods and genetic engineering, we are beginning to understand the structure-functional relationship of wheat gluten proteins, but much remains to be explored in the years to come. 

Abstract

Determination of quality of wheat is very important because quality requirement of an individual product vary from one another. Flour quality can be defined as the ability of the flour to produce a uniformly good end product. Flour quality factors can be divided into two basic groups: those that are inherent in the wheat as a result of the genetic make up and the changes brought about by growing conditions; secondly those factors that might be altered during the process of converting wheat into flour Wheat flour constituents play an important role in determining the quality of flour. The flour quality for baking could be assessed by measuring the physical, chemical and rheological characteristics.

Abstract

Adulteration refers to a process by which the quality or the nature of the given substance is reduced by the addition of foreign or an inferior substance, removal of vital component, packing and storage under harmful conditions, insect infestation, poisonous material, undesirable chemicals and unintentional contaminants. All these change in food whether intentional or unintentional are covered under food adulteration. In cereal grains adulteration results by incidental contamination during the period of growth, harvesting, processing, transport, and distribution and results in various health hazard, sand, marble chips, earth and filth are also adulterants in grains. Pest and pesticides residues are also hazardous.

Abstract

Majority of basic research in our country has foundations in Universities and various Institutions linked to them. This paves way for discovering wilder varieties of the present known cereals and other food crops. Such findings help in bioprospecting the required gene/genetic material for the improvement of the existing crops. As per the Biodiversity Act of 2002, it is the responsibility of these institutions to document the same. But, as research scientists are geared to meet the challenges? Being used to socialistic system from the days of Independence where knowledge generated was open to everyone or closed and kept under the mountains of files, the TRIPS agreement has come as a shock. But the true impact of it was realized in 1999-2000, when the patent amendments were taken up. The private institution/ companies went into the act immediately.  We in the University neither were slow to react nor were we prepared to take the shock.  In this paper some of the problems pertaining to IPR and scenario of Indian Universities and Institutions in this regard were highlighted.

Abstract

Mycotoxins are naturally occurring chemicals produced by fungi growing on grain, feed or food. The fungi that produce mycotoxins in grains commonly include Fusarium, Aspergillus and Penicillium species. The toxins can accumulate in maturing corns, cereals, soybeans, sorghum, peanuts and other food and feed crops in the field and in grain during transportation. The toxins may occur in storage under conditions favorable for the growth of the toxin producing fungi. Diseases in animals and human beings resulting from the consumption of mycotoxins are called Mycotoxicoses. These fungal metabolites are detrimental to the health of both animals and human. Toxicity ranges from acute death to chronic diseases, cancer and reproductive malfunction. Mycotoxin contamination of food and feed grains is a serious economic problem for grain producers and processors because grain contamination impacts market 

Abstract

There are enormous food processing industries comprising of grains and oilseeds milling, fruits and vegetables processing, spice grinding and other food processing units in India. Also, there are many seed processing companies in the country, which are engaged in the processing and production of good quality seeds of different crops besides National Seeds Corporation and State Seed Corporations. All industries are using different type of machinery and equipment like cleaner, grader, expeller, milling machines, polishers, dehusking machines, size reduction equipment, different type of grinders, separators, treatment machinery, mixers, pulverizes etc. Besides this equipment, material-handling equipment like conveyor (belt, chain or screw type), elevators, holding bins and other handling equipment are also frequently used in the processing plants. To meet the above requirement many firms are also involved in the manufacturing of these equipment and machinery. Since, most of the seed processing equipment, dhal milling plants, material handling equipment are manufactured by the unorganized sector and hence equipment and machinery fabricated by them are not of very good quality. However, Bureau of Indian Standards has formulated the codes of manufacturing for these equipment and machinery. Seed processing equipment manufactured in India are generally copy of imported processing equipment. The manufacturers do not use materials of good quality. Framework of the machines is very poor. These machines are not also tested for their efficiency, 

