eChapters

Vermicompost is the product of the decomposition process using various species of earthworms, to create a mixture of decomposing bedding materials and vermicast.

This process is called vermicomposting, while the rearing of worms for this purpose is called vermiculture. Vermicast is also called worm casting, worm humus, worm manure or worm faeces and are the end product of the breakdown of organic matter by earthworms. It is a mesophilic process and certain species of earthworms are used to enhance the process of organic waste conversion and produce a better end product. Vermicompost is an excellent organic fertilizer having water soluble macro as well as micronutrients, growth promoters, enzymes and soil conditioner, helpful for growth and development of plants. It helps to improve biological, chemical and physical properties of the soil.

4.1. Promotion of Kitchen Gardening 4.1.1. Essential Guide Lines for Kitchen Gardening • The location should be in the backyard of the house. As far as practicable, kitchen garden plot should be located near to the well, water tap or other source of irrigation. It should never be located in the shady area of home, which is generally not suitable for most of the vegetables. There should be enough of sunlight for major part of day. • It should be fenced with boundary wall or fruit crop or live fence all around. • The layout should be such as to make the garden look attractive and allow access to all its parts. The land should be laid out in small paths and plots. • The garden should preferably be rectangular in shape. • About 200 m2 area is sufficient for a five members family to supply about 1.5 kg vegetable per day

With the advent of modernization and urbanization, people are shifting from rural to urban areas, thereby, urban population is increasing day by day resulting in congested cities and towns. All around the world, a huge number of buildings are being constructed adding many more in future. Throughout the years, replacement of vegetated surfaces with paved and impervious surfaces in the urban areas have increased the temperature as compared to rural areas, because the paved surfaces absorbs, retain and reradiate more solar energy than vegetation. The ambient temperature in urban area can be as much as 6oC higher than the air in rural areas.

ABSTRACT

Vesicular arbuscular mycorrhizal (VAM) fungi are known to improve the mineral nutrient and water status of the plants even under various abiotic stresses. During present investigations VAM fungus Glomus fasciculatum was used for developing mycorrhizal association with Sesbania sesban (L.) Merrill. In general mycorrhizal (M) plants exhibited better growth and development and showed significantly higher chlorophyll content, better PS II as well as PS I activities when compared to NM plants.

In general, both M and NM plants invariably showed reduced growth and development upon exposure to drought stress. However, the M plants could confront this abiotic stress more effectively than the NM plants. This was vindicated by the faster decline in the chlorophyll content and the photochemical activities in NM plants in comparison to the M plants upon exposure to drought stress. The higher photosynthetic efficiency of the M plants under drought stress indicate the presence of certain adaptive strategies in the form of osmotic adjustment operational in these plants through VAM association. The osmotic potential of the leaf cell sap in M plants was significantly lower than that of NM plants of Sesbania sesban, when exposed to either drought stress. The lower y of M plants as compared to NM plants under drought stress could be due to the accumulation of compatible solutes such as proline and sugars. A higher level of proline accumulation in the leaves of M plants than NM plants exposed to drought stress help them to counteract the adverse effects of stress better than NM plants.

A dilute solution of acetic acid produced by a two-stage fermentation process in the first stage, fermentable sugars is converted into ethanol by the action of yeasts and in the second stage, bacteria of the genus Acetobacter oxidize the ethanol to acetic acid.

Vinegar is a liquid produced from the fermentation of ethanol in a process that yields its key ingredient, acetic acid. The acetic acid concentration ranges typically from 4 to 8 percent by volume for table vinegar (typically 5%) and higher concentrations for pickling (up to 18%). Natural vinegars also contