eChapters

1.     Which of the following micro-organism is the most heat-resistant in low acid canned foods and its destruction is considered the criteria for successful heat processing?

(a) B.subtilis

(b) C.botulinum

(c) C.sporogenes

(d) B.mycoides

2.    D value represents

(a) Doubling time

(b) Generation time

(c) Decimal reduction time

(d) Decimal reduction temperature

6.1 Introduction

In general, the terms drying and dehydration are interpreted as the removal of moisture from a food product. Removal of moisture from a food product offers an excellent protection against most common causes of food spoilage. The drying or dehydration process achieves such protection by reducing the moisture content of the food product to levels which are adequate to limit microbial growth or other adverse chemical reactions. During drying, heat and mass transfer occur simultaneously (Figure 6.1). Heat is transferred from the bulk gas phase (i.e. hot air used for drying) to the solid phase (i.e. food product to be dried), where part of it is utilized for vaporization and the remainder is taken up by the solid phase as sensible heat. Mass (i.e. moisture of food product) is transferred in the form of vapour through various resistances, first from the interior of the solid to the surface, then through vaporization at or near the surface and finally in transport of the vapour into bulk gas phase. Dehydration is the removal of moisture close to bone dry condition.

Abstract

The present study was conducted to develop ready to eat extruded snack food based on germinated flour of wheat, Bengal gram and green gram. A Central Composite Rotatable Design (CCRD) for five variables at five levels was used for experimental combinations and optimization of the process parameters. Experimental design with green gram flour (5 to 20%) and bengal gram flour (1535%) in wheat flour, moisture content (14-18%), screw speed (200-300 rpm) and barrel temperature (126-134°C) as independent variables having 32 different combinations of snack formulations that were studied using response surface methodology to investigate the effect of these variables on product responses (Lateral expansion, bulk density, Water absorption index, water solubility index and sensory characteristics). Sensory analysis was carried out of all extrudates for texture, color and overall acceptability. Multiple regression equations were obtained to describe the effects of each variable on product responses. The optimum operating conditions for development of germinated wheat, green gram and Bengal gram flour extrudate were 132°C of barrel temperature, 275 rpm of screw speed, 17 % offeed moisture, 6.5% of green gram flour and 23.1% of Bengal gram flour. The responses predicted by the software for these optimum process conditions resulted lateral expansion of 169.59%, bulk density, 0.263g/cm³; water solubility index, 19.08; water absoption index, 13.88g/g; and overall acceptability value of 7.38.

16.1 Introduction

Food safety is most important issue in today's global environment. To safeguard food supply is a very difficult and challenging responsibility, as a consequence of which the world's largest food companies, retailers, and manufacturers have placed very high food safety standards. Although the safety of food has improved exponentially but progress is uneven and food borne outbreaks due to microbial contamination, pesticides, antibiotics chemicals and toxins are common in many countries. International trade statistics (2007) by World Trade Organization (WTO) reported that Europe has accounted for 46% of world exports of agricultural products, where food represents 80% of agricultural exports. The trading of contaminated food among countries increases the risk for outbreaks and consequently, health risks due to microbial pathogens in food are of major concern to all governments.

Biosensors are an important option in the agricultural and food sectors to control production processes and ensure food quality and safety by dependable, fast and cost effective methods. Biosensors have plenty of advantages over conventional analytical tools since they offer advantages in size, cost, inherent specificity, selectivity, rapid response, accuracy and sensitivity. Food microbiologists are always in search of rapid and reliable automated systems for the detection of biological activity. Biosensors provide sensitive, miniaturized systems that can be used to detect unwanted microbial activity or the presence of a biologically active compound, such as glucose or a pesticide. Immunodiagnostics and enzyme biosensors are two of the leading technologies that have had the greatest impact on the food industry. The use of these two systems has reduced the time for detection of pathogens such as Salmonella to 24 hour and has provided detection of biological compounds such as cholesterol or chymotrypsin. The another useful application for biosensors, is detection of genetically modified organisms (GMO), since several countries have laws regulating the commercialization of GMO products and their derivatives. Biosensors are also useful in the implementation of hazard analysis and critical control points (HACCP) plans by verifying process developments and correcting errors in due time. There is joint application of Biosensor technologies and nanotechnologies in many food and agricultural applications such as the development of nano-scale tools for biosafety, nanoscale compounds for food packaging, and nano-sensors for pathogen detection in animals and plants. These are helpful tools in the detection and control of potential food contaminants by the agricultural and food industries.

I. POST HARVEST DISEASES

A. Post-Harvest Diseases of Fruits

Food is composed of three main constituents viz; carbohydrates, proteins and fats and their derivatives. In addition to these constituents, inorganic mineral elements and diverse organic compounds like vitamins, pigments, flavouring compounds, enzymes, and acids are also present. Carbohydrates, proteins, fats and vitamins are organic in nature. The percentage of water is large in certain foods. The variation in structure, texture, colour, flavour and nutritive value is because of the varying proportions and arrangements of these constituents.

Carbohydrates are important in foods as a major source of energy, to impart crucial textural properties, and as dietary fiber which influences physiological processes. Digestible carbohydrates, which are converted into monosaccharides, which are absorbed, provide metabolic energy. Carbohydrates account for more than 70% of the caloric value of the human diet. It is recommended that all persons should limit calories from fat to not more than 30% and that most of the carbohydrate calories should come from starch. Non-digestible polysaccharides (all other than starch) comprise the major portion of dietary fiber.

Introduction

The term pesticide refers to any chemical or mixture of chemicals intended for preventing, attracting, repelling, controlling or regulating a pest, including unwanted species of plants and animals during the production, shipment, transit, storage, processing or distribution of any food or agricultural commodity. The term includes compounds classified as insecticides, fungicides, herbicides, accaricides, rodenticides, plant growth regulators, sprouting inhibitors, chemosterilants, desiccants etc. The term excludes substances like animal drugs and food additives. Pesticides are chemicals used to destroy or control weeds, insects or other pests. The term pesticide residue refers to the remnants of the pesticide after weathering and it consists of the parent molecule and the degradation products which are toxicologically significant. In general, the pesticides, by virtue of their inherent toxic nature are recommended to be used as per Good Agricultural Practices (GAP) only. If GAP is not followed, contamination of the produce with the residues may pose significant health risk to consumers, non target organisms, biota and environment as a whole. When a pesticide is used for pest control purposes, they may reside in the form of metabolites.

Pesticide residues occur as the leftover of any pesticide after its application for pest control and it includes the parent compound and its toxic metabolites. Pesticide residue analysis may be defined as qualitative and quantitative analysis of samples drawn from agricultural field, market and environment for pesticides and toxic metabolites. Pesticide residues are invariably present in micro – quantities and generally estimated at ppm/ ppb levels. After application of the diluted spray solution, they are present at sub microgram levels in the substrate and hence their estimation at ppm or ppb levels is very cumbersome and need to be performed with utmost care. Moreover, the residue data generated should be accurate, reliable and reproducible. The level of residue in any edible commodity has to be below their prescribed maximum residue limits (MRL) value for market acceptance and below maximum permissible intake (MPI) for safety to consumers. Pesticide residue data are mainly utilised by regulatory authorities for estimation of MRLs and for assessing impact on human health and environment, particularly their adverse effect on non-target organisms. The detection of the pesticide residues must be confirmed beyond doubt and confirmation by GC-MS/MS or LC-MS/MS is generally acceptable. Since pesticide residues include parent compounds, isomers and toxic metabolites, appropriate methods of detection should be selected so that all the components are measured separately. Environmental samples/ market usually contain residues of large number of pesticides, for which multi residue methods are required for estimation/screening of such samples.

Introduction

Food and water safety is a public health concern. “It is health that is real wealth and not pieces of gold and silver” is a famous quote by Mahatma Gandhi. To provide good health and to maintain it properly for all citizens, the country need to assure the quality and safety of food consumed by it's population (Attrey, 2016). Apart from nutrition and taste, a more important part of food is the safety standards during manufacture, storage, distribution, sale and import. Food safety is particularly important in India, where an inordinately high percentage of population suffer from malnutrition and food borne diseases (Bahuguna, 2016). Food borne diseases in India have increased the frequency of mortality and morbidity. Around 5.82 crore cases of food borne diseases and 3.51 lakh food associated deaths were reported in 2010. Nowadays the consumption of unsafe food is being considered as an alarming threat to the growing global food markets. Adulteration and synthetic milk in India, powdered infant formula with melamine in China and adulteration of beef in Europe are a few examples. These issues can be resolved to a great extent, through appropriate food laws and policies. A country should not only possess appropriate statutory, regulatory legislations, policies in place for the su-pply of safe and good quality food at all times, but also should assure that the same is imple-mented seriously (Attrey, 2017).

Apart from health, food safety is vital for economic growth and progress as well. In India, the food processing industry holds tremendous opportunity. It has high employment potential, can boost exports of agro-products out of the country and also provide better returns to farmers for their produce. The concept of food quality and food laws is not totally new in India because food was considered an important aspect of healthy living even in ancient India. India took an important step towards building a safe food culture a decade ago by enacting the Food Safety and Standards (FSS) Act. In one stroke, it brought about a paradigm shift in the way we look at food safety regulations in India. Food Safety and Standards Authority of India (FSSAI) are mandated under Food Safety and Standards Act 2006 to protect people from this threat. In its role of a food regulator, FSSAI can be proud that it touches the lives of each of the 1.3 billion people in the country. More than just reaching the people, the watchful eye of FSSAI is assuring them that the food they get in any form, raw or processed is safe to consume (Agarwal, 2016).

Postharvest food loss has been considered an unavoidable affliction since food storage first began. These losses are much more painful and costlier in terms of money and man-hours. Such losses due to plant parasitic nematodes, in particular, is severe in tropical regions especially in developing countries like India, where proper storage, transmit and marketing facilities are inadequate. In tropical agriculture, increase in production rate is generally low and, by itself, unable to keep pace with the requirements of the increasing population. Hence, such food shortage demands the need to reduce postharvest loss due to nematodes. Postharvest food losses also constitute a vast complex of physical and biological changes, which makes it very difficult to represent in a single figure. As suggested by different sources, an overall loss of at least 10 per cent occurs in the developing countries. However, the magnitude may range from negligible to cent percent in particular nematode species and crop.

In addition to causing direct losses individually, phytonematodes also favour the establishment of secondary, passive micro- organisms like fungi, bacteria, viruses etc. Nematodes cause mechanical wounds, which serve as avenue for the entry of secondary microorganisms (Ravichandra, 2008). This complex association results in severe damage to planting material.

Postharvest diseases due to nematodes can be managed through restricting the movement of infected planting material to uninfected areas; use of uninfected, healthy planting materials; use of treated planting materials; improvements in the cultural practices at the growing site; timely and careful harvesting; use of nematicides both at pre- and postharvest stages; employment of some physical means like heat, radiation etc; improved storage techniques and integration of these methods. By maintaining hygienic conditions during harvest, transportation, storage and packing most of the postharvest damage due to nematodes can be minimized. Of all the methods, however, regulatory measures like quarantine is more practical and effective in restricting the movement of nematode infected plant materials and contaminated soil into a state or country. Contaminated plant material should be treated (hot water or nematicides) to kill the plant parasitic nematodes before planting to prevent the further postharvest damage. These various measures are primarily aimed at either reduction or wiping out of stages of nematode from the site or protection of host from infection or creation of unfavorable host and/or environmental conditions for the nematodes.

Introduction

Therapeutic foods are products, which are multiutility food products that may be used as nutrition as well as medicine. A nutraceutical may be defined as a substance, which has physiological benefit or provides protection against chronic disease. Nutraceuticals are used to improve health, delay the aging process, prevent chronic diseases, increase life expectancy, or support the structure and/or function of the body. Oflate nutraceuticals are receiving considerable interest due to potential nutritional, safety and therapeutic effects. The examples of therapeutic foods are the foods used for feeding of malnourished children on an emergency basis or to supplement the diets of persons with special nutrition requirements, such as the elderly. Therapeutic foods can also form a part of treatment/prevention/reduction of other health conditions such as diabetes, cardiovascular disease, obesity, anaemia and any other lifestyle disorders.

The incidences of diet-related diseases are progressively increasing due to greater availability of calorie-rich foods and a sedentary lifestyle. Obesity, diabetes, atherosclerosis, and neurodegeneration are major diet-related diseases. Nutraceuticals and functional foods represent a novel therapeutic approach to prevent or attenuate diet-related diseases.

There is always a requirement for cheaper formulations using locally available ingredients that are processed in a safe, reliable, and financially sustainable methods. Some of the literature available on health foods for various diseases is summarized below. However, since the burden of diabetes in India is staggering. In 2017, 72 million cases of people suffering from diabetes were reported and the figures are expected to reach 134 million by 2025, this chapter more emphasis is given on the safe, natural treatment/reduction of diabetes by herbal means.

We get energy from food. We need energy for all the activities which we get by eating. The body structures as muscles, organs and bones are composed of the nutrients contained in food which are absorbed by the body.

Nutritional requirement of the major nutrients

Nutrients are the substances which are found in food and drive biological activity. They are essential for the human body. These are categorized into proteins, fats, carbohydrates (sugars, dietary fiber), vitamins and minerals (Sugishima, 2019). They perform the vital functions like building all parts of the body as muscle, bone, teeth and blood. Out of the 20 different kinds of amino acids that make up proteins nine are not synthesized in the body and are therefore called essential amino acids. These essential amino acids have to be supplemented through food. High-protein, low-carbohydrate diets have been found to be effective.Protein is an important component of every cell in the body. Large part of hair and nails are made up of proteins. The human body uses protein to build and repair the tissues, helps in making enzymes hormones and other body chemicals. Protein is an important building block of bones, muscles, cartilage, skin and blood.

1. INTRODUCTION

Amongst the common fermentations employed in food are alcoholic, lactic acid and acetic acid. Lactic acid fermentation is a potent tool of biopreservation of foods by the use of biological means i.e. microorganisms or their metabolites having antimicrobial action. It deals with the extension of storage life and increased safety of edible products by employing natural microflora or their antimicrobial products such as in food fermentation. Though many problems in food processing and microbiological safety of food have diminished, yet these are certainly not eliminated altogether. These include the likelihood of food-related illness and product spoilage in industrialized countries. The increasing consumption of pre-cooked food, prone to temperature abuse, are among the main causes of this scenario. The bacterial pathogens that account for many of these foodborne illness cases include Salmonella, Compylobacter jejuni, Escherichia coli 0157:H7, Listeria monocytogenes, Staphylococcus aureus, and Clostridium botulinum. Until now, approaches to seek improved food safety had relied heavily to find out more efficient chemical preservatives or on the application of more drastic physical treatments (e.g. high temperatures) of food processing. Nevertheless, these types of solutions do have some drawbacks also: the proven toxicity of some of the commonest used chemical preservatives (e.g. nitrites), the alteration of the sensory and nutritional properties of foods (thermal processing) especially recent consumer trends in purchasing and consumption, with demands for safe but minimally processed products without additives.

HISTORICAL DEVELOPMENTS

Food Preservation 1782 ó Canning of vinegar was introduced by a Swedish chemist.

1810 ó Preservation of food by canning was patented by Appert in France. ó Peter Durand was issued a British patent to preserve food in ìglass, pottery, tin or other metals or fit materials.î The patent was later acquired by Hall, Gamble, and Donkin, possibly from Appert.

Food is essential for human survival. It provides the required energy and vital nutrients for sustainable growth and development. With the increase in population and awareness, the demand for nutritious, fresh and healthy food also increases. Although adequate food is produced in order to meet the increased demands, it fails to reach the consumers in need due to food Food Storage and Preservation Practices   35 wastage and spoilage occurring during various stages of harvesting, food production, storage and transportation. Gajanana et al., (2009) stated that there is a mammoth wastage of food post-harvest. It is estimated that 20 to 60 % of produce are wasted during and after post-harvest. 

Food Plant Hygiene

A. I.mportance of Food Plant Hygiene:

1. Ensures the Safety and Quality of Food Products: Proper hygiene practices within food processing facilities play a critical role in safeguarding the safety and quality of food products. By adhering to stringent hygiene protocols, including thorough cleaning, sanitation, and preventive measures, facilities can effectively prevent the contamination of food products by harmful microorganisms, chemicals, or physical hazards. This helps minimize the risk of foodborne illnesses and ensures that consumers receive safe and wholesome food products. Additionally, maintaining cleanliness and hygiene in food proce

Plant hormone ethylene is involved in a number of physiological activities within the plant system, ranging from seed germination to fruit development. Ethylene acts as a key player in accelerating fruit ripening by regulating the activities of different enzymes, and is responsible for shortening the shelf life and associated post-harvest losses during the storage of fruit crops. However, all fruit crops have different ethylene production capacities and vary in their response to ethylene. Hence, effective management of post-harvest ethylene is imperative for addressing the global challenge of reducing fruit losses after harvesting. In recent periods, numerous technologies and compounds have been developed for the suppression of ethylene and for enhancing in-situ oxidation of ethylene or inhibiting its production at a receptor level. Among these emerging techniques, the use of sachets, fumigating agents, catalysis and composite films embedded with nanoparticles has been found to be trending, but the use of some of compounds has been limited due to health risks or consumer unacceptance. However, most of these technologies are very costly and are not affordable for marginal farmers and developing nations. In order to address these issues, long term breeding approaches for shelf-life improvement, targeting the tfs, ERFs have been involved. This manuscript fills the knowledge gap by encompassing all the recent progress made in enhancing the shelf life of fruits by managing ethylene during storage.

2.1. Introduction
The present century is the century of oxidative stress (OS) that linked to several life-threatening disorders which predominantly affect public health as well as their nutritional status. Unhealthy lifestyle and eating pattern which is major concern for OS. The biological literature first used the phrase “oxidative stress (OS)” in 1970. OS can be defined as a state of imbalance condition between the high level of pro-oxidants and the low level of antioxidant scavenging capacity in the body. The normal oxidative process that occurs in cells is crucial for the existence of life and favours the death of a cell. Free radicals, which are unstable, can form when molecular oxygen breaks up into pairs. This unstable radical has a high level of reactivity and produces reactive molecular species like reactive oxygen species (ROS) and reactive nitrogen species (RNS). To resist the OS and to maintain the redox balance, cells have an inbuilt antioxidant defence capacity, comprising of superoxide dismutase (SOD), catalase (CAT), and glutathione peroxidase (GPOD) etc. But some pathogenic or environmental conditions may overpower this antioxidant defence system, allowing a portion of reactive oxygen and nitrogen species (RONS) to bypass degradation and create much more reactive radicals. Increased ROS and RNS affect redox balance and damage DNA, proteins, amino acids, and fats, causing alteration of structures as well as action of cells and tissues. This will ultimately produce several pathogenetic elements associated with clinical situations and leads to the development of human aging and numerous diseases. Several dietary components such as whole grains, nuts, fruits, and vegetables are excellent sources of antioxidative vitamins, minerals, nutraceuticals or phytoceuticals that shields the human body from the harmful oxidative injury by scavenging or destruction of free radicals and also by upregulation of endogenous antioxidant defence system. Thereby long-term and sustainable OS remedies can be performed.

Revolutionizing skin cancer detection
The diagnostic process for skin cancer is evolving. Physicians have in the past relied upon physical exams to be followed by scanning and biopsies taking anywhere between 15 days to return results. Although most abnormalities turn out to be non-cancerous, this is distressing to patients and contributes to healthcare costs. Additionally, certain growths that turn out to be cancerous remain undiagnosed since they have not been visible.
Breakthrough startup Damae Medical is set to reverse this process. The startup has developed an advanced probe that is able to take 3D images of the skin to unveil the full extent of abnormalities in real time. This enables doctors to diagnose in an instant, enabling improved personalized treatment. When an operation is required only diseased tissue is removed to prevent unnecessary treatments and improved outcomes in patients.
The Origins in the Institut d’Optique
The beginnings of Damae Medical can be traced to Palaiseau-based Institut d’Optique where in 2013 two photonics students envisaged potential in an emerging imaging tech. Together with the inventor himself in 2014, they cofounded Damae Medical by taking an exclusive license to the core family of patents held by three partner institutions. While this contract was beneficial in launching the company to an early growth spurt, in the long run created difficulty in exercising control. This was resolved by taking an equity-forcontrol purchase in 2019 by Damae to acquire the foundational patent

C - enamel can : The sulphur resistant lacquer is golden coloured and the can coated with it are called C-enamel can or sulphure resistant can, used for packing non acid products.

CA storage : Storage of commodities under gaseous atmosphere like gas storage, where the composition of atmosphere is controlled accurately. MA and CA differ only in degree of control and CA is more exact. These storage methods in combination with refrigeration markedly enhance storage life of fruit and vegetables.

1.    Introduction
    
2.    Edible coatings used in Seafood Products
    2.1    Pre-dust
    2.2    Batter
    2.3    Breading
    
3.    The Coating Process
    3.1    Portioning
    3.2    Pre-dusting
    3.3    Application of batter
    3.4    Application of breading
    3.5    Pre-frying / Flash frying
    3.6    Freezing
    3.7    Packing and storage
    
4.    Coating Process Equipment
    4.1    Forming machine
    4.2    Pre-dusting machine
    4.3    Batter application equipment
    4.4    Breading application equipment
    4.5    Fryers
    4.6    Spiral freezers
    
5.    Coating Process Lines
    5.1     Single line breading system
    5.2     Tandem line breading system
    5.3     Tempura or batter-fry  Line breading system
    5.4     Tempura-Japanese Line breading system
    
6.    Coated Fishery Products
    6.1    Fish fingers
    6.2     Coated fish sillets
    6.3     Fish mince based coated products
    6.4     Coated shrimp products
    6.5     Coated squid products
    6.6     Coated bivalve products
    6.7     Crab claw balls
    
7.    Common Quality Problems Encountered during the Coating of Seafood
    7.1     Voids
    7.2     Blow off
    7.3     Pillowing
    7.4     Tailings
    
8.     Innovative Processes in the Production of Coated Products
    
References

Safe, wholesome and nutritious food is vital for sustenance, good health, food and nutritional security and augmentation of sustainable development of an individual. Also, safe food helps in the growth of the national economy and enhances the trade and tourism sector. Foods that are unsafe containing various kinds of microorganisms can cause chronic diseases or illnesses varying from diarrhea to cancer.

C - enamel can: The sulphur resistant lacquer is golden coloured and the can coated with it are called C-enamel can or sulphure resistant can, used for packing non acid products (Plate 81).

CA storage: Storage of commodities under gaseous atmosphere like gas storage, where the composition of atmosphere is controlled accurately. MA and CA differ only in degree of control and CA is more exact. These storage methods in combination with refrigeration markedly enhance storage life of fruit and vegetables (Plate 82).

CAC: It stands for Codex Alimentarious commission (1962). It is a joint commission of FAO and WHO, comprising of 146 member countries. It ensures consumer food safety, establish fair practices in food trade and promote the development of international food standards. CAC make standards for food additives, veterinary drugs, pesticide residue and other miscellaneous substances that affect consumer safety. These are published in Codex Alimentarius.

Cacao: The dried partly fermented fatty seeds of Theobroma cacao of the family Sterculiaceae that are used in making cocoa, chocolate, and cocoa butter called also cacao bean (Plate 83).

CAD: CAD (computer-aided design) is the use of computer-based software to aid in design processes. CAD software is frequently used by different types of engineers and designers. CAD software can be used to create two-dimensional (2-D) drawings or three-dimensional (3-D) models (Plate 84).

Abstract

Osmotic dehydration is gaining popularity due to several energy and product quality related advantages it offers. It has huge potential as a complementary process step prior to operations such as air-drying, microwave drying, freezing, frying etc, if not an alternative one, in the food process chain. It can be easily integrated with other processing steps in order to improve the overall efficiency of a given food process. Application of additional driving force either prior to or during osmotic dehydration can enhance the mass transfer rates in the osmotic dehydration. Role of mathematical modelling both in osmotic dehydration and rehydration have been discussed. Current limitations for the adaptation of osmotic dehydration in the food processing industry and possible solutions are also discussed in detail.

1. Introduction

 Mushrooms have been part of man’s diet for centuries (Rajarathnam and Shashirekha, 2003). Mushrooms grow on wide range of agro-residues, biodegrade and biotransform them into edible fruiting bodies (Rajarathnam and Zakia Bano, 1988a; 1988b; 1990; Zakia Bano and Rajarathnam, 1988; Zakia Bano et al., 1993; Rajarathnam et al., 1998). Their post-harvest life is very ephemeral at room temperature (Rajarathnam et al., 1983) due to delicate flavor (Rajarathnam et al., 1990) and high moisture content, with a range of chemical constituents (Zakia Bano and Rajarathnam, 1986; 1982; 1988; Rajarathnam and Zakia Bano, 1990; Rajarathnam et al., 1983; 1992). Since, they contain large quantities of water and therefore suffer considerable weight loss during transportation and storage, causes serious economic losses, due to reductions in weight and quality (Gray, 1970). When the supply of water, organic substances and minerals are cut off at harvest, the fresh mushroom enters a deterioration or perishable phase. Cap opening and stem elongation are the usual symptoms of senescence constituting visible evidence of deterioration. At room temperature, the shelf-life of mushrooms cannot be for more than 24 h (Rajarathnam et al., 1983). During this period, there are considerable changes in color, texture and taste. In addition, water is continuously being lost as a result of transpiration and respiration. Additional loss occurs from surface cracks and bruises that develop during growth and handling (Salunkhe et al, 1991). Fresh mushrooms are white or light buff, with no dark marks on either the cap or stem. The veil is closed and the gills are not visible. The upper surface of the caps should be strongly convex and stems should be plump rather than elongated. Mushrooms are grown on compost, usually in mushroom houses where the temperature and humidity can be controlled. Eventually after harvest, the mushrooms can never be able to withstand any increase in temperature and decrease in relative humidity. Mushrooms are commercially preferred at the immature stage characterized by closed caps, invisible lamellae, round stipe and light color. Agaricus development is classified into various stages (Table 1). Thus, the concept of physiology of fresh mushrooms being very complicated, bears a great impact on the delicate problem of extending the storage life. The various means and methods studied and adopted by various researchers to aim at extended storage life of fresh produce, underlined by its physical, chemical and biochemical properties and also development of value added products are critically evaluated.