Abstract

Wheat is unique among cereals because of its ability to form viscoelastic dough. Variety of products such as leavened and unleavened breads, pasta, cookies, and breakfast cereals are prepared using wheat. The viscoelastic property of dough is mainly due to the presence of gluten proteins viz., gliadins and glutenins. Variations among these proteins play a significant role in determining the quality of wheat. Although considerable studies have been carried out on quantity and quality of protein and their relation to bread quality, very little work has been reported on their relation with quality of Indian traditional products like chapati and tandoori roti. Results indicate that ratio between gliadins and glutenins are important in determining the chapati quality. It has been found that varieties having 5+10 HMW glutenin subunits with IBL/ IRS chromosomes are more suitable for the preparation of chapati and roti. This article is focused on the relation between protein and its subunit composition and the quality of chapatti and roti quality.

Abstract
 
The definition of quality is described from a very simpler one “fitness for purpose or use” to a comprehensive “the totality of features and characteristics of a product or service that bear on its ability to satisfy stated or implied needs”. The concept of total quality management in food industry is adopted recently and it is the “integrated organization approach in delighting customer (both external and internal) by meeting their expectations on a continuous basis through everyone involved with the organization working on continuous improvement in all products/processes along with proper problem solving methodology”. TQM is concerned with the integration of all the efforts in organization towards quality improvement, quality development and quality maintenance to meet full customer satisfaction at economic levels. TQM enhances the work culture and employee’s satisfaction through participation and involvement and consequently the image of the organization.

In most countries there is no legislative definition of the term drawing a border line between conventional and functional foods is challenging even for nutrition and food experts. Functional foods do not have a specific place in food law; consequently there is a great deal of confusion about what they are, could or should be. A common perception is that functional foods are foodstuffs either with one or more specific added ingredients (components), or certain substances of common ingredients (components) removed and which are claimed to have a positive influence on human health or well being. The term ‘functional foods’ for this group of products is considered to be an unfortunate one since all foodstuffs are or should be functional and a more appropriate term might be helpful.

Introduction
 
The future of functional foods is bright and there are several reasons for the growing interest in “functional” foods, such as awareness of personal health deterioration, led by busy lifestyles with poor choices of convenience foods and insufficient exercise; increased incidence of self-medication; increased level of information from health authorities and media on nutrition and the link between diet and health; scientific developments in nutrition research; and a crowded and competitive food market, characterized by pressurized margins. Now, the consumer is well aware of the relationship between diet and health. Consumers understand that the risk for chronic diseases such as heart disease, stroke, colon cancer, and type II diabetes is possibly preventable by modification in their diet pattern. This scientific progress in understanding the relationship of diet to disease, along with increasing health care costs and the consumer’s desire to initiate healthy eating and lifestyle habits, makes this a potentially fertile ground for the development of food products that meet these demands.

Introduction

The search for weight controlling foods began in the mid 19^th century when industrialization led to widespread obesity. Over the years, people have tried to lose weight by avoiding particular food groups like carbohydrates, eating specific foods such as cabbage soup, or adding a certain ingredient, like vinegar or grapefruit to each meal. Recently scientists have demonstrated that green tea, dairy products, and cinnamon have the potential to improve weight control by altering fat and/or carbohydrate metabolism at the sub-cellular level. Considerable research is needed, however, before these food items can be used to develop effective weight management products.

Introduction
 
Diabetes shows a wide range of variation in prevalence around the world and it is expected to affect 300 million by the year 2025. In a prevention framework where banning policies and educational strategies lead the interventions, functional foods (FFs) with their specific health effects could, in the future, indicate a new mode of thinking about the relationships between food and health in everyday life. Functional ingredients, such as stevioside, cinnamon, bitter melon, garlic and onion, ginseng, Gymnema sylvestre and fenugreek, have been addressed for their specific actions towards different reactions involved in diabetes development. New strategies involving the use of FF should be validated through large scale population trials, considering validated surrogate end points to evaluate the effect of FF in prevention of chronic diseases such as type 2 diabetes mellitus.

