eChapters

1. Introduction

Nursery is a place, where seedlings and saplings of different ornamental plants (trees, shrubs, climbers, annuals, potted plants etc.) are propagated and maintained until they are out-planted in a prepared bed or in pots. Establishment of an ornamental nursery is emerging as a profitable venture, especially around cities. Rapid urbanization has led to the development of community parks and various sites for people to engage in active and passive recreation. This has led to surge in demand for quality planting material, which ensures rapid establishment and beautification of the landscape site. The following chapter deals with the basic principles and practices of establishment of ornamental plant nursery, with reference to its effective management to enhance the income and reap better profit.

1. Introduction

Nursery raising is as old as agriculture and has many advantages compared to direct seeding in special situations like vegetable cultivation and other high value plants. There are several types of nurseries to cater different crop species like ornamental plants, fruit plants, forest plants and vegetables, although the fundamental concept of all these nurseries is the same. With the advent of drip system, soilless media and plasticulture the nursery system has also become more modern and automated. A nursery is a area or place for growing and looking after young seedlings/plants until they are ready for planting in the main field. 

1. Introduction

Global population is expected to reach 9.7 billion by 2050 (UN report, 2019) and food requirement will betwofold of the current levels to feed the growing population. Asia and the Pacific regionaccounts for> 70% of the global population but has only 30% of the world’s arable land (FAO, 2021). An increase in yield of these regions over the years has largely been due to excessive and indiscriminate use of inputs like irrigation, seeds, fertilizers, pesticides, agrochemicals etc. and at considerable expense of its natural resources. Most of the pesticide recommendations are also region specific, which are on a few random observations of pest density. Because of low quality of agrochemicals often due to adulteration and increased pest resistance, indiscriminate application is now common especially in high valued crops.

1. Introduction

Zinc is an important micro-nutrient for human population and its deficiency can cause major diseases, mortality and thus becomes a major challenge in public health care systems of the developing nations. It was estimated that a major part of population is affected with deficiency of zinc (Combs, 2001) which causes lower growth, abnormal or decrease in infant birth, lowers the energy of body, decreases the power to lower the deadly infections, increase the mortality rate in children etc. (Gibson 2012; Krebs et al., 2014). Zinc also catalyzes various enzymes such as RNA polymerase, superoxidase dismutase and helps in working efficiency of cellular proteins. 

1. Introduction

Total population of India is estimated to cross 1.64 billion in 2050. Increasing population, decreasing economic status of Farmer, improper diet and nutrition, fixed farm land, degradation of cultivable land and malnutrition in Indian population is major key problem in 2 to 3 decades. More than 600000 children below 5 year age die due to improper nutrition each year in developing countries (White and Broadley, 1998). All the data provide a scary image about future. Almost 60% of the malnutrition children are iron deficient. Iron deficiency is very common among the girls; 30% each are deficient in zinc and iodine. The incomplete diet and malnutrition can lead to several disorder and degrade the human health (Shuman, 1998).

Agriculture University Kota, Jhalrapatan, Rajasthan, India

1. Introduction

India’s population is likely to reach 1.7 billion by 2050, making it as the thickly populated nation in the world. To feed the ever rising population, food production need augment by 70%. This augment is very serious since Indian agriculture is facing numerous challenges due to disintegration of holdings, ill brunt of climate change, sustaining investment, soaring fluctuation in prices and production, unorganized markets, inconsistent market performance, renovation of agricultural land intended for non-farm purposes and enlarged cost of production (Gangaiah, 2018). The current conditions of the Indian agriculture sector reflect that the farmers are facing severe deficit of income which is to an imperative issue and as a result dissuading the rural youth to take up agriculture as livelihood operation.

1. Introduction

There are around six hundred major and minor crop species but only two percent are cultivated commercially meeting the food (calorie) requirements. The most commonly cultivated food plants are even smaller counting to merely 20 crops (Wilkes, 1984). The huge number of underutilized crops may serve as potential fruit crops to meet the nutritional requirements of poor farming households in lesser common farming and subsistence agriculture. The adoption of underutilized crops on a commercial scale may not be possible without crop improvement, standardized agronomic and fertilizer management technologies, pre- and post-harvesting techniques and marketing (Bag Mal et al., 1997).