1. Introduction

As dealt in earlier chapters, fruits and vegetables represent the most essential of horticultural component for acreage of production, yield, nutritional and nutraceutical values, of definite taste, texture, flavor and colour, involving defined health and medicinal benefits. Every year and over the course of every ten years, significant quantum of research data accumulates on the various facets of fruit and vegetable technologies, and also trends in production, processing and marketing, may also tend to change. At every stage, more thinking has gone to improve the technology, product quality and cost economics to suit wider markets, both domestic and foreign. It is a continuous endeavor to record newer and newer problems emerging and to set the strategies to solve them. Several relevant references, fitting to the various aspects representing the cross section of the fruit and vegetable technologies are dealt here, to conclude the subject and spell out the future.
Consumer demand for healthy convenience meals with ‘near fresh’ properties challenges researchers and industry to develop new or improved conservation procedures for processed products. Development of a dehydration process based on electromagnetic energy (EME) may bring about a major breakthrough with respect to retention of product quality and improved rehydration characteristics (Nijhuis et. al., 1996). Economic potential and current limitations of fruit and vegetable processing in India included improvements in preliminary treatment (harvesting, washing/cooling) precooling (including refrigerated transport/storage) and processing of juices and pulps. Establishment of a National Horticulture Board has aided to provide market information and so aid growers to get remunerative prices (Anon, 1993). The use of food irradiation as a quarantine method for treatment of food and agriculture commodities was organized by the joint Food and Agriculture Organization/International Atomic Energy Agency Division of Nuclear Techniques in Food and Agriculture, held in Kuala Lumpur, Malaysia, on 27-31 Aug., 1990. (FAO,1992). This has been experimented with various commodities, particularly for export trade of fruits like mango, as stipulated by the importing country like U.S.A.

Abstract

Application of ultrasound is one of the most promising uses of novel technologies in food processing. Use of ultrasound at various stages of drying has resulted in significant decrease in drying time and improvement in quality characteristics of dried products. The chapter discusses the principle behind use of ultrasound, general application in food industry with detailed description of various drying processes and equipments assisted by ultrasound.

1. INTRODUCTION

Harvesting is the process of gathering the crops from the fields at maturity. The harvesting of a commodity means the end of the growing season for a particular crop. Harvesting is the most labour-intensive activity of the growing season. Harvesting in general includes an immediate post-harvest handling, the actions taken immediately after removing the crop are pre-cooling, sorting, cleaning, packaging and up to the point of on-farm processing or shipping to the wholesaler or consumer.

Harvest timing is a critical decision that balances the likely weather conditions with the degree of crop maturity. Weather conditions such as frost, rain and unseasonably warm or cold periods can affect yield and quality. These conditions can be avoided by harvesting the commodities earlier than the harvest date, but this may result in poor yield and quality. On the other hand, delayed harvesting also results in a better yield, but increases the risk of weather problems. Thus, proper harvesting timings of horticultural commodities often play an important role.

Assessment of harvesting time is a critical time for growers of fruit and vegetables to decide the accurate period of crop harvesting. Fresh produce is normally ready for harvest when it has developed to the ideal condition for consumption and the condition is usually referred to as harvest maturity. Harvest maturity thus refers to the time when the “fruit” is ready to harvest and the time required to reach market. The harvesting should be done earlier than its ideal maturity for proper marketing.

Most growers decide harvesting time for different commodities by looking and sampling. Judgments are based on colour, size and shape (Sight); texture, hardness or softness (Touch); odour/aroma (Smell); sweetness, sourness, bitterness (Taste) etc. Experience is the best guide for this kind of assessment. Harvest maturity can readily be observed in some fruit crops but it can be more difficult in case of some fruits like avocados remain unripe off the tree after maturity.

1. Lecithin is an example of
   1. Carbohydrates
   2. Hormones
   3. Vitamins
   4. Phospholipids
2. Which of the following acts as storehouse of energy in body?
   1. Hormone
   2. Vitamins
   3. Fats
   4. All of these

1. The non-protein component in enzymes which is necessary for its biological activity is called
   1. Nucleic acid
   2. Lipids
   3. Phosphoric acid
   4. Coenzyme
2. The coenzymes are derived from
   1. Hormones
   2. Vitamins
   3. Lipids
   4. Carbohydrates

Introduction

Agricultural production is necessary to fulfil nutritional requirements for human populations and global food security. The agricultural sector also forms the economic backbone of many low-income countries in which millions of farmers are employed (Anushka et al, 2022). However, managing agricultural production to achieve multiple objectives of providing food, supporting livelihoods and protecting biodiversity and forests is a challenge especially in tropical, low-income countries (Anushka et al, 2022). Usually, the growth in global agricultural production is largely driven by commercial and export oriented commodities. One such agricultural commodity that has high global demand is cashew (Anacardium occidentale L.). Cashew is presently cultivated in 33 countries including India in the world. Global land area for cashew cultivation between 1980 and 2018 has seen an eleven-fold increase from 526,250 ha to 5,972,724 ha (Anushka et al, 2022).

Storage Systems

    1.    Low cost storage technology

        ·    In situ : Means delaying the harvest until the crop is required and employed 
    for the root crops.
        ·    Sand and Coir : Used for the Potatoes
        ·    Pits used for the Potatoes
        ·    Clamps used for the Potatoes
             Wind breaks used for the Onions – 6 months 1m height wooden stakes
        ·    Cellars : under ground / partly under ground. Ex: Apples, cabbage, 
    onions and potatoes during winter.
        ·    Barns : In Sudan onions are stored in palm leaf barns called “Rakubas”.
        ·    Evaporative Coolers
        ·    Zero energy cooling chambers
        ·    Night ventilation.

    2.    As a general rule, air circulation of storage room is designed to provide about 25m² / min / 3000 K cal of refrigeration predicated on a 5.5ºC

    3.    Frozen storage refers to storage at temperature where food is maintained in frozen conditions.

    4.    Good frozen storage generally means - 18ºC / below.

    5.    Below – 9.4ºC, there is no significant growth of microorganisms in food.

1. Tyson Foods Inc. 
2210 W. Oaklawn Drive, Springdale, AR 72762-6999 
Phone  : 479-290-4000; Fax  : 479-290-4061; Web site  : www.tyson.com

Executives : Chairman : John Tyson; Pres./CEO : Richard Bond; SVP-Intl. Ops. : Mike Baker; SVP-Commodity Trading & Risk Management : Jean Mrha Beach; Group VP-Research & Development, Logistics & Tech Services : Hal Carper; SVP & CIO : Gary Cooper; Group VP & International Pres. : Rick Greubel Jr.; SVP, Controller & CAO : Craig Hart; VP, Assoc. General Counsel & Secretary : R. Read Hudson; Group VP-Ops : Donnie King; SVP-Human Resources : Ken Kimbro; EVP & CFO : Dennis Leatherby; Group VP-Food Service : Bernard Leonard; Sr. Group VP-Fresh Meats : James Lochner; SVP-External Relations : Archie Shaffer III; Group VP-Consumer Prods : Donnie Smith; EVP & General Counsel : David Van Bebber; SVP-Renewable Products : Jeff Webster; VP-Investor Relations & Asst. Secretary : Ruth Ann Wisener

1. Introduction

 Banana is the developing world’s fourth most important food crop (after rice, wheat and maize) accounting for 70 million metric tons per annum (FAO stat, 2007 faostat.fao.org/site/567/Desktop Default.aspx?). Banana is also the second highest fruit crop in the world, representing a wide range of varieties of cooking and dessert types, providing a staple, nutritious inexpensive food for millions of people. The word “banana” is a general term embracing a number of species or hybrids in the genus Musa of the family Musaceae known simply as the banana family. Two Musa species namely Musa acuminata and Musa balbisiana, out of the 28 described were first noted in 1865 by Kurz as being the origin of most of the commercial clones (Stover and Simmonds 1987). Cultivated clones are parthenocarpic, mostly sterile with starchy fruits. Indeed, wild types are very fertile; their fruits are full of seeds with little starch, and are seldom fit for human consumption. Its abundance, varietal diversity, availability round-the-year and low cost make banana an important commodity for the religious occasions in many tropical countries. The vegetable bananas, generally grouped under ‘Plantains’ are larger, more angular than dessert type and are generally intended for cooking unripe, although ripened ones are quite like dissert bananas.

Introduction

Foods prepared by fermenting raw ingredients of plant or animal sources naturally or mixing it with the starter culture (s) containing functional micro flora is called fermented foods. The functional micro flora used in starter culture is responsible for biochemical and organoleptic alteration of the substrates into edible yields which are socially and culturally appropriate to consumers (Tamang et al., 2010a, Tamang et al., 2010b). Fermented food has its own characteristic microflora and this group of micro flora increases the nutritional value by increasing the levels of essential amino acids, vitamins, proteins, etc.

Fermented foods play a major role in meeting nutritional requirement and socio economic development of developing countries. They are important components of the diet as staples, adjuncts to staples, condiments and beverages. A wide variety of fermenting substrates are available such as cereals, pulses, soya beans, flowers, milk, fish, meat, etc. A wide majority of plants and their parts are often utilized in the preparation of starter culture (Deori et al., 2007, Deka and Sarma, 2010).

Pack inspection: It is similar to continuous inspection except that here inspector(s) may make in-process checks during different processing operations under contract but not required to be present all the times in the plant during operation.

Package: The package means a pre packed box, tin, barrel, pouch or can etc in which food article is packed.

Package store: A store that sells bottled or canned alcoholic beverages for consumption off the premises.

Packaging: Packaging is an industrial and marketing technique for containing, protecting, identifying and facilitating the sale and distribution of agricultural, industrial and consumer products (Plate 467). Packaging is defined as an enclosure of products, items or package in a wrapped pouch, bags, box, cup, bottle or any container form to perform one or more of the functions as containment, protection and preservation, communication and utility or performance. Technically, packaging is a system or method by which a product from the manufacturing point to the consumer level reaches in a safe and sound condition at an affordable cost. The primary purpose of the packaging is to protect the food product, to keep it in good condition and to preserve the flavour until it reaches the consumer. It is therefore, very essential that a suitable form of the packaging is chosen for a finished product. Packaging is an art, which determines the buying decision of a consumer. or Wrapping / placement of objects in paper / other packaging materials, keeping in box, etc is known as packaging which has two main functions, to assemble the produce / objects in convenient units for handling and to protect them during transporting, marketing and storage which results in extended shelf life of the produce. “Packaging” play a very important role not only in ensuring safety of the product during transportation, storage and distribution and in conveying information about the pack contents to the consumers, but also ensuring desired sensory characteristics and micro biological soundless till consumed.

Saccharification: The process of breaking a complex carbohydrate (starch or cellulose) into its monosaccharide components is called saccharification.

Saccharimeter: A device (polarimeter) used for measuring the amount of sugar in a solution is called saccharimeter. It is also known as saccharometer. It is a hydrometer with a special scale.

Saccharin: A crystalline compound C7 H5 NO3 S that is unrelated to the carbohydrates, is several hundred times sweeter than sucrose, and is used as a calorie free sweetener.

Saccharomyces: It is one of the genus (Saccharomyces) of the family Saccharomycetaceae and is usually unicellular yeasts (brewer’s yeast) that are distinguished by their sparse or absent mycelium and reproduced asexually by budding.

Safe food: Food that provide maximum nutrition and quality while revealing a minimal hazard to public health and they assume any risk present to be minimal.

8.1. Introduction
Micronutrients are vitamins, minerals, and nutraceuticals that do not provide energy and do not raise any sensation of hunger known as “hidden hunger” or “insensible hunger”. Hidden hunger that causes micronutrient deficiency affects 2 billion people globally. Due to the deficiency of micronutrients, different diseases are noted among public health professionals that reflect poor community nutrition. To overcome these deficiency-related diseases, one of the important approaches is food fortification. Food fortification is a public health policy to reduce the number of individuals, who suffer from micronutrient deficiencies within a population. Common examples include iodine-tagged common salt, vitamin A-containing oil, and iron-enriched rice all of which are examples of food fortification. In the agricultural field, food fortification (FF) and/or food enrichment (FE) is the most efficient strategy to overcome various micronutrient deficiencies by the addition of essential micronutrients (vitamins and minerals) to enhance the nutritional value of cultivated crops. According to World Health Organization (WHO) and Food and Agricultural Organization (FAO) of the United Nations (UN), “Food fortification” is defined as “the practice of deliberately increasing the content of an essential micronutrient, i.e., vitamins and minerals (including trace elements) in a food irrespective of whether the nutrients were originally in the food before processing or not, so as to improve the nutritional quality of the food supply and to provide a public health benefit with minimum risk to health” (Pant and Chinwan, 2014). “Fortificant” refers to the incorporation of substances in the food to provide micronutrients. “Micronutrients” refers to the important dietary components, including vitamins and minerals, that are required in very small amounts but are engaged in very critical roles in various body functions and disease prevention.