Introduction
 
Cardiovascular disease (CVD) is still a major cause of death in Western populations and is becoming an important cause of morbidity and mortality worldwide. Thanks to advanced medical knowledge and treatments, many patients survive an initial event. Because of that, prevention of secondary CVD is a growing task for nutritionists and other health professionals. Cardiovascular risk can be reduced by lifestyle changes, one of which is diet. There is now substantial evidence from epidemiological and clinical studies that a diet rich in fruits, vegetables, unrefined grains, fish and low-fat dairy products, and low in saturated fats and sodium, can reduce the risk of coronary heart disease and hypertension.

Introduction
 
Developments in innovative food packaging technologies have evolved in response to the need for protection of the food product containing bioactive component from both external and internal environments and in response to consumer expectations for health claims, convenience and product safety. Consumers around the world are willing to pay extra for guaranteed product freshness delivered by the type of packaging. Many new packaging developments have focused on extending the shelf life of the product and on delivering a higher quality product to the consumer. These developments would not be possible without significant advances in the materials used in packaging and the incorporation of various types of sensors into food packaging. This chapter outlines the innovative packaing solutions in the production of functional food.

Introduction
 
The emerging functional foods market presents a considerable challenge to all manufacturers to keep abreast of the use of adequate packaging materials for their products. The interest in functional foods is intrinsically linked to the potential health benefits of their bioactive components. Preserving these bioactive components is, therefore, a crucial factor to providing the anticipated health benefits of functional foods. However, recurring failure in maintaining the quality of functional foods has been reported. Functional foods include a wide variety of products such as prebiotics and probiotics, dried foods (fibers, probiotics, tea, herbs, etc.), fermented products (yogurts, kefirs, vegetables), and fresh fruits and vegetables.

Introduction

The emerging functional foods market presents a considerable challenge to all manufacturers to keep abreast of the use of adequate packaging materials for their products. The interest in functional foods is intrinsically linked to the potential health benefits of their bioactive components. Preserving these bioactive components is, therefore, a crucial factor to providing the anticipated health benefits of functional foods. However, recurring failure in maintaining the quality of functional foods has been reported. Functional foods include a wide variety of products such as prebiotics and probiotics, dried foods (fibers, tea, herbs, etc.), fermented products (yogurts, kefirs, vegetables), and fresh fruits and vegetables. Their bioactive components (minerals, vitamins, fibers, peptides, proteins, w–3 polyunsaturated fats, antioxidants, enzymes, and symbiotics) range from very simple molecules to complex living organisms such as bacteria.

Introduction

Since 1990, there has been a lot of interest in functional foods and nutraceuticals, particularly because of their impact effects on human health and the prevention of certain diseases. Apart from growing good quality natural products, there are challenges in extracting, refining, analyzing active ingredients, and evaluating safety before an effective, reliable product is made [1,2]. Special attention needs to be focused on separation and purification mainly because 40-80% of the cost of production is assigned to separation and purification unit operations in making functional foods and nutraceuticals. There are also several carotenoids and polyphenol products that have been identified from various plants and a single plant could contain highly complex profiles of these compounds. These are labile to heat, air, and light, and they may exist at low concentrations in the plants. This makes the separation and detection of nutraceuticals a challenging task. The membrane techniques used for the separation of nutraceuticals from the natural products, as well as their applications and influencing factors are discussed in this chapter [3, 4].

Introduction

Spray drying process has been used for decades to encapsulate food ingredients such as flavors, lipids, and carotenoids. During this drying process, the evaporation of solvent, that is most often water, is rapid and the entrapment of the interest compound occurs quasi-instantaneously. This required property imposes a strict screening of the encapsulating materials to be used in addition to an optimization of the operating conditions. Likewise, if the encapsulated compound is of hydrophobic nature, the stability of the feed emulsion before drying should also be considered.

Introduction
 
In recent years, there has been a growing interest in the functional foods because they can provide physiological benefits additional to nutritional and energetic, as for instance, antihypertensive, antioxidant or anti-inflammatory [1]. A functional food can be defined as a food that produces a beneficial effect in one or more physiological functions, increases the welfare and/or decreases the risk of suffering a particular disease. Furthermore, new types of products, derived from food, called nutraceuticals have recently been developed. These products, usually employed as food supplements, are marketed as tablets and pills, and can provide important health benefits.

Introduction

Encapsulation may be defined as a process to entrap one substance (active agent) within another substance (wall material). The encapsulated substance, except active agent, can be called the core, fill, active, internal or payload phase. The substance that is encapsulating is often called the coating, membrane, shell, capsule, carrier material, external phase, or matrix. In the food industry, encapsulation process can be applied for a variety of reasons. Encapsulation is a useful tool to improve delivery of bioactive molecules (e.g. antioxidants, minerals, vitamins, phytosterols, lutein, fatty acids, lycopene) and living cells  (e.g. probiotics) into foods [1]. In most cases, encapsulation refers to a technology in which the bioactive components are completely enveloped, covered and protected by a physical barrier, without any protrusion of the bioactive components. Also, encapsulation has been defined as a technology of packaging solids, liquids, or gaseous materials in small capsules that release their contents at controlled rates over prolonged periods and under specific conditions. Produced particles usually have diameters of a few nm to a few mm.

Introduction

Spices and aromatic herbs have been used since antiquity as preservatives, colorants, and flavour enhancers. Spices, which have long been the basis of traditional medicine in many countries, have also been the subject of study, particularly by the chemical, pharmaceutical, and food industries, because of their potential use for improving health. Both in-vitro and in-vivo studies have demonstrated how these substances act as antioxidants, digestive stimulants, and hypolipidemics and show antibacterial, anti-inflammatory, antiviral, and anti-carcenogenic activities. These beneficial physiological effects may also have possible preventative applications in a variety of pathologies. The chapter presents an overview of the potential of spices and aromatic herbs as functional foods ingredients.

Introduction
 
Whilst food has long been used to improve health, our knowledge of the relationship between food components and health is now being used to improve food. Although most foods can be considered “functional”, in the context of this review, the term is reserved for foods and food components that have been demonstrated to provide specific health benefits beyond basic nutrition. Widespread interest in select foods that might promote health has resulted in the use of the term “functional foods”. Seaweeds are known for their richness in polysaccharides, minerals and certain vitamins [1], but they also contain bioactive substances like polysaccharides, proteins, lipids and polyphenols, with antibacterial, antiviral and antifungal, as well as many such other properties [2]. This gives seaweed great potential as a supplement in functional food or for the extraction of compounds. Physiologically active substances in marine algae are classified into two types based on the difference in the mechanisms viz. (i) non-absorbed high-molecular materials like dietary fibres, and (ii) low molecular materials, which are absorbed and which affect the maintenance of human homeostasis directly. Seaweeds are among the first marine organisms chemically analyzed, with more than 3,600 articles published describing 3,300 secondary metabolites from marine plants and algae, and they still remain an almost endless source of new bioactive compounds [3].

Introduction

The term probiotic is derived from Greek and means ‘for life’ as opposed to antibiotics which means ‘against life’. The history of probiotics began with the consumption of fermented foods which was first observed in ancient Greeks and Romans [1]. The term, probiotic, as is used today was first used by Parker in 1974. Parker defined ‘probiotic’ as substances and organisms which contribute to intestinal microbial balance. In 1989, the term was modified further by Fuller. Thus, probiotic is a live microbial supplement which affects the host’s health positively by improving its intestinal microbial balance. This definition was broadened to include mono or mixed culture of live microorganisms which benefits animals or man by improving the properties of the indigenous microflora [2]. Some authors have interpreted probiotics as microbial cell preparations or components of microbial cells that have a beneficial effect on the health and well-being of the host.

Introduction
 
Dairy ingredients are of significant importance in the formulation of many food products. Additionally, the incorporation of dairy ingredients, comprehensively recognized by the consumer as “natural” intensifies the odds of success of packaged foods and adds functional properties of the dairy ingredients in the targeted product. Dairy ingredients can be extracted from fluid milk in the form of cream, butter, condensed milk, dry milk, cheese, and whey products [1]. They provide beneficial functionality to foods, such as delivery of key nutrients, water management, fat-holding capacity, emulsification capability, viscosity creation, gel formation, and foam generation apart from providing desirable attributes of texture and flavour. Various ingredients and claims associated with dairy foods are shown in Table 3.1.