eChapters

About 80% of the world population live in developing countries and are dependent on agriculture. Agricultural products, just after harvesting, are dried to the safe moisture level. Open solar drying for drying agricultural products is being practiced since ages throughout the world. Due to its several drawbacks as danger of (dust, rain, ultra-violet rays, birds, animals etc.), advance technique, i.e. greenhouse drying, is being adopted for drying crops to reduce the drying time and increase the quality of the food products.

Drying involves a heat and mass transfer phenomenon in which heat energy supplied to the product surface is utilized in two ways: (i) to increase the product surface temperature in the form of sensible heat and (ii) to vaporize the moisture present in product through the provision of the latent heat of vaporization. The removal of moisture from the interior of the product takes place due to induced vapour pressure difference between the product and surrounding medium. The moisture from the interior diffuses to the product surface to replenish the evaporated surrounding moisture.

The working principle of greenhouse drying is in which the product is placed in trays receiving the solar radiations through the plastic cover and moisture is removed by natural convection or forced convection.

Greenhouse drying are being adopted to reduce the losses and to increase the quality of the dried products. Solar energy is the most promising power source of energy for drying of agricultural products. Most of the farmers adopt open sun drying because it is abundant and inexpensive. But the open sun dried products are also subjected to remarkable losses due to environment. Losses of fruits and vegetables are estimated to be 30%-40% during drying under open sunlight. The post-harvest losses can be reduced by adopting advanced means of drying, i.e. greenhouse drying. The greenhouse dryer can be operated in natural and forced mode as required. Studies reveal that the greenhouse dried products are of superior quality and better colour retention as compared to open sun drying.

1.1 Introduction

Greenhouse effect, regulated by the presence of greenhouse gases in the earth’s atmosphere, is a natural process that plays a major part in shaping the earth’s climate. A continued rise in concentration of the greenhouse gases has led to enhanced greenhouse effect resulting in global warming and global climate change. The impact of human activities on greenhouse gases (GHGs) emission through fossil fuel burning, agriculture and industrial processes is important and familiar to people. This chapter addresses basic principles and physics of greenhouse effect and the role of Indian agriculture in GHG emissions. Agriculture is a potential source and sink to GHGs in atmosphere. It is a source for three primary GHGs: CO₂, N₂O and CH4 and sink for atmospheric CO₂ . Management of agricultural land, land use change and forestry has a profound influence on atmospheric GHGs concentration. The two broad anthropogenic sources of GHGs emission from agriculture are the energy use in agriculture (manufacture and use of agricultural inputs and farm machinery) and the management of agricultural land. Large sections of the India’s population depend on biomass resources like wood, crop residues and cattle dung for energy. In the agriculture sector, besides the CO₂ emissions due to burning of crop and animal waste, India’s large ruminant population and rice fields are significant contributors to CH₄ emissions. An understanding of GHG emissions by sources and removal by sinks in agriculture is important to take appropriate mitigation and adaptation strategies and to estimate and create inventory of GHGs.

The variety of greenhouses and greenhouse material, equipment and accessories are so many. However, there are certain basic materials that essential in almost all types of green houses. These are

Structural framing materials

Such materialsinclude low maintenance non-heat conducting timber; strong and durable galvanized steel; or light, low-maintenance and sturdy aluminium alloys. Though plastic pipe frames are usable, they are not very strong to withstand snow load or strong wind sheering forces. What one should choose as the framing material would be determined by the material one wishes to use as glazing, his budget and the permanence of the structure one desires. Aluminium is a popular material for greenhouse framework because it is relatively lightweight, rustproof, affordable and easy to assemble. The downside is that it is not a good insulating material and in very cold weather, heat loss from the metal frame could inflate your heating bill. Also, you would need to look for sturdy frames if your greenhouse is located in an area that experiences high winds. Condensation could also occur on an aluminium frame. Wooden structural frameworks for garden greenhouses are also a popular choice for its aesthetic value, natural feel and the ’warmth’ it exudes. It is an easy material to work with especially if you are not using a greenhouse kit for building. Some greenhouse owners would settle for nothing else as they believe it is the only material that complements the natural beauty of plants inside the greenhouse! Wood is a good insulating material so it will not allow heat loss in cold weather. Reinforced wood has superior strength and has an excellent load bearing capacity. Being a natural material, it has the potential to develop mildew or disease and offer a haven to tiny pests. So, when you choose wood to build the framework of your greenhouse, be sure that you pick a high quality hardy wood such as redwood, cypress or cedar. Also, treat wood with non-hazardous chemicals so that your plants are not adversely affected. The preservatives used for wooden greenhouse frames should be pressure treated, salt type or copper naphthenate. Copper naphthenate is a general use preservative used for pressure treating utility poles and timber. It is known to be very effective in preventing mould, mildew and dry rot. It works very well against wood-damaging fungi and insect pests. Pentachlorophenol is a restricted use wood preservative and is toxic to plants and humans. It is not available to the general public and poles or timber treated with it are not suitable for use in a greenhouse. PVC pipe can also be used as support for small greenhouses that are to be covered with polyethylene, but PVC requires additional support to withstand strong winds. Being flexible, PVC can be used particularly well in hoop houses. Though it has the advantage of offering insulation and, if UV treated, are long-lasting, they are not good at bearing the load of hanging baskets and shelving to any appreciable degree. PVC that is treated to be resistant to ultraviolet radiation is also known as UPVC.

Introduction

Precise and continuous measurement the greenhouse gases (GHGs) fluxes/ emissions in agricultural systems are required for accounting and budgeting of carbon. Further, the long-term measurements of GHGs fluxes are equally important as precise measurement. Therefore, high frequency and long-term measurement of GHGs across the cropping systems are essential for chalking out the GHGs emissions mitigation strategies. Various technologies with definite working principles are used for estimation of GHGs emissions in agriculture.

Greenhouse Gases Estimation Techniques

Two basic principles are followed to estimate greenhouse gases in agriculture. One is the collection of GHGs from the field and subsequent analysis of the concentration of gases through gas chromatography (GC). Another principle is based on sensors measurement with the help of infrared gas analyze (IRGA). The two techniques used for the measurement are (i) ‘closed chamber method’ (manual/automatic), and (ii) ‘sensor-based method’. Generally, the GHGs fluxes in agricultural crop field are estimated by ‘closed chamber method’ for methane (CH₄) and nitrous oxide (N₂O). And for carbon dioxide (CO₂) measurement either soil respiratory chamber or canopy chamber is used that measures CO₂ with the help of infrared gas analyzer (IRGA).

1.1 Introduction

Increased emission of greenhouse gases results in climate change which becomes one of the most prominent environmental issues to the world today. Carbon dioxide (CO2) is the major greenhouse gas whereas nitrous oxide (N2O) and methane (CH4) are other substantial contributors to climate change (IPCC, 2014, Tongwane et al., 2016). However, these gases are emitted in minimal quantities in comparison to carbon dioxide but impart more global warming effect by absorbing more infrared radiations (Oertel et al., 2016). The warming potential of one kg of CH4 is 23 times more than one kg of CO2 while  in the case of N2O, it was nearly 300 times more than CO2 (Ramaswamy et al., 2001, Bharti et al., 2019; Biswas et al., 2010). Around one-third of methane and two –thirds of nitrous oxide come from soil (Prather et al., 1995, Tubiello et al., 2015, Smith, 2016).

3.1 Chemistry of greenhouse gases (ghgs)

Greenhouse gases (GHGs) are atmospheric-gases that have capabilities to absorb and radiate-back the infrared (IR) radiation in the earth-atmosphere system (Figure 3.1). In this process the atmospheric-gases absorb and radiate- back IR radiation in lower atmosphere effectively emitting and absorbing heat energy heat energy. They maintain the heat budget of earth-atmosphere and keep our plant warm. If we typically see the chemistry of those gases, the key point is that they should have dipole moments. This is the property which makes them capable to absorb and radiate-back the range of IR radiation. In a molecule when valence-electrons are not equally shared in a bond between the two atoms, a slight positive charge is developed above one atom and a negative charge on the other atom. That charge difference of the different atoms in a molecule generates the dipole moment. For instance, in water vapour (H₂O- vapour), an unequal sharing of electrons and or separation of charge causes dipole moment. In H₂O, the centre has a positive charge at the hydrogen atoms and negative charges are located on the oxygen atom. The magnitude of dipole- charges, vibration and stretching of O-H bond generates certain frequency of the oscillating dipole moment that actually regulates the absorption capacity of IR radiation by H₂O vapour.

Naturally Greenhouse gases are cover as blanket on the Earth and kept it about 33⁰C warmer than it would be without these gases in the atmosphere. This is called as the “Greenhouse Effect”.

Over the past century, the Earth has increased in temperature by about 0.5⁰C and many scientists believe that this is because of an increase in concentration of the main greenhouse gases viz., carbon dioxide, methane, nitrous oxide and fluorocarbons. People are now calling this climate change over the past century the beginning of “Global Warming”.

There are several systems for greenhouse heating based on heat source and purpose or crops to be produced in greenhouse.

Electric heaters

Unit space heaters, either floor mounted or supported, are normally dependent on electricity supply supported by stand-by generators. Abroad they are fuelled with natural or bottled gas or fuel oil and use fans for heat distribution. This system requires a relatively moderate capital investment, is easy to install, and provides for easy expansion of facilities. If unit air heaters are used, they should be spaced and directed to blanket the entire area with heated air.

Hot Water Systems

Hot water systems utilize metal pipes that can be perimeter, under benches, or overhead fan forced unit heaters can be used. This system requires a boiler, valves, and other necessary controls. Hot water system is simpler to install and normally requires less maintenance than a steam system. Hot water systems are mainly used in smaller greenhouse.

Fast increasing population, changing climate, shrinking land and water resources are the major challenges before us to meet the food and nutritional security of the population at global level. Improvement in the production and productivity of crops are the immediate need to boost the availability of food and improvement economic conditions of the farmers. Greenhouse technology has shown tremendous potential in improvement in production and productivity of crops even under uncongenial soil and climatic conditions. The farmers having very small farm holdings in countries like Japan, Holland and South Korea have improved their income and living standards by adopting protected cultivation technologies. However, India is yet to trap the potentials of the technology. Modern green houses require uninterrupted huge electric power for control of environment (heating/cooling/air circulation etc), which is considered one of the major cause for global warming. High installation and running (energy) cost, high cost of production; poor government support and lack of farmers’ friendly/cost effective greenhouse technology are some other challenges. Low cost zero energy based solar greenhouse technology popularizes the green houses in small and marginal farmers of remote areas. Such greenhouses are specifically design using local resources and also to trap the natural solar radiation/ heat and maintain it for longer period. The designs do not require electric power which ultimately reduces the installation/running cost and also does not have the adverse effects on the environment. This will not only improve the economic status of the farmers but also provide nutritive food to their families and also enhance production and productivity of various crops in the country without deteriorating the environment.

In India, risk-prone, high altitude area constitutes the easternmost trans-Himalayan part of Ladakh and Zanskar range (Jammu and Kashmir) and some parts of Lahoul Spiti (Himachal Pradesh). Truly described as cold desert with low population density, Ladakh constitutes the easternmost trans-Himalayan part of Jammu and Kashmir in India, comprising two districts, Leh and Kargil, bordering Pakistan and China (Fig. 1).

Plants require proper environment for its growth and development. If environment is not suitable crop would not do well. To ensure proper environment to commercial crops for their better growth and development covered structures are used which provide microclimate appropriate for their growth and development. Growing of crops under such protective structures, also known as greenhouses, is termed as greenhouse technology. The structures harness solar radiation for photosynthesis in plants or can be provided with artificial lights (LEDs) for the purpose. The technology embraces many aspects of farming such as modelling of structures, agronomic practices for the production of the crop and the commercial viability of the venture. The technology ensures crop production in a cover more or less independent of natural prevailing environment. The covering or cladding permits desirable aspect of sun and air and help in modifying crop production environment inside. The modification of environment is aimed of creating micro-climate inside the structure/greenhouse most appropriate for the growth and development of the crop.

Hence greenhouse can be defined as a framed or inflated structure with claddings like glass polyethylene sheets, poly carbonates, fibre reinforced plastics and others in which plants are grown by creating microclimate conducive to crop for its growth and development with or without automation and mechanization. The purpose of growing crops under greenhouse conditions is to extend their cropping season and to protect them from adverse environmental conditions, such as extreme temperatures, precipitation and pests. A large number of greenhouses/poly houses have come up in almost all states of India. Though in infancy but greenhouse cultivation particularly in horticulture crops and nursery production is visible.

1.1 Introduction

The greenhouse industry is rapidly growing, particularly in mild climates, and is crucial for providing access to fresh and clean food. Greenhouses provide an optimal climate for crops to grow and protect them from outside pests. Furthermore, greenhouse production has the potential to reduce water waste and implement integrated protection and production (IPP). It is essential to consider the environmental impact of protected cultivation, and Life Cycle Assessment (LCA) is a valuable tool for evaluating these impacts.

Introduction

The recognition of environment as the desired precondition for human existence and development both by Millennium Development Goals (MDG) as well as Sustainable Developmental Goals (SDG) unquestionably shows its importance and necessity. The impact of climate change is fast getting into our understanding and are realizing the enormity of the situation. Consequently, global environmental issues are a growing concern among the people and communities of various regions today. The impending ecological disasters have forced the right-thinking people and organizations to seek an alternative in the form of managing natural resources without jeopardizing the developmental activities. The challenge is to enhance the standard of living compatible with ecology and environment. This underlines rather unquestionably the need to pursue a line of lifestyle and development design that is compatible with nature and the issue of the environment cannot left to languish at the bottom of priorities.

Landscaping is both science and art and is an aspect of the environmental impact of a hotel that needs to be addressed. Understanding and blending the elements of both nature and construction is effective landscaping. Whether Landscaping is extensive or small consumes a large amount of water, fertilizers and herbicides and generates solid waste.

Ecogreen’s Greenscaping Operation provides cost-efficient and environmentally friendly solutions for landscaping. Greenscaping operation deals with two aspects:

1. Solid Waste Management, and

2. Water Conservation

ABSTRACT

Grewia asiatica L. locally called ’Phalsa’ (Family Tiliaceae) is a multipurpose gregarious plants species native to Asian belts, grows profusely in tropical and subtropical forests. Plant yield berries rich in calories, proteins, carbohydrates, dietary fibers, vitamins, macro-and micro-nutrients such as calcium, phosphorus and sodium. Their parts can be used as herbal medicine for treatment of various diseases. Recently, CSIR-Indian Institute of Integrative Medicine Jammu (IIIM) has developed and released a variety of this plant for rural upliftment and for development of value-added products such health drink and nutraceuticals. From its matured fruits of cultivated variety, a value added product called Shivalik Health Drink was developed by IIIM. For extension, agrotechnology of this plant has been transferred to various geographic regions of India such as Punjab, Rajasthan, Jammu & Kashmir, Uttar Pradesh, Maharashtra and Andhra Pradesh. This species prefers hardy and can be able to withstand in drought environment. For development of drugs and value added products, several therapeutic research works have been carried out which suggested that this plant species possess antioxidant, antidiabetic, antimicrobial, hepatoprotective, antifertility, antifungal, analgesic and antiviral activities. Further, there is a need to focus on biotechnological intervention with aim to develop seedless varieties and new nutraceutical products.

Proper grooming and hygiene are essential for maintaining the health and well-being of pet dogs. Regular grooming not only keeps your dog looking and smelling good but also helps prevent various health issues such as skin infections, parasites, and dental problems. This article explores the key aspects of grooming and hygiene for pet dogs, including brushing, bathing, nail care, ear and eye care, dental hygiene, and general tips for maintaining a clean and healthy canine companion.

Brushing Benefits

• Reduces Shedding: Regular brushing helps remove loose hair, reducing shedding and keeping your home cleaner.

• Prevents Matting: For dogs with longer coats, brushing prevents mats and tangles, which can cause discomfort and lead to skin issues.

• Stimulates Skin: Brushing stimulates the skin and distributes natural oils, promoting a healthy coat.

Calorimetry

The process of measuring  the amount of heat generated by the combustion of a substance is known as calorimetry. The first successful calorimeter using oxygen under pressure for the combustion of substance in a closed vessel was devised by Berthelot in 1881. Subsequent development by Mahler in 1992, Atwater in 1899, and Parr in 1912, served to improve and to reduce the cost of the original Berthelot apparatus by variations in mechanical details.

Gross evaluation is generally done to get a rough idea of the quality of semen and to assess the semen producing capacity of the bull. This also gives a fairly good idea about the reproductive health and any pathological conditions of the semen donor. The following are recorded under gross evaluation of semen:

    11.1    Color and appearance of semen
    11.2     Semen Volume
    11.3    pH of semen
    11.4     Semen consistency/ Semen density
    11.5     Presence of foreign matter
    11.6     Gross motility

Definition: Ground covers are low growing plants which are useful for covering large areas in the landscape Or Ground cover refers to any plant that grows over an area of ground, used to provide protection from erosion and drought and to improve its aesthetic appearance. An ideal ground cover must be easily established.

Ground covers are living plants or non-living materials used to cover areas. In general, plant related ground covers have a creeping or prostrate growth habit and grow no taller than 60 cm. A good ground cover should be evergreen and provide a permanent covering. Effects that cannot be achieved with turf grass or other plantings are possible with ground covers. Ground covers provide variation in plant height, texture and colour.

Tikka or Leaf Spot
Cercospora arachidicola/ Phaeoisariopsis personatum
Diagnostic Symptoms
• Disease is caused by two different pathogens, namely, Cercospora arachidicola and Phaeoisariopsis personatum.
• The two pathogens mostly occur on the same leaves.
• The Cercospora arachidicola appears about a month earlier than the Phaeoisariopsis personatum.
• The two pathogens cause symptoms differing each other. Early leaf spot
• Sub-circular dark brown spots having 1 to over 10 mm diameter are produced on the upper leaflet surface.
• Spots are of lighter shade of brown on the lower side of the leaflets.
• Yellow halo is seen around the brown spots.
• Dark brown in colour on the upper leaflet surface where most sporulation occurs and a lighter shade of brown on the lower leaflet surface.

This chapter deals with the findings of the study along with the discussion based on the analysis. This study tried to represent its findings as per the objectives of the study. At the end of this chapter, interrelation has been made, an explanation has been tried to put out down and an attempt has been done to reveal the cause behind it. The results and their pertaining discussion are presented according to the specific objectives of the study.

Ground truth links image data with actual physical features and materials on the Earth’s surface. Gathering this type of data is crucial for calibrating remotesensing systems and enhancing the interpretation of the collected imagery. In artificial intelligence (AI), ground truth refers to data that has been confirmed as accurate and is used to train, validate, and test models. In data science, ground truth serves as the benchmark for accuracy, allowing data scientists to measure how well a model performs by comparing its output to verified real-world data. This ensures that machine learning (ML) models generate reliable, reality-based results. Ground truth is particularly vital in supervised learning, where algorithms rely on labeled data to learn how to classify inputs or make predictions. Proper data labeling or annotation is essential—without it, the data cannot be trusted as a standard for representing the real world.
UNDERSTANDING THE GROUND TRUTH
Ground truthing is the process of gathering on-site digital data about the condition of crops and the overall state of a field. This information is recorded at specific locations and complements the remote sensing data obtained through drones. Collecting ground truth data in the field is crucial for calibrating remote sensing outputs and supports the interpretation and analysis of the imagery. Obtaining reflectance spectra directly from the surface materials in their natural setting—commonly referred to as ground truth data—is vital for identifying unknown materials in multispectral and hyperspectral imagery, and for assessing the accuracy of the sensors. Since removing samples for lab testing can alter or destroy their surface characteristics, and because lab analysis isn’t feasible for large or remote areas, researchers rely on portable field instruments. These tools must deliver lab-quality measurements in the field, with lighting and viewing conditions that closely match those of satellite or aerial sensors.

3.1. Ground water development

3.1.1. Rain water harvesting

Collecting and using precipitation water from a catchments surface.

Extensive rain water harvesting apparatus existed 4000 years ago in the Palestine and Greece.

In ancient Rome, residences were built with individual cisterns and paved courtyards to capture rain water to augment water from city’s aqueducts.

As early as the third millennium BC, farming communities in Baluchistan and Kutch impounded rain water and used it for irrigation dams.

Abstract

Water scarce state Rajasthan is without efficient and effective management. Water, when at surface is cheaper and like free commodity to use. Most of it gets evaporated rapidly due to aridity. There is no water during summers and drought years. This is now critical time to rethink and review our planning and policies and make it ground water oriented instead of completely surface water based. Ground water management should be the thrust area and key issue. There is need to conserve andharvest each drop ofwater especially for recharge to ground water. Utilize the augmented ground water resources as crisis management during long dry spells. Also, enforcement of regulatory measures, creating awareness among masses and participatory approach ofmanagement are the key factors for ensuring sustainable availability of water resources.

17.1. Introduction

Grounded Theory (GT) is a systematic methodology in the social sciences that involves the construction of theories through methodical gathering and analysis of data. Developed by Barney Glaser and Anselm Strauss in 1967, GT is widely used in qualitative research to generate theories that are grounded in empirical data. Unlike traditional research methods that test hypotheses, GT allows theories are to emerge from the data itself, making it a valuable tool for exploring complex social phenomena.

This chapter provides an in-depth exploration of Grounded Theory, including its origins, key principles, methodologies, applications, and criticisms. By the end of this article, readers will have a thorough understanding of GT and its significance in qualitative research.

Introduction

Groundnut (Arachis hypogaea L.) is an important traditional oilseed crop of India contributing to 3.9 million tons of global vegetable oil ranking the sixth in the sequence of oilseed crops. Added to its importance as an oilseed, groundnut is also an important food legume cultivated in an area of about 22 million hectares worldwide leading to a production of 38.6 million tons as per the FAO statistics of 2011 (ICRISAT, 2017). China and India are the leading groundnut producers followed by USA and Nigeria. Africa with 12.40 m ha area and 11.54 m tons of production, and Asia with 11.87 m ha and 29.95 m tons, together account for 95% global groundnut area and 91% of global groundnut production. There was a substantial increase in global groundnut production by about 5 m tons in 2013, from 40 m tons in 2012. In the last decade, 2004–2013, global groundnut production increased by 24%, contributed by 7% increase in groundnut area, and 16% increase in yield. The projected global demand for groundnut and its related products is expected to increase and so there is a need to further increase production and productivity to meet the demand.

Among the different oilseed crops grown in India, groundnut is the major crops grown in kharif / monsoon season. Among different states if India, Gujarat is the prominent state growing groundnut.

Groundnut has a long history of cultivation since the plant was domesticated and cultivated by the indigenous tribes such as Incas of Peru in South America for more than 1500 years. It is believed that the cultivated groundnut was introduced into India by the Spanish colonizers (Krapovickas, 1968). Groundnut is believed to have been introduced into the USA by the African slaves. Groundnut crop has found an ecological niche in the tropical and warm temperate zones of world, due its impressive adaptability.

I. FILL UPS

1. Groundnut contains _____ oil.
2. Groundnut contains _____ protein.
3. Groundnut is a _____crop.
4. Stigma receptivity is for _____ after anthesis.
5. Fertilization occurs about_____ after pollination.

Oilseed crops are crops which are rich in fatty acid, cultivated for the production of vegetable oil. They are used either for edible or industrial or medicinal purposes. The important oilseeds are groundnut or peanut, sesame or gingelly, sunflower, rapeseed and mustard, soybean, castor, linseed or flax, niger and safflower.

Groundnut also known as peanut or monkey nut (Arachis hypogaea L. 2n = 4x = 40, allotetraploid, a species of the legume or bean family, Fabaceae, essentially self-pollinated, with genome 1C=2891 Mbp) is one of the five major oilseeds, namely, soybean, sunflower, groundnut, cottonseed and rapeseed. The global acreage, production and yield during 2018-19 have been 27.49 million hectares, 46.81 million tons and 1700 kg per hectare. The preliminary corresponding figures for 2019-20 have been 26.75 million ha, 45.87 million tons and 1710 kg per ha (USDA, 2000). India and China with more than 4.5 million ha each account for nearly one third of total global acreage and fifty percent of global production (China, 17 million tons and India, 6.69 million tons). Other countries in descending order in terms of area are Sudan, Nigeria, Senegal, Myanmar, Niger, Chad, Guinea, Uganda, Congo and Mozambique. Productivity-wise, USA tops the list (4480 kg/ha) followed by China (3750 kg/ ha). India with 1400 kg/ha is at the average position.

14.1 Introduction

Groundwater is an important source of water for irrigation. It is the most abundant fresh water resource of the earth. Underground water reservoirs contain large stock of fresh water resources. Total quantity of groundwater within 800 m distance below the ground surface is more than 30 times the total water in all fresh water lakes, more than 60 times the total water in soil and other unsaturated rock materials, more than 300 times the water vapour in the atmosphere and 3000 times the average volume of all rivers and rivulets in the world (Lenka, 2001). But the distribution of groundwater is not uniform. At some places, it lies below a few metres whereas at other places, it is a thousand metres or more below the ground surface. In some places, there is abundant groundwater potential whereas at other places there is meager potential.

Groundwater is the water reaching the groundwater reservoir from the infiltrated water of precipitation which constitutes an important component of the hydrologic cycle. It is only the part of the subterranean water that occurs in the saturated pores of the containing rock materials underlain by water held in a zone of aeration. It should not be confused that all the water present in soil below the ground surface is groundwater.

ABSTRACT

The over extraction of water from the coastal environment, results in reduction of groundwater resources which has reflected in lowering of water level. In general, the depletion of water level enhances the landward migration of saltwater wedge. Pondicherry is one such region with recent alluvium as the major litho unit. A study has been attempted to calculate the extraction of water and to estimate the amount of recharge into this alluvial aquifer. The monthly water level fluctuation was observed for the study period in eighteen locations (20002002). The highest water level observed during 2000 was taken as the initial water level for the study and the subsequent decline in water level up to 2001 was monitored monthly until the rising trend was noted. This was taken as the fall in water level due to extraction. Keeping this as the initial value increasing trend was studied until there was a notice of decline in water level. This was taken as the rise in water level due to recharge. The spatial representation of these data in the above said eighteen locations were carried out by using GIS and the area occupied by different water level contours were calculated and the amount of water withdrawn was estimated. The maximum recharge was noted in the central and the northern part of the study area when compared to the other regions. Similarly, the maximum discharge was noted in the northern and the southern part of the study area.

Keywords: Rainfall, Recharge, Groundwater Budget, GIS.

Introduction

Large scale exploitation of groundwater using modern deep well boring technology and powerful pumps is the order of the day in India and elsewhere. Increase in agriculture area and year around cultivation of water intensive crops, frequently failing monsoons (Fig.5.1) all have led to drying up of surface water and increased dependence on groundwater.

Thus, given the scenario of over exploitation of the available groundwater, it is essential that proper storage and management of available groundwater resources be identified.

Introduction

The science of hydrogeology is defined as hydrology with emphasis on geology. This chapter is to refresh your geology knowledge. The key words are highlighted to assist a quick review.

The Crust and its Composition

The thin outermost layer of the earth is called the crust and ranges in thickness from about 8 km under the oceans to about 25 km on land. It extends under both oceans and continents, and forms the source for all the soils, vegetation, and gases in the atmosphere.

The crust is primarily composed of two elements: silicon and oxygen which account for 75% of the earth’s crust. Note that these are the two elements found in quartz (e.g., sand), which suggests this is the most common of all minerals.

Hydraulics of wells means the laws that are applicable to understand the flow of water through the formation and certain aquifer properties that determine the discharge of a well. Darcy’s law is used in studying groundwater flow though Darcy’s law is not valid under certain cases.

8.1  Water Bearing Formation

The earth’s crust is called the lithosphere which consists of hard rocks and disintegrated rock materials. The outer parts of the earth’s crust are porous and containing partially and fully filled up with water. The surface strata of the earth is partially filled with water and is called as zone of aeration and the zone below this which is completely filled with water is called the zone of saturation. The zone of aeration is divided into (i) the soil water zone (ii) the intermediate zone and (iii) the capillary fringe (Fig.8.1).

Q. 1 The development of a tube well should be started from :-
(A) Middle of screen      (B) Top of screen
(C) Bottom of screen     (D) Bottom of casing pipe

Introduction

Groundwater investigation has a long history. In the past a waterman in the village would walk around the investigation area with a Y shaped wooden fork and identify the location for digging the wells. Certain trees and organic landforms like termite mounds were considered as indicators. The native intelligence of local topography should have played a role in identifying potential location. Successful or otherwise the method can be said to lack scientific objectivity. The optimal groundwater surveying method is no doubt drilling. This method ensures that all necessary information is being brought up from the geological formations. However, in order to obtain a desired degree of information from the subsurface of an area, drilling alone is normally not a feasible alternative.

There are a number of efficient and inexpensive geophysical surveying methods available to the hydrogeologist. It is worth noting at this point that these are, without exception, indirect methods. This implies that no method measures directly what we are actually looking for. With geophysical surveys, the target features are therefore invariably associated features. This implies that unless we understand the water context of these features, our geophysical surveys will be less than meaningful.

Objective methods of investigating groundwater are discussed in this chapter.

Groundwater is a precious renewable resource which gets replenishment from the precipitation. Total water resources of the world are estimated at 1.37 x 10⁸ million ha-m. Of these, about 97.2% is salt water, mainly in oceans, and only 2.8% is available as fresh water. And, out of this 2.8%, about 2.2% is available as surface water (2.1% is fresh water in glaciers and icecaps, 0.1% is available in lakes and reservoirs, 0.0001% in streams) and 0.6% is available as groundwater. Only 50% of groundwater resource is economically extracted with available technology. Presently, 1.3 x 10⁴ million ha-m fresh water in reservoirs and 41.1x10⁴ million ha-m groundwater is theoretically available to provide usable water for drinking, domestic use, irrigation, etc., to mankind. Groundwater is the largest source of fresh water excluding the polar icecaps and glaciers. The amount of groundwater within 800 m from the ground surface is over 30 times the amount in all fresh water lakes and reservoirs, and about 3000 times the amount in stream channels, at any one time.

Introduction

Fresh water, a renewable but not an infinite resource, is becoming increasingly scarce. The amount available for use to the world today is almost the same as it was 4500 years ago but global demand has been increasing exponentially. Since 1950, the renewable supply per person has fallen 58 percent as world population has swelled from 2.5 billion to 6 billion. Moreover, unlike oil and most other strategic resources, fresh water has no substitute in most of its uses. It is essential for growing food, manufacturing goods, and safeguarding human health.

According to a World Policy Forum report, the largest and most combustible imbalance between population and available water supplies will be in Asia, where crop production depends heavily on irrigation. Asia today has roughly 60 percent of the world’s people but only 36 percent of the world’s renewable fresh water. China, India, Iran, and Pakistan are among the countries where a significant share of the irrigated land is now jeopardized by groundwater depletion, scarce river water, a fertility-sapping buildup of salts in the soil, or some combination of these factors. Groundwater depletion alone places 10 to 20 percent of grain production in both China and India at risk.

Introduction

All models are but approximations of reality. When we approximate there is always room for uncertainty. The preference of a particular model over the other is the relative degree of uncertainty acceptable to the objective and budget of the study. With the advent of computers, hosts of modeling software promising a lot to the researcher have arrived on the horizon. It is not in the scope of the book to enumerate all the techniques of hydrogeological modeling. Physical modeling using sand tanks was the earliest attempted modeling technique, about 107 years ago. Most recent and significant modeling technique practiced by many in groundwater potential identification is Geographic Information System (GIS) based modeling. After a brief treatment of physical models, concepts of mathematical models and GIS modeling are elaborated. The modeling techniques have involved mathematics and or software specific instructions. Hence it is recommended that relevant text books for individual techniques be referred. This chapter deals more on modeling concepts.

Key words : Groundwater Modelling, GIS, PMWIN, ArcInfo Interface Con2grid, Interface Programme, ArcMacro Language.

Introduction

Groundwater is an important source of irrigation in India and has played a major role in increasing the food production. About 50 per cent of total irrigated area in the country is dependent on groundwater (Central Water Commission (CWC), 2000). Productivity of groundwater is normally more than the surface water due to the fact that it is available at the point of use, requires minimum conveyance infrastructure, is available on demand and maximizes the application efficiency. However, in past few years, excessive and unplanned groundwater pumping in certain parts of the country has resulted in depletion of groundwater resources. Water table in these region is going down day by day and making it beyond the reach of poor farmers. Therefore, keeping the water table in the desirable range is a major concern. This can be achieved by adopting proper pumping rate and pumping schedule. Groundwater modelling has successfully been used for deciding the pumping rate and pumping schedule. Groundwater modelling refers to simulation of groundwater behaviour under varying pumping and recharge conditions. A groundwater model is simply a set of equations, which describe the physical processes active in the aquifer subjected to certain assumptions. While the model itself obviously lacks the detailed reality of the groundwater systems, the behaviour of the validated model approximates that of the aquifer.

Introduction

Water is one of the most complex natural resources demanding a comprehensive understanding of its inherent features in occurrence and distribution for an integrated planning aimed at optimum development for agriculture, health, industry, power, etc. The well being and development of our society is dependent on the availability of water. An increase in groundwater development and utilization for industries and urban water supply has created improper disposal of liquid waste. Defective well constructions, sewage and waste disposal in man made lakes within city, open quarries with water and failure to seal the abandoned wells in city area have provided possible openings for downward movement of polluted water into subsurface formations without undergoing the process of natural filtration.

Abstract

Water is an essential and vital component for our life support system. Drought and floods are the extreme events of rainfall and the vagaries of monsoon and hydrogeological framework in the country are highly variable from place to place. The water resources available in the country are also not uniformly distributed. The changing Landuse pattern and population growth and the resultant water resources development has lead to water stress at many places. In such areas, the extraction of excessive quantities of groundwater has resulted in the drying up of wells, damages of ecosystems, land subsidence, salt-water intrusion and other related problems. Agricultural, urban & industrial wastes are increasingly threatening the groundwater quality, which is likely to become a more serious issue in the coming years. Considering the seriousness of the groundwater contamination, Central Ground Water Board has carried out detailed studies in few hot spots in the state of Tamil Nadu. The issues related to the water resources contamination and the findings of the studies in parts of Tamil Nadu are summarized in this paper.

ABSTRACT

Over the past four decades groundwater has become a topic of discussion and investigation and as a result the knowledge of understanding groundwater conditions has radically improved. For the past quarter century, remote sensing has played a vital role to target the groundwater resources for the essential survival of horticulture and agriculture crops in drought-prone areas. GIS technology has made a rapid stride for the past one decade to amalgamate the data generated from various space-born platforms and the ground based surveys to facilitate the generation and use of various thematic information for groundwater resources assessment. The present study aims for the demarcation of various groundwater prospective zones in the West Doon Valley and its environs, falling in the SOI toposheet 53 F/15. The role of various parameters namely, Geomorphology, Geology, Lineaments, Drainage, Land Use, Water table and Slope has been integrated for delineating groundwater prospective zones. IRS IC LISS-III geocoded satellite image on 1:50,000 scale was used. Index overlay model has been applied for GIS analysis. The resultant map indicates five prospective zones, such as poor, low, moderate, high and very high groundwater prospective zones in the study area.

ABSTRACT

Identification and mapping of fractures/lineaments and hydrogeomorphic units is prerequisite for undertaking ground water exploration and development in any terrain. Remote sensing and GIS techniques have been used for ground water potential mapping in Theni District. The study area has been divided into various geomorphic units based on visual interpretation of LISS III and PAN merged data in false colour composite on 1:50,000 scale. Ground water potential of each of the geomorphic units was assessed and correlated with geology, structure and recharge factors prevailing in the Theni District.

Technical Term       Definition

Groundwater         Water present in the zone of saturation (below water table) is called groundwater

10.1 Introduction

During rain or heavy irrigation, a part of the rainfall or irrigated water moves below the effective root zone of the crop which moves further below and adds to the water table lying above the impermeable bed or hard rock which is called as  ground  water  reservoir. At  times  the  accumulated  surface  water  is  also recharged to the soil reservoir both naturally as well as artificially that add to the underlying ground water reservoir. This groundwater is an important source of water for irrigation as well as domestic uses. It is the most abundant fresh water resource of the earth. Underground water reservoirs contain large stock of fresh water resources. Total quantity of groundwater within 800 m distance below  the  ground  surface  is  more than  30  times  the  total  water  in  all fresh water lakes, more than 60 times the total water in soil and other unsaturated rock materials, more than 300 times the water vapour in the atmosphere and 3000 times the average volume of all rivers and rivulets in the world (Lenka, 2001). But the distribution of groundwater is not uniform.

1. Result demonstration

It is a method of motivating the people for adoption of a new practice by showing its distinctly superior result. The demonstrations are conducted in the farm or home of selected individuals and are utilized to educate and motivate groups of people in their neighborhood. This is a very effective method for the transfer of technology in a community.

Objectives

1. To show the advantages and applicability of a newly recommended practice in farmer’s own situation.