INTRODUCTION

Preservation of food by drying or chemical means as by alcohol or acid fermentation and that by the use of ice is long recorded in history. With the advancement of science and the knowledge governing various unit operations in food processing, these food preservation techniques employing thermal, radiation, or low temperature or a combination of these have only got further refined as regards their viability and commercial applications. Process foods of different genre and cuisine, which include frozen foods too, are increasingly becoming popular the world over for reasons of quality, safety and year round supply of nutritious foods to cater to different niche segments of human society. Increasing health consciousness is buoying those processed foods which are preserved and stabilized using non-thermal technologies as these ensure retention of food nutrients to a better definition. Interest in frozen food also stems from need to deliver safe and nutritious foods with extended shelf-lives.

1.1 Introduction and Background

In present scenario, the word “extrusion” refers to a process by which dry or semi-moist ingredients with varying in-barrel moisture are forced through varying barrel temperature, screw speed and screw configuration through a die opening of the desired cross section. In other words, extrusion is predominantly a thermo-mechanical processing operation that combines several unit operations, including mixing, coating, kneading, venting, shearing, heating, forming, partial drying or puffing, depending on the material and equipment used.

The origins of extrusion are in the metallurgical industry, where in 1797 Joseph Bramah patented the first extrusion process, wherein a piston driven device was used for making seamless lead pipes. The present understanding of extrusion technology and the developments or improvements in machine design are largely due to research carried out by the plastics industry. In food industry, this technology is in use since 1930 and its popularity is increasing continuously due to its efficiency, continuity and sustainability. In beginning, sausage extruders were developed in the nineteenth century as simple forming machines. One of the original developments which laid the foundation of the food extrusion was the use of pasta press termed as “cold extruder” in mid 1930s. Furthermore, in the late 1930s, General Mills, Incorporation., Minneapolis, MN, USA, first used a single screw extruder in the manufacture of ready-to-eat (RTE) cereals. Later in 1970s, twin screw extruders were used for the manufacture of moist pet-foods. Twin screw extruders were also adapted from polymer industry, as rising food quality and limitations of single screw extruders were demanding a more versatile process for the newer and higher quality products. After 1970s, the extrusion processing with simultaneous use of heat was popularized as a versatile and highly energy efficient with negligible wastage process. In all these years, number of changes has been noted in the extruder design such as changes in screw design, barrel design and also material used for the manufacture of these materials. Barrel liners availability along with already available segmented screws could further add more economics to the process and increased equipment lifetime. For better wearing characteristics, a number of screw elements of different materials are being used in addition to standard nitrided steel for customized processing needs, such as corrosion and wear resistant surface coated steels, stainless steel, satellite welded and bimetallic HIP (Hot Isostatic Press). JBL Feedscrews Limited, a UK based company recently introduced tungsten carbide coated screw in conjunction with a compatible bimetallic barrel. Likewise, a number of options for barrel metallurgy are available to withstand the higher internal pressure and temperature. Barrels lined with hard cobalt based alloy, typically Xaloy, to give abrasion and chemical resistance are also in use, although, the most common material is carbon steel with a nitride interior. Similarly, steam heated or jacketed barrels were used earlier for cooking purpose which gradually replaced by the electric induction heating elements. These HTST cooking extruders are versatile, highly productive and energy efficient processing machines. They can use a wide variety of raw materials and formulations to produce products with increased shelf-life and convenience.

6.1 Introduction

Consumer demand, regulatory guidelines and economic power of the consumer as well as ascertained profitability stimulated the need of novel food processing techniques. The concept of “fresh”, “natural”, or “organic” food also led to the development of environmentally sound and resource efficient food processing technologies. Thermal processes have been used for food preservation since a long time. These are not very energy efficient and can change the phase of food from fresh to cooked as well as it can alter the nutritional and sensory qualities. Thus, the quest for energy conservation by the manufacturers to reduce carbon footprint of the processes involved in food processing and preservation as well as to fulfill consumers’ requirement for fresh-like quality food have given rise to the development of innovative non-thermal food processing technologies i.e. ionizing radiation, high-intensity light pulses, high isobaric pressure, electric or oscillating magnetic fields, as well as pulsed electric fields (PEF).

Application of electric energy in food processing started in the early 1900s. In the beginning, electrical pasteurization inactivated microorganisms by increasing the temperature of samples by means of an electrical resistance (ohmic heating). Milk was the first electrically pasteurized product. In the late 1940s, electric fields were used to increase the permeability of fruits to facilitate the subsequent extraction of juices. The PEF technology as a non-thermal process is very effective for inactivation of microorganisms, increasing the pressing efficiency, enhancing the juice extraction, and for intensification of the food dehydration and drying process. The main effect of PEF technology is based on the phenomena that biological membranes are punctured under the influence of external electrical impulses. This process is often referred as non-thermal, since the structural damage to membranes is implemented at very low temperature compared to the conventional heating process. The PEF process is considered to be energy efficient because the electric energy is released in short pulses, thus total energy requirement is much lower than other continuous preservation technologies. The microbial inactivation can be achieved at ambient or moderately elevated temperatures by the application of short-bursts of high intensity electric fields to liquid foods flowing between two electrodes or to semi-solid/ solid food between some specialized electrode and treatment systems. Due to chemical/physical properties and presence of electrical charge, the liquid foods (e.g. milk or fruit juices) had different conductivity, which results in variable flux of electrical current through the food systems.

1. INTRODUCTION

India is a vast country having a geographical area of 328 million hectares with 15 distinct agro-climatic zones. Fruits and vegetables are one of the most important and fast growing sub-sectors as they form an indispensable part of healthy diet. It holds a unique position for growing a wide range of vegetables in its diverse agro-climatic conditions. World production of vegetables amounts to 486 million tons, while that of fruits is 392 million tons. India produces 159.5m MT tons of vegetables from an area of 9.07 million hectare annually (NHB, 2013). Productivity of vegetables in India presently is 16.7 tons per hectare. India produces 36 % green peas and 10% onion of world’s production. Onion, potatoes and green vegetables like okra, bitter gourd and green chillies also have good export potential. Being rich in vitamins, minerals, dietary fibre and natural antioxidants most vegetables are classified as the protective foods. However, owing to the presence of high moisture content and mostly being non acidic, the vegetables are highly perishable and needs to be handled properly and immediately after harvest. Processing of vegetables into different value added products is one of the most effective alternatives to reduce post harvest losses.