1. Introduction

Coriander (Coriandrum sativum L.) is a popular seed spice crop, used for dual purpose seed and leaves both. Since ancient times, coriander leaves have been used in the production of many popular Asian and East European foods. It improves the taste and flavor of vegetable, chicken, fish, and meat dishes when combined with other kitchen herbs and spices. Blending of green coriander leaves with other spice crops is used to make chatni (paste) which is a good appetizer, flavour enhancer and rich source of medicinal properties of coriander. The green leaves of coriander are a rich source of minerals like calcium, phosphorus and iron as well as vitamin A, C, riboflavin and folic acid. Coriander is one of the few plants which can be termed both as herb and spice, the seeds being used as spices (coriander) and leaves are widely used as herbs (cilantro). The green leaves of this herb contain 160 mg/100 g vitamin C, 12 mg/100 g vitamin A and 87.9% moisture, 3.3% protein, 0.6% fat, 6.5% carbohydrates and 1.7% mineral matter

1. Introduction

Spices are a high-value, low-volume commodity traded around the world. Spices have played a significant part in civilisation, exploration, and commerce throughout history. Since ancient times, India has been known as the spice capital of the world, with over a hundred different types of spices grown. India has long been a traditional producer, consumer, and exporter of spices, with nearly every state producing one or more of them. India has a total area under spice production of 39,27,430 ha, which produced 95,99,900 MT in 2017-18. (Spices Board, 2020a). Due to their rich aroma, texture, and flavour, Indian spices are in high demand around the world.

1. Introduction

Karonda is widespread throughout India, primarily in arid and semi-arid regions. As a hedge plant, the Karonda tree is frequently grown in residential gardens, farmer’s fields, and orchards. Karonda is widely used as a condiment or ingredient to Indian pickle and spices. It is a commonly growing indigenous shrub in India that may thrive in marginal and wasteland areas where other commercially important crops are unsuited. Karonda fruits are used in processed goods like as jam, jelly, squash, syrup, and chutney, and they are in high demand on the international market. Karonda is a rich source of nutrition and have highest Iron. The karonda fruits also contain vitamin C and it has antiscorbutic properties and helps to cure anaemia (Table 1). The fruits of Karonda are also used in many ayurvedic formulations. Root extract is used to reduce Chest pain.

1. Introduction

Chrysanthemum is commonly known as ‘Guldaoudi’, “Queen of the East”, “Glory of East” or “Autumn Queen”. It is one of the most beautiful and widely cultivated flowers that can be grown for its aesthetic value as well as for its commercial potential. The word chrysanthemum is derived from two Greek words, viz. “Chrysos” means gold and “Anthemon” means ‘flower’ i.e. golden flower. Chrysanthemum is the only crop that offers a great genetic diversity of flower colour, shape, forms, size, easy to propagate, growing habit, longer flowering duration and excellent vase life. Based on the shape of flower heads and floret arrangement of petals it can be used as pot plants for indoors and outdoors decoration as well as exhibition purpose; as cut flowers for flower arrangements, bouquets making and vase decoration; loose flower for making garlands, worshipping purpose and for bedding and garden decoration. Tall cultivars are suitable for background planting in borders and the dwarf and compact can be planted in front rows. 

1. Introduction

Cumin (Cuminum cyminum L.) crop belongs to the family Apiaceae and having diploid chromosome number 2n =14. It is also known as Jeera in Hindi. This crop is originated from Mediterranean region. It is an erect or sub erect, glabrous annual herb which grows to a height of 30-50cm. The leaves are alternate, compound and green, the blade consists of three slender filiform leaflets. The inflorescence is a compound umbel with white or pinkish flowers (Verma et al., 2018a). The typical pleasant aroma of the seeds is due to their essential oil and the main constituent in essential oil is cuminaldehyde. It is mainly cultivated in arid and semi arid parts of Gujarat and Rajasthan. The total area is about 12 lakh hectare with the production of about 8.5 lakh tons and total export of cumin is worth of more than Rs. 4200 crore during 2020-21 (Fig. 1 & 2). 

1. Introduction

Tuber crops are important group of crop species which produce tubers that are used for human food and animal feed. The popular tuber crops include cassava, sweet potato, greater yam, white yam, lesser yam, taro, tannia, elephant foot yam, yam bean, coleus etc. They contribute substantial amount of cheap energy coupled with high quality nutrition for more than two million people living in developing countries. Taro is one of the oldest cultivated tuber crop grown for its edible corms and leaves. It is an important tropical tuber crop, used as a staple food or subsistence food by millions of people in the developing countries in Asia, Africa and Central America. 

After independence, the Government of India realized the need of diversification in agriculture during the mid-eighties with an objective to make it more profitable through efficient land use. Due to diverse agro-climatic conditions, rich diversity in genetic resources of horticultural crops, sincere efforts through education and research, implementation of standardized technology by horticulturist in the field has achieved not only the production, productivity and export of horticultural produce but also the food and nutritional security. Such horticulture development in India is proudly said as “Golden Revolution”. Horticulture is also said to be a sunrise industry as it has potential to raise farm income, provide livelihood security and earn foreign exchange through export.

The horticulture industry is now expanding in many commercial sectors such as cultivation, production, post-harvest handling, processing, marketing, etc. Horticulture crops are grown on an area of 10% of India’s gross cropped area, as compared to over 50% of the area under food grains production. 

Indian Council of Agricultural Research; formerly known as Imperial Council of Agricultural Research, established on 16^th July 1929 and located at New Delhi. It is an autonomous organization under Department of Agricultural Research and Education (DARE), Ministry of Agriculture and Farmers Welfare, Government of India. It is the apex body for coordinating, guiding and managing research and education in agriculture including horticulture, fisheries and animal sciences. This is one of the largest national agricultural systems in the world.

The ICAR has played a pioneering role in ushering in the green revolution and subsequent developments in agriculture through its research and technology development. Thus, the food grains production increased by 5.6 times, horticultural crops by 10.5 times, fish by 16.8 times, milk by 10.4 times and eggs by 52.9 times to achievenational food and nutritional security during the period of 66 years (1950-51 to 2017-18). It has also played a major role in promoting excellence in higher education in agriculture. Organizational setup of ICAR to achieve mandate is as follows.

Many horticulture schemes have been launched by the Government. The main aim is to expand the area under horticulture with better productivity. These ambitious schemes are as follows.

A. Mission for Integrated Development of Horticulture (MIDH): Mission for Integrated Development of Horticulture (MIDH) is a centrally sponsored scheme from 1st April 2014 for the holistic growth of the horticulture sector covering fruits, vegetables, root and tuber crops, mushrooms, spices, flowers, aromatic plants, coconut, cashew, cocoa and bamboo. Under MIDH, Government of India (GOI) contributes 60% of total outlay for developmental programmes in all the states except states in North East and Himalayas, 40% share is contributed by state governments.

Intellectual property (IP) means a brand, invention, design or other kind of creation.Intellectual property contains an author’s copyright on a book or article, a distinctive logo design of any product or web site, patent regarding the process of manufacturing.However, Intellectual Property Rights (IPR) can be defined as legal rights given to people over the creation of their minds or intellectual activity in industrial, scientific, literary and artistic fields. Creator gets an exclusive right for a certain period of time to use his/her creations.Creations of the mind means inventions, literary and artistic works and symbols, names, images, and designs used in commerce. Intellectual property laws vary from jurisdiction to jurisdiction, such that the acquisition, registration or enforcement of IP rights must be pursued or obtained separately in each territory of interest.

The term biodiversity is abbreviated from two different terms ‘biological’ and ‘diversity’. Biodiversity is also called biological diversity. The term biological diversity was first coined by wildlife scientist and conservationist Raymond F. Dasmann in 1968. The same term i.e. natural heritage was used in the United State. Geneticists describe it as the diversity of genes and organisms. Biologists define biodiversity as the sum of genes, species and ecosystems of a region.

Biodiversity is determined by the wholesome number of different species in a particular area. It helps to strengthen the stability of an ecosystem and leads to a healthy biosphere. Existence of biodiversity is crucial for the functioning of the ecosystem and is the foundation of life on earth as it generates products and services for the existence of all living organisms on the earth.

India has experienced rapid urbanization as well as industrialization since independence. Though, the country has achieved considerable progress in industrial growth as well as expansion of urban and town spread, the land available in urban periphery as well as near big rivers are being utilized for non agriculture purposes. Similarly, for the development of road, rail as well as irrigation infrastructure, the government reserved huge land, which was under cultivation of various crops. The non agricultural businesses became more remunerative near cities and has increased the value of land near cities; which is not affordable for agriculture production. Considering the limitation of land for production purposes in urban areas, the concept of Urban Horticulture was conceived.

Crops that are not part of the customary diet of the local population and grown primarily for their high cash values and export potential are categorized as non- traditional. Non-traditional crops are usually cultivated on low acreage, crops such as ethnic fruits and vegetables, culinary and medicinal herbs, plants for industrial uses etc. are usually considered as non-traditional fruit crops. A non traditional crop may be new to a region or simply new to the grower. Many times non-traditional crops are cultivated to adapt to changing trends in agriculture and demographics.

For growing non-traditional crop proper planning is required to build a comprehensive business case. Realistic assessment of the potential risks and gains is necessary before actual implementation. All aspects of non-traditional crop production, including the agronomics of growing the crop, potential food safety and regulatory issues and marketing needs to be reviewed. Experience of producing conventional crops may not necessarily be directly applicable in producing non-traditional crops.

India has a wide agroclimatic range i.e. temperate, subtropical and tropical, enabling to achieve horticulture diversification. India is second in fruit and vegetable production at global level. The percentage share of horticulture output in agriculture has become 33%, (Horti statistics, 2018). However, productivity in most of the horticulture commodities is very low below world productivity, as we have not concentrated intensively on some major aspects to achieve competitiveness in horticulture for expansion in international trade.

India has potential to lead the world in horticulture. Horticulture is mostly concerned in different aspects of human beings such as provision of nutritious food to achieve a balanced diet; rural employment, integral part of rainfed and dry land areas, wealth generation through the activities of production, processing, marketing, servicing, and related sectors, economically important in export related activities and associated with all the elements of the supply chain etc. 

Precision farming is an approach, where inputs are utilized precisely to get increased average yields as compared to traditional cultivation techniques. Precision farming aims to improve crop performance as well as environmental safety. In other words, precision farming is the matching of resource application and agronomic practices with soil attributes and crop requirements as they vary across the field. Precision farming can improve both yield and profits by using optimum resources, while at the same time making agriculture more sustainable and less polluting. Sustainable precision farming is the most valuable innovation in farm management that is based on using Information and Communication Technologies (ICTs). This is the most recent innovation technology based on sustainable agriculture and healthy food production. Popular definition of Precision Agriculture (PA), Satellite Farming or Site Specific Crop Management (SSCM) describe the term as ‘a technology enabled approach to farming management that observes, measures, and analyzes the needs of individual fields and crops’.

India has an opportunity to grow a variety of horticultural crops due to varied agro climatic conditions and thus, it forms a significant role in total agricultural produce. Though, horticultural crops occupy 8% of the cropped area, approximately 30% contribution in agricultural GDP. Horticultural crops play a unique role in India’s economy by improving the income of the rural people.

However, during the last decades onwards, the productivity of horticultural crops has been affected by many factors. One of the major reasons is climate change. Climate change is one of the most leading environmental problems which is facing the modern world and directly or ultimately to human action that changes the arrangement of the global atmosphere.

The earth climate has always changed in response to changes in the cryosphere, hydrosphere, biosphere and other atmospheric and interacting factors. It is widely accepted that human activities are now increasingly influencing changes in the global cliamte. Emission of increasing amounts of greenhouse gases, carbon dioxide, methane, chlorofluorocarbons and nitrous oxide are responsible for generating changes to global climate. These changes are responsible for rise in sea level, rainfall sequences and movement of climatic regions due to increased temperatures.

Air pollution is the major environmental problem due to rapid urbanization and industrialization. It has led to continuous deterioration of air quality in both developed and developing countries.

Air pollution is characterized by high concentrations of suspended particulate matter, oxides of sulphur and nitrogen. Air pollution has long term effects on fruit trees; when exposed to higher orabnormal levels of various air pollutants. The injury symptoms range from visible marks on foliage, reduced growth and yield to premature death of the plant. The development and severity of injury depends not only on the concentration of the particular pollutant, but also on a number of other supporting factors. These include the duration of exposure to the pollutant, the plant species and development stage as well as conducive environmental factors.

Air pollution problems: Air pollutants are injurious to vegetation can generally be classified as either local or widespread.

Adverse climatic conditions like temperature, humidity, frost etc. affect vegetative growth, flowering, fruiting as well as quality of horticultural crops. Tropical crops are usually more sensitive to low temperature and frost injuries whereas temperate crops are vulnerable to high temperature effects. High temperature beyond tolerable limits may cause sunscald, tip dieback, bud death and heartwood damage. On the other hand, when temperature drops below the freezing point; water molecules ice formation in the intercellular spaces takes place showing freezing injuries on various plant parts. The symptoms like dehydration and necrosis are visible on plant due to increased concentration of sugars within the cell causing reduction in the water content. The extent of damage will depend upon the prevailing low temperature and its duration. Exposure of the plant near freezing temperature for prolonged time causes death of the plant due to formation of ice crystals in intercellular spaces.

It is difficult to define ‘stress’ precisely. In engineering and the physical sciences, it is usually defined as the force applied per unit area. But as far as in biology, stress it is usually described more loosely as any factor that disturbs normal functioning of an organism. Any environmental factor potentially unfavorable to plant is termed as stress.

The effect of stress on plant condition is called strain. Stress is the action, whereas strain is the reaction. Stress may be defined as external conditions that adversely affect growth, development and productivity. Stress may further classified as:

• Zero stress: This is the level of exposure of plants to environmental factors that leads to neither injury nor reduction in growth and yield of crops.
• Stress escape: Capacity of the plant to complete its life cycle during wet season before onset of stress.

In India, some of the major horticultural crops productivity is affected by major problems. Some of these have been overcomed by certain control measures strategies. However, a few of them are long lasting and have attained the status of national problems. These are mango malformation, alternate/biennial bearing, spongy tissue in mango, bunchy top of banana, guava wilt, citrus decline, rootwilt of coconut and yellow leaf disease of arecanut.

Mango malformation: Mango malformation was reported for the first time from Darbhanga, Bihar. The disease is more prevalent in northwest than northeast and south India. This disorder is widespread in flowers and vegetative shoots.Three types of symptoms are mainly observed. These are bunchy top phase, floral malformation and vegetative malformation. Bunchy top phase is observed in nursery, bunching of thickened small shoots, bearing small rudimental leaves. Shoots remain short and stunted giving a bunchy top appearance. In vegetative malformation, excessive vegetative branches of limited growth are observed in seedlings. 

oilless culture is a method of growing plants without soil. It is an artificial means of providing plants with support and a reservoir for nutrients and water. The simplest and oldest method for soilless culture is water culture or solution culture, where inorganic chemicals are dissolved in a vessel containing water to supply all the nutrients to plants. This method was originally termed hydroponics (water working) by W.F. Gericke in the 1930s. Over the years, hydroponics has been used sporadically throughout the world as a commercial means of growing both food and ornamental plants. Today, it is used widely in research facilities as a technique for studying plant nutrition.

Gravel or sand is sometimes used in soilless systems to provide plant support, and retain some nutrients and water. The retention of nutrients and water can be further improved through the use of sphagnum peat, vermiculite, or bark chips. These are the most commonly used materials, but other material such as rice hulls, bagasse (sugarcane refuse), sedge peat, and sawdust are used sometimes as constituents in soilless mixes.

Plastic has now become an integral part of horticultural production at various stages from nursery to marketing at consumers’ door during the last two decades. It is used at each and every stage of horticultural life cycle right from seeds packaging, nursery seedling raising, planting, propagation, mulching, irrigation, harvesting, fruit packing, preservation and marketing. The application of plastics in the agriculture sector is popularly known as Plasticulture.In 1948 Professor E.M. Emmert built the first plastic greenhouse, a wooden structure covered with cellulose acetate film. He later switched this to a more effective polyethylene film. After the introduction of plastic film to agriculture, it began being used at a larger scale around the world by the early 1950s to replace paper for mulching vegetables. By 1999 almost 30 million acres worldwide were covered in plastic mulch.

The word ‘organic’, means ‘living’, ‘earth friendly’ or ‘of plant or animal origin’. Organic farming is a very native concept of India and has been followed from ancient times. Soil is a living entity and the focus in organic farming is the soil itself. Of course, it is based on understanding the ways of nature. All organic waste from agriculture and other sources is recycled to enrich the soil. Thus, the health of the soil and its structure is maintained. The natural microorganisms of the soil are protected and nurtureed.

Organic farming is primarily aimed at cultivating the land and raising crops in such a way to keep the soil alive and in good health by use of organic wastes and other biological means of sustainable production in an ecofriendly pollution free environment.

As per the definition of the United States Department of Agriculture (USDA) study team; organic farming is a system which avoids or largely excludes the use of synthetic inputs namely fertilizers, pesticides, hormones, feed additives, etc. and to the maximum extent feasible rely upon crop rotations, crop residues, animal manures, off farm organic waste, mineral grade rock additives and biological system of nutrient mobilization and plant protection.

Orchard management is one of the important aspects in the horticulture industry. Success of orchards is mostly depends upon economic utilization of natural resources namely land, water, trees and other external inputs. All these resources have to be well utilized to the best advantage for higher production per unit area on a sustainable basis without adversely affecting the quality of the environment. Important aspects of orchard management are related with soil and water conservation, canopy management, nutrition management, weed management, plant protection measures, biotic and abiotic stress management, maturity and harvest, post harvest handling, utilization and marketing.

Soil management: Soil management aims at maintaining the fertility and productivity of soil. It creates favorable conditions for moisture supply, proper drainage and nutrient availability. It helps to maintain high fertility level and replenishment against losses, gaseous exchange, microbial activities, it helps to check soil erosion, suppress the weed population, economic utilization of interspace of main crops. Common soil management practices are cultivation, sod culture, mulching and rotation.

A cropping system refers to the type and sequence of crops grown and practices used for growing them. It is based on the available technologies of crop production. Cropping systems have been traditionally structured to maximize crop yields. Now, there is a strong need to design cropping systems, which take into consideration the emerging social, economic and ecological or environmental concerns for each ecosystem. The goal of a cropping system must be to conserve natural resources i.e. soil, water and sustain crop production. Conserving soil and water and maintaining longterm soil productivity depend largely on the management of cropping systems, which influence the magnitude of soil erosion and soil organic matter dynamics. Crop diversification is an important option in sustainable agricultural systems. Management of cropping systems implies management of tillage, crop residue, nutrients, pests, and practices for soil conservation. Difference between dry land and rainfed farming is as follows.

Major industries constituting the food processing industry are grains, sugar, edible oils, beverages and dairy products. The key sub-segments of the food processing industry in India are dairy, fruits and vegetables, poultry and meat processing, fisheries, food retail etc. Agro processing is the sunrise sector of the Indian economy in view of its large potential for growth and likely socio economic impact specifically on employment and income generation. India has the advantage of being one of the fastest growing economies in the world and it is the largest producer of several agricultural commodities. The food processing sector ranks first in terms of employment and number of factories in operation and third in terms of output.

In India, out of the total production of fruits and vegetables, nearly 76 per cent is consumed in fresh form, while wastage due to improper post harvest accounts for 20 to 35 per cent. Only around 2 percent of vegetables and 4 percent of fruit production are being processed. 

Flower is symbol of beauty and by nature attracts every human being. It is a gift of nature to humanity. Flowers symbolize the quintessence of human spirit. In India, losses are estimated to be more than 30-35%. It is due to the lack of knowledge of postharvest management of cut flowers. Several factors at pre harvest stage including genetic or inherent, climatic or environmental and management harvest factors like stage, method, time of harvesting and postharvest factors such as watering, rehydration, precooling, storage environment, packaging techniques and microorganisms influence the postharvest quality and longevity of cut flowers.

Preharvest factors

1. Genetic or inherent makeup: Postharvest lasting quality of flower species and cultivars vary considerably due to differences in their genetic make up. It is therefore desirable to grow cultivars, which possess long vaselife. 

Maturity can be defined as the attainment of a particular size or stage after which ripening takes place. It is also called physiological maturity. However,horticultural maturity is defined as the stage of development, when a plant or plant part possesses the prerequisites for utilization by consumers for a particular purpose. Mango, tomato, cucumbers, lettuce, peppers, etc. are harvested at various stages depending on the objective of disposal (horticultural maturity) prior to reaching physiological maturity, or completion of growth phase.

Maturity indices are the most important for deciding the stage of harvesting and to reduce post-harvest losses. The post harvest life of fruits are mainly controlled by maturity. Maturity signs are also called maturity standards or maturity indices. Maturity signs help in judging maturity of fruits and vegetables. There are many methods to determine maturity. The most common is the size and shape of fruit, change in colour, softening of tissues (fig, sapota), ease of detachment from the stalk (sapota, annona), shriveling of fruit stalk (watermelon), drying of nearest tendril (watermelon), days from blooming to picking maturity, sound by tapping jack and watermelon, when ripe produce hollow and dull sound on tapping but produce metallic sound if unripe etc.

India has achieved tremendous increase in horticulture production after independence. Adoption of several production technologies developed by several agricultural universities across the countries boosted the production of the horticulture sector both by increasing area under various fruit crops as well as by elevating productivity. Though the country has acquired second position in world fruit production; the productivity is less than many under developed countries.Several reasons can be attributed for declining productivity; few of them are enlisted below.

• Cultivation of old and less bearing varieties
• Improper and unscientific management of fruit crops
• Large number of old and senile orchards with declining productivity
• Problems in flowering and fruiting due to aberrant climate especially during flowering and fruiting

When fruit trees grow naturally; canopy varies greatly from species to species and cultivar to cultivar. It is mainly due to climate, planting density, rootstock, method of propagation, training, pruning, regularity of bearing, soil type, nutrition, irrigation, intercrop, growth regulators used, diseases, pests, environmental pollution etc. Plant canopy means the spread of branches and foliage of a plant.

Canopy management of the fruit tree deals with the development and maintenance of their structure in relation to the size and shape for the maximum productivity and quality. The basic concept in canopy management of a perennial tree is to make the best use of the land and climatic factors for an increased productivity in a three dimensional approach. Ideal canopy means fruit trees should have adequate number of fruiting units, it allows sufficient light and ventilation in to canopy and it should support adequate foliage and protect the fruits from sunburn. It should avoid overlapping of foliage to minimize parasitic leaves. It offers scope for effective coverage of sprays. It should avoid the buildup of microclimate, congenial for pest and diseases development. Tree vigour, light, temperature and humidity play a vital role in the production and quality of the fruits.

Fruit drop is a natural phenomenon, which occurs in most of the fruit crops. Fruit trees usually bear a large number of flowers and only a very small percentage leads to harvesting of fruits. Fruit drop occurs at various stages of maturity of fruit development. It is an adjustment of tree to its resources. Such drop is natural and beneficial to the trees and it will prevent exhaustion of the resources and breaking of branches by overbearing. The fruit drop usually takes place in definite waves or at a definite stage and those are presetting, post setting, jar drop and pre harvest drop.

The first drop i.e. presetting occurs immediately after flower opening. Usually male flowers as well as female/ hermaphrodite flowers with aborted pistil drop off at this stage.

Second drop i.e. post setting occurs a fortnight later than the first drop. This drop includes unfertilized flowers as well as some fertilized flowers drop as a result of adjustment in the trees between nutritional factors arid fruit set.

Unfruitfulness is a major problem in many fruit crops and their varieties. ‘Fruitfulness’ refers to the state, where a plant is not only capable of flowering and bearing fruit but also takes these fruits to maturity. The inability of plant to reach the fruits to maturity is known as ‘unfruitfulness’ or ‘barrenness’. In spite of adequate flowering, low fruit yields in orchards have been experienced because of low initial fruit set and subsequently higher fruit-let abscission. In an orchard, all the trees do not bear fruits equally or regularly and sometimes fail to flower and bear fruit under similar conditions, where another fruit tree bears heavily. This failure to fruit may be attributed to unfruitfulness. It is associated with internal and external factors.

Internal factors: These are as follows.

Alternate bearing or biennial bearing is a term used in fruit crops to refers to trees that have an irregular crop load from year to year. It is a major problem in some of the fruit crops. Long term studies of flower and fruit production in some of the fruit crops demonstrated that the majority of shoots on a tree bear flowers and then fruits in one year, i.e. a greater than average crop and the next year most of the shoots will produce only leaves resulting in a smaller than average crop.Thus, it is characterized by heavy crop load in trees i.e. on year, followed by a light or no subsequent crop load i.e. off year. When on and off year sequence does not follow a systematic pattern it is called periodicity of cropping or irregular bearing. Phenomenon of alternation is more prominent in the perennial fruit crops particularly Anacardiaceae (mango, Pistachionut), Carylaceae (hazelnut), Oleaceae (Olives), Rosaceae (apple, Pear, Plum, Apricot, etc.), Rutaceae (orange, tangor, satsuma, etc.) and also in tamarind, Jamun etc.

In general, plants show two distinctive phases; i.e. vegetative growth and reproductive growth. The primary objective of plant species is to reproduce themselves through the reproductive phase. However, some of the plant species do not produce viable seeds, but reproduce themselves in nature by other means. Flowering and fruiting habits vary with plant species and are governed by the kind of plant species and its growth habit, environment etc. In general, flowering and fruiting habits are known as bearing habits and it can be described by the location and type of buds, which produce flowers and fruit. The relative position of fruit with reference to its potential bud-giving rise to flower or inflorescence on the shoot is known as bearing habit. Each plant has its own bearing habit and are either terminally, laterally or adventiously Terminally means the fruit buds are formed on long or short growth, while laterally means the fruit buds are formed in the axils of present or past season’s growth. Adventiously, the fruit buds are formed at any point on the trunk. On the basis of bearing habits, fruit crops are categorised into the following eight groups

Among many factors influencing fruit bud formation, the relative proportion of carbohydrate and nitrogen in a tree appears to be the only factor that could be controlled by an orchardist. When under normal course tree does not flower; special practices such as ringing, girdling, stripping, notching, bending, water stress (with holding irrigation), root pruning and root exposure etc. are performed with the aim to control the translocation of food like carbohydrates, starch and sugars. Accumulation of food in the branches leads to fruit bud formation resulting into fruitfulness. Before performing the special horticultural practices, the orchardist should know natural growth habit of the plant, time of new vegetative growth and flowering, when it ceases to grow vegetative and mature its woods and when it takes rest

The term bio-fertilizer is related with such microorganisms that they add, conserve and mobilize the plant nutrients in the soil. Excessive use of nonrenewable exhaustive petroleum product based chemicals in horticultural production system has residual effect on soil, environment and human health. Use of biofertilizers is ecofriendly, cost effective and organic based inputs such as botanical pesticides, FYM, vermicompost, biogas slurry, disease and pest resistant varieties in cultivation of horticultural crops for safeguarding soil health and quality production.

Biofertilizers are microorganisms, which are capable of mobilizing nutrients from unavailable form to available form through biological process. They are not only cost effective but also inexpensive source of plant nutrients. They do not require non-renewable source of energy during their production. Besides, improving crop growth and quality of the product by producing plant hormones and help in sustainable crop production through maintenance of soil productivity. They are also useful as biocontrol agents, as they control many plant pathogens.

The plant growth regulators are the organic compounds other than the nutrients, which accelerate, inhibit or modify the various physiological processes in the plant system, when applied at low concentration. These growth regulators are readily absorbed and move rapidly in the tissues, when applied to the plant system and regulate its life processes in some beneficial ways to enhance the yield and improve the quality of the fruits.

The word hormone is derived from Greek, meaning set in motion. The five major phytohormones are auxins (indole-3-acetic acid and its derivatives), gibberellins, cytokinins, abscisic acid and ethylene. The key difference between plant hormones and plant growth regulators is that plant hormones are natural, while plant growth regulators are artificially synthesized and are applied to plants. Plant hormones are also called phytohormones. Plant hormones are the organic chemicals, which are synthesized by plants themselves naturally during the metabolic processes.These are synthesized at the given site and translocated to the site of action.

Vermicompost is the product of the decomposition process using various species of earthworms, to create a mixture of decomposing bedding materials and vermicast.

This process is called vermicomposting, while the rearing of worms for this purpose is called vermiculture. Vermicast is also called worm casting, worm humus, worm manure or worm faeces and are the end product of the breakdown of organic matter by earthworms. It is a mesophilic process and certain species of earthworms are used to enhance the process of organic waste conversion and produce a better end product. Vermicompost is an excellent organic fertilizer having water soluble macro as well as micronutrients, growth promoters, enzymes and soil conditioner, helpful for growth and development of plants. It helps to improve biological, chemical and physical properties of the soil.

The importance of green manuring in crop production has been known since ancient times. However, awareness towards soil enrichment is increasing in recent years, mainly due to comparatively high cost of inorganic fertilizers, increased risk of environmental pollution and need of sustainable cropping systems. Green manuring helps to improve physical, chemical and biological properties of soil and consequently crop yields. Green manuring lowers the nitrogenous fertilizer requirements for succeeding crops. However, it’s influence may vary with soil, crop environmental variables, type of green manure crop used and its management.

Green manuring is a practice of ploughing or turning into the soil un-decomposed green plant tissues for the purpose of improving physical structure as well as fertility of the soil. It is obtained in two ways; by growing green manure crops or by collecting green leaf (along with twigs) from plants grown in wastelands, field bunds and forest. Green manuring by growing the field plants usually belonging to the leguminous family and incorporated into the soil after sufficient growth. The most important green manure crops are sunnhemp, dhaincha, Pillipesara, cluster beans and Sesbania rostrata. The advantages of green manuring are as follows.

It is not just enough to produce fruit and ornamental plants in a nursery, but it is also very much important to consider the post production management practices like harvesting, packing, storage and marketing of nursery plants for successful industry.

Harvesting: Harvesting is one of the important factors considered, when nurserymen are producing seeds, bulbs, etc. The seeds or bulbs should be harvested at proper maturity stages depending on the plant species.

Seeds are generally harvested when they are fully ripe. In some of the annuals and perennials, seeds are likely to fall from the plant at ripening either due to bursting of the fruit/ capsule or due to wind. (calendula, balsam). In such cases, it is better to cover with muslin cloth or butter paper bags. Bulbs, corms and tubers are carefully dug out without injury, along with cormels or bulblets.

Packaging: The package should provide a convenient mode used for marketing and distribution. It protects the contents from undue damage during distribution. It is important that appropriate packaging should be used to preserve quality of material along with maximum survival during transit. Proper packaging of plant material (fruit plants/ ornamental plants/seeds) ensures quality during storage, distribution and transport.

Potting and repotting is an essential practice to be done in a nursery to maintain the expected vigour of the plant. When a seedling from a seedbed or plant from a flat bed or raised bed is planted in a pot, it is called potting. The same term is utilized when the bulbs of bulbous plants are planted in a pot. When a plant is transferred from one pot to another pot, it is called repotting. At the time of repotting the plants may be planted in a large pot or in the same sized pot. Repotting is necessary when

1. Plant is grown for a season or a year in the same pot and becomes pot bound resulting in extensive growth of roots in rooting media and there is very little scope for further fresh growth.
2. When a plant is overgrown and requires separation or division.
3. When soil gets depleted of its nutrients.
4. Repotting affords an opportunity to the roots to form a new root growth, as repotted soil contains sufficient amounts of nutrients and good aeration.

The young seedling stock and rooted cuttings as well as nursery plants require proper care and nourishment. The operations to be performed regularly in nurseries are as follows.

1. Shifting of plants: The nursery plants grown in the pots or polybags are to be shifted once in 2-3 months to avoid root penetration into the soil. If the taproot penetrates deep into the soil, the chances of mortality increases. Hence shifting of grafts and potted plants has to be done at the said intervals
2. Removal of rootstock sprouts: Once has to keep a constant watch on the sprouts arising on the rootstock, which are to be nipped off as and when, observed, to encourage rapid growth of scion shoots.
3. Irrigation: The young tender seedlings are exacting in their water requirement. Proper and judicious irrigation is an important indicator of a healthy nursery, which solves many problems in the nursery. There are many methods adopted in nurseries. However, it depends upon water availability, kind of nursery plants and its growth stage, etc. These methods are flow or flood irrigation, furrow irrigation, overhead irrigation through rose cans, automizers or sprinkler systems, etc.

Facilities required for propagating many plant species by seed, cuttings, or grafting and budding include two basic units namely a structure with temperature control and ample light such as a greenhouse or hot bed where seeds can be germinated or cuttings rooted. The second unit is a structure into which the young tender plants can be moved for hardening preparatory to transplanting and cold frames or lath houses are useful for this purpose.Greenhouses: There are different types of greenhouse namely low cost greenhouse and commercial greenhouses. In all polyhouses/ greenhouses means of providing air movement and air exchange is necessary to aid in controlling temperature and humidity It is best, if possible, to have in the greenhouse heating and self-opening ventilators and evaporative cooling systems. Plastic greenhouses covered with various types of plastic film have become very popular among nursery men.