eChapters

4.1 Introduction

Experts predict that the global population will exceed 9.6 billion by 2050. This, coupled with the rise of urbanization, the scarcity of arable land, and the destructive effects of climate change, poses significant challenges for agriculture and food production worldwide. To combat these challenges, new horticultural research techniques must be implemented to enhance productivity and efficiency, improve nutrition, and ensure food security, especially during times of crisis like the COVID-19 pandemic. Greenhouse technology has made remarkable strides in recent years, allowing for the manipulation of internal growth elements like temperature, light intensity, and CO2 concentration to create optimal growing conditions

5.1 Irrigation Channels
Canal or channel is an artificially made conduit through which water is supplied to the field from river, tank, reservoir or wells. The open channel is the most common type of water conveyance system. If the pipes and drains are partially full behave like open channel. The irrigation channel may be lined or unlined and the flow is either uniform or varied.

The canal may be classified in following ways.

a) Classification based on the source of supply i) Permanent or perennial canal ii) Inundation canal

A canal is said to be permanent when it is fed by a permanent source of supply and has permanent networks of distribution of supplies. Inundation canals draw their supplies from river usually when water stage exceeds a predetermined level. Headworks are not provided for diversion of river water to canal. However, canal head regulators are provided to regulate the canal head as required time to time to accommodate the changing pattern of river course.

5. 1 Irrigation Channels

Canal or channel is an artificially made conduit through which water is supplied to the field from river, tank, reservoir or wells. The open channel is the most common type of water conveyance system. If the pipes and drains are partially full behave like open channel. The irrigation channel may be lined or unlined and the flow is either uniform or varied.

The canal may be classified in following ways.

(a) Classification based on the source of supply

(i) Permanent or perennial canal

(ii) Inundation canal

A canal of approximate discharge of less than 80 cumecs (3000 cusecs) discharge may be called a medium or low capacity canal).

3.1 Mehboob Section

A Mehboob Section is only a modification of best trapezoidal section by making its complete bottom circular as shown in figure 3.1. Also see figure 1.6 and para 1.7. That is why these canals are also known as canals of zero bed width, or trapezoidal canals with curved bottom, or cup shaped canals.

But these cannot be called as triangular canals with curves, as often spoken. In fact it is a truncated triangle circumscribing the semi circle. Trapezium is also a truncated triangle circum scribing a circle.

More accurately it can be said as a combination of semi circular and best trapezoidal section so as to take full advantage of their hydraulic efficiency and practicability.

This is such a beautiful section that the designer can never commit a mistake, even if he wants to commit a mistake. The dimensions are so geometrically fixed that no one can play with any dimension.

The value of this section was realised for the first time by Er S I Mehboob (1943) in his Punjab Irrigation Branch Paper No.260" Lining of Canals". There after this canal section became well known as Mehboob Section after his name. He also stated that the most economical section i.e. the maximum area for the minimum perimeter is when the centre of the arc is at the full supply line of the section. This is also evident in figure 1.6. This is also the condition for all best hydraulic sections. This section is also useful to a higher silt carrying capacity than a wide shallow one..

Abstract

The paper presents the innovation of solar tunnel dryer; it is a walk in type semi-cylindrical poly house framed structure with UV-stabilized polythene sheet, where products on large scale could be dried under controlled environment. Chilly drying in solar tunnel dryer to reduce the moisture content from 83.4 % (w.b.) to about 9 % (w.b.) and Aonla pulp from moisture content of 81 %(w.b.) to safe moisture content 9.5 %(w.b.) successfully dried. 20-30^ºC of higher temperature was obtained in solar tunnel dryer over the ambient temperature, depends on product. In comparison to open sun drying to obtain the same level of moisture contents resulting in a net saving in drying time of 40-50% for solar tunnel dryer over open sun drying.

A. Rectangular Canals

5.1 Design of Best Rectangular Canals

After the Mehboob and Trapezoidal canals, next best section is rectangle. This section is also generally adopted for small discharges say upto 10 cumecs (350 cusecs). This section ranks at No. 4. Yet, this is the only section most commonly adopted for flumes of discharges upto140 cumecs (5000 cusecs). Typical example is Orsang acqueduct, 1 km. long for 1140 cumecs (40000 cusecs) in ractangular sections on Narmada Canal Project, Gujrat, India, built in the years from 1990 – 2000. Such sections are common in power house canals due to limitation of space and very sharp curves. It is free from the effect of change of side slopes as in the trapezoidal canals (see para 3.3) Still some small side slope (batter) is adopted in thick masonry / concrete lining. It adds to structural stability with economy in thickness of wall and as well as hydraulic efficiency. It may still be called as rectangular section.

Details of its hydraulic efficiency in comparison to semi circle, Mehboob and trapeziodal sections are discussed in chapter 1, para 1.8

The pipe network in a drip system consists of a mainline, sub mains, laterals, and distributors. The layout of the pipes depends on the physical factors like shape and size of the area, topography and any other obstacles in the field. In any field there may be the scope of different layout of the pipes. The most economic one should be selected. In general, contour line is followed in laying the laterals in sloping land, sub main length usually be shorten in uphill and equally spaced laterals on either side of a sub main in a flat land provides good layout.

Hydraulic Formulae /Head Losses in Pipes

There are numerous equations for solving the head loss in pipes. The most commonly used are the Darcy-Weisbach, Hazen-William and Scobey’s.

P rotected cultivation technology envisages immense promise, especially for high-value crops against various biotic and abiotic stresses. The climatic parameters stress conditions like unusually low and high temperature, humidity, solar radiation, wind velocity comes under abiotic stresses. The present climate change scenario dealing with various biotic and abiotic stress conditions poses serious threat to agricultural production throughout the world. It is estimated that due to one-degree rise in temperature during rabi season, wheat production declines by 4-5 million tonnes in India. Similarly due to prevailing low temperature and frost like conditions, especially in Northern India, several million tonnes of horticultural crops like tomato, brinjal etc. got wasted every year. Protected cultivation technology deals with following types of protected structures :

A greenhouse with all measures of climate control is one important component for integrated greenhouse crop production and protection. However, the growing period is very often limited to few months in the year, because of insufficient ventilation and cooling in summer as well as heating in winter. Structures and shapes of greenhouses are adapted insufficiently to climate conditions. Climate control and greenhouse structures have to be adapted and optimized with regard to outside climate, and growers must be trained in these adapted technologies. A greenhouse structure with light transmittance (through framework and cladding material), ventilation, heating, cooling, and protection from insect pests by screening, as well as all influences of management, irrigation, fertilization, water quality, physical and biological plant protection is an integrated system. Greenhouse structures should be designed according to the climate conditions and to the general design criteria, as well as to the locally available and cost-effective materials. The import of greenhouses from countries with a different climate fails very often, because they are not adapted to the local conditions. Even an appropriate greenhouse structure can fail if mounting and continuous maintenance are not guaranteed. Temperatures and global radiation allow open-air crop production throughout the year in many subtropical and tropical countries.

Vegetable and flower production are significantly influenced by the seasonality and weather conditions. The extent of their production causes considerable fluctuations in the prices and quality of vegetables. Striking a balance between all-season availability of vegetables and flowers with minimum environmental impact, and still to remain competitive, is a major challenge for the implementation of modern technology of crop production.

Aim

To design a screw conveyor

Theory

The screw conveyor consists of screw blade, screw shaft, coupling, tubular trough, cover, inlet and outlet gates, bearings and drive mechanism.

A shaft with spiral screw revolves in the tubular trough. The screw shaft is supported by end and hanger bearings. The rotation of screw pushes the grain along the trough.

The screw blade or flight is a continuous one-piece helix, shaped from a flat strip of steel welded on to the shaft.

The screw shaft is usually a joint less tube with thick sides and a high tensile strength to reduce the weight.

Concept: Operations conducted before and after harvest are essential components of the system for producing high-quality seeds. If enough care is not taken in the initial stage, there most likely won’t be any resources left to get high-quality seed. Like this, carefully produced, high-quality seed may lose a significant percentage of its worth if post-harvest management protocols are not adhered to. Its quality is highly correlated with soundness, fullness, and homogeneity of physical characteristics (size, shape, density, colour, and appendages), in addition to mechanical planting’s simplicity and improved crop establishment. Improving the seed that has been gathered and getting it ready for secure storage till needed are accomplished through the effective and efficient process of seed processing. To increase the quality of the seed lot, the goal of seed processing must be to optimize the physical properties of the seed and the constituents of the harvested seed mass. The three main steps in seed processing are conditioning, grading, and applying protectants or enriching with nutrients. These steps are completed in compliance with established protocols and standards (McDonald and Copeland 1997; Agrawal 1996; Jorgensen and Stevens, 2004). The distinct qualities of the crops and the surroundings are taken into consideration while adjusting the machines and operations.

Aim

To design shallow and deep bins

Theory

The structure behaves as a deep or shallow bin depending upon its relative dimensions such as depth and diameter or width. It is decided from the concept of the plane of rupture.

Plane of rupture: The plane of rupture is that surface down which a wedge of material bounded by one wall face, the free surface, and the plane of rupture would start sliding if bounding wall were to move.

A canal of more than 80 cumecs (3000 cusecs) approximetly may be called as a high capacity canal.

It has already been pointed out in chapter 1, that for the best section of any shape, R is always equal to d/2 only, and such depth is the most optimum depth. But such channels are not always practical or most economical due to many other practical reasons, (see para 4.1 and 6.3) and many times shallower depth then this depth is adopted. Typical examples are lining of existing earthen channels, given in para 6.3.

All the best sections have fixed ratio of dimensions very near to the semi circle. For large discharges, radius of semi circle increases that, means depth of canal as well as velocity increases. But higher velocity is not permissible with every type of lining (see table 2.1 and para 2.3). Similarly depth also has limitation of construction, maintenance, stability of slopes, etc. see example–4.2.

Because of limiting velocities and depth, deeper canal section are not practically feasible/possible. Therefore for large discharges, say more than 100 cumecs, Mehboob or best trapizodal sections are just not possible/practical, and recourse has to be taken to trapezoidal section with increased bed width then depth. This section is hydraulically inefficient or uneconomical. Larger the B/D ratio, larger is the inefficiency and section is more costly. (For Mehboob Section, B:D ratio is zero and for best trapizodal section it is much less than 1, see para 3.1, table 3.1 para 3.5 and table 3.4).

Kaushik Kumar

Design Thinking

Design thinking has emerged as one of the skill set in the recent competitive environment.Basic science has been mainly involved in development of various models that fulfills the requirements of engineering domain.

However, the engineering graduates being produced did not possess the required industrial skills and hence were perceived by academia and industrialists as ineligible to be employed in various industries.

Chicken’s eggs have been used as a food item by human beings since antiquity. The egg is composed largely of the proteins out of the three most important dietary essentials (proteins, fats and carbohydrates). The egg proteins are highly digestible and remarkably complete, containing the most important essential amino acids. The amino acid profile of egg is similar to the ideal balance of amino acids needed by humans. It also supplies various minerals, some in significant amounts, and contains a range of vitamins. The nutritive excellence of the egg enhances the value of any food in which it is incorporated. Meeting consumer demands is a constant challenge for the poultry industry. Present day consumers desire somewhat distinct products with respect to safety, healthfulness, freshness, taste, color, etc. To remain competent, various companies have developed several designer and specialty eggs which have appeared in supermarkets.

14.1 Introduction

Eggs are an essential food for humans due to the high nutritional quality and quantity that they contain. Eggs are one of the most consumed foods all over the world because of its nutritious profile, range of uses, and relatively inexpensive cost as a food source. Intakes of total lipids, cholesterol, and saturated fatty acids in human diets can be attributed, in part, to the consumption of animal products. Due to the high amounts of cholesterol (about 200-300 mg/100 g) and saturated fat (approximately 3 g/100 g), eggs have been considered to be contentious foods by several health organisations and nutritional experts.

Abstract

Designer foods are known by various names like medical foods, fortified foods, nutritional foods, nutraceutical foods, pharma foods etc. These foods are nutritious, maintain health and prevent diseases. Such foods must possess characteristics like modified composition; limit the presence of certain potentially harmful components and include certain desirable ingredients either naturally or by intentional addition. The term designer food emerged some years ago to describe foods tailored to specific concentration and proportion of nutrients that are important to health. These are designed and produced by using different approaches. The term ‘designer foods’ is subjected to change based on nutritional labelling regulations, new developments, consumer perceptions and expectations. Grain improvement through biotechnology emphasizes crop upgrading with a specific challenge to manipulate the endosperm composition in order to improve its intrinsic properties for diet and health. Breeding fruits with higher bioactive compounds for disease resistance and improved composition have stimulated interest in the nutraceutical and processing aspects of the fruits Nutritive and genetic interventions to alter milk composition for specific health and processing opportunities are gaining importance in dairy biotechnology. Designer eggs having modified fat provide choices with different nutritional benefits. The options suggested for designer meat and meat products are through production practices, post-harvest procedures and reformulation techniques. All these features of designer foods will be presented with suitable examples.

In recent years, oilseed crops are being increasingly exploited for production of pharmaceuticals, surfactants, plasticisers, emulsifiers, detergents, lubricants, adhesives, cosmetics, oleo-chemicals, biofuels apart from their demand for their healthy vegetable oils and livestock feeds (Metzger and Bornscheuer, 2006). The increased interest resulted in an 82% expansion of oilseed crop cultivation areas and about a 240% increase in total world production over the last 30 years (Rahman and Jimenez., 2016).

This chapter introduces specialty eggs whose composition, production system or marketing attributes differ from conventional eggs. It examines designer eggs, omega-3 enrichment, vitamin and mineral enrichment, organic egg production, free-range and cage-free systems, and welfare-oriented production. The chapter also addresses labelling, certification, consumer trust and the market prospects of specialty eggs. Particular attention is given to the biological basis and technological limits of nutritional enrichment and to critically evaluating claims concerning nutrition, welfare, safety and environmental benefits.

Objective

    1.    Design drum priming (2-3 kg and drying unit with house hold or commonly available materials.
    2.    Standardization of time for seed priming for different crops.

Probable drum priming unit components

A] A vertical drum which need to be rotating
B] A motor which will rotate
C] A desktop assembly
D] A simple two way seed drier (Fig not given here)