Vegetables are highly beneficial for the maintenance of health and disease prevention. An intake of about 280 grams of vegetables per day per person has been considered essential. Vegetable unlike cereals deteriorated quickly when stored for long periods because of the relatively high moisture contents. Huge amounts of losses take place between harvesting and consumption. Various causes are attributed to the deterioration process and it becomes essential to adopt integrated, low cost system of post harvest technology right from the pre-harvest stage.

Introduction

As the world population continues to grow, the global market for food products is expanding, together with an increased emphasis on food safety. Consumers have become more discerning in the type of foods they buy and how these foods affect their health and well being. Food safety is generally defined as the assurance that the food will not cause any harm to the consumer when it is prepared and/or eaten according to its intended use ( To achieve food safety, a management system has been developed which aims on preventing problems before they occur, rather than trying to detect failures through end product testing. It also places more responsibility for ensuring food safety on food manufacturers, who have to develop control and traceability of their products from ‘farm to plate’. The system requires the identification of specific hazards throughout the entire process of food production, concentrates on the points in the process that are critical to the safety of the product, and highlights measures for their control (Henson and Caswell, 1999).

Food waste and loss is an enormous issue worldwide. The FAO states that ‘Hunger is still one of the most urgent development challenges, yet the world is producing more than enough food’, but a vast amount of what is produced gets lost on its way from the field to the consumer. According to the FAO, about 30% of cereals, 20% of dairy products, 35% of fish and seafood, 45% of fruits and vegetables, 20% of meat, 20% of oilseed and pulses and 45% of roots and tubers are lost or wasted. Postharvest food loss is defined as measurable qualitative and quantitative food loss along the supply chain, starting at the time of harvest till its consumption or other end uses. Food losses can either be the result of a direct quantitative loss, for example, during the process of harvest or transport or arise indirectly due to losses in crop quality such as undesired sprouting or water loss. Postharvest food loss consists of many factors, which have not changed much in the last 40 years and so postharvest food loss in general has not changed much. Figure 1 illustrates the main reasons for food loss along the supply chain and is based on ‘The food pipeline’ published by Bourne in 1977. Food loss is highest during storage due to pathogens (insects, bacteria and moulds), environmental conditions (e.g. rain, humidity, heat and frost), sprouting and quality loss (rancidity, water loss and saccharification) or animals (rodents and birds). Recently published data for Switzerland have shown that about 53%-55% of the initial fresh potato production and 41%-46% of the initial processing potato production are lost mostly due to pathogen infection, saccharification, water loss of tubers and early sprouting during storage (Buchholz et al, 2018).

1. INTRODUCTION

Flavour is a distinctive property of a substance affecting the gustatory sense. It may be defined as “The sum of those characteristics of any material taken in the mouth, perceived principally by the senses of taste and smell, and interpreted by the brain.” Flavour perception is a complex process which requires the particles to be mixed with saliva and salivary enzymes to promote the release of flavour. Flavour molecules are very diverse in nature. More than 5000 compounds in food have been identified as flavour components which can be detected at very low concentration and are thus, used in products at very low levels. Hexenols and hexenals, characteristic of green taste of fresh fruits and vegetables, can be perceived at a concentration of about 1 part per million (ppm). Naturally occuring flavour compounds are present at a very low concentration ranging from parts per trillions (ppt) to parts per millions (ppm) level. Majority of these compounds are volatile, with boiling points in the range of 20-300 °C. Most of these compounds are lipophilic and possess a great diversity of chemical group and structure with molecular weight ranging between 50-250 g/mol.

Flavour and fragrance compounds are a part of expanding industry with an estimated cost of nearly $27 billion. These comprise of diverse molecules with unique structures and functional groups that contribute to varied aroma and flavour, ranging from floral to fruity notes. The processing operations modify the equilibrium between the different components in raw food that might weaken the original flavour, which require subsequent supplementation. These flavour supplements can be natural or chemically synthesized. Of all the available flavour compounds, around 80% are produced by chemical synthesis whose use is limited due to formation of racemic mixtures and lack of substrate specificity. The growing awareness of consumers towards chemicals supplemented to food has led to the development of the flavouring compounds of biological origin referred to as natural flavours or bioflavours. The first major source of flavour compounds was primarily from plants. Identification of microbes producing vital food flavourants paved the way for alternative low cost, efficient and flexible method for the commercial production of flavour compounds.

C - enamel can: The sulphur resistant lacquer is golden coloured and the can coated with it are called C-enamel can or sulphure resistant can, used for packing non acid products (Plate 143).

CA storage: Storage of commodities under gaseous atmosphere like gas storage, where the composition of atmosphere is controlled accurately. MA and CA differ only in degree of control and CA is more exact. These storage methods in combination with refrigeration markedly enhance storage life of fruit and vegetables (Plate 144).

CAC: It stands for Codex Alimentarious commission (1962). It is a joint commission of FAO and WHO, comprising of 146 member countries. It ensures consumer food safety, establish fair practices in food trade and promote the development of international food standards. CAC make standards for food additives, veterinary drugs, pesticide residue and other miscellaneous substances that affect consumer safety. These are published in Codex Alimentarius.

Amino acids are essential components of all living cells as building blocks of proteins. They are also metabolically active and supply substrates for many other biochemical reactions. In a bacterial cell, about 0.4% of the dry weight is amino acids. The amino units in other living systems varies according to species, age and part of the body.

15.1 Introduction

Color of food is the most sensitive part of any commodity as it is the one of the organoleptic characteristic to be noticed and one of the main ways of visually assessing a food before it is consumed. The people associate certain colors with certain flavors and the color of food can influence the perceived flavor in anything from confectionary to beverages. For this reason, food manufacturers add dyes to their products. Sometimes the aim is to simulate a color that is perceived by the consumer as natural, such as adding red coloring to glace cherries, but sometimes it is for effect, like the green ketchup that was launched by Heinz in 2000. If the flavor of a food product is inconsistent with the color, the flavor can often be perceived incorrectly, for example an orange flavored drink colored green could be perceived to taste of lime. In addition, the color of a food substance is important indicator of its freshness. While all of us are aware that food with bright or unnatural colors likely contains food coloring but only few people know that natural foods such as oranges and salmon are sometimes also dyed to mask natural variations in color. The color variation in foods throughout the seasons and the effects of processing and storage often make color addition commercially advantageous to maintain the color expected or preferred by the consumer. Some of the primary reasons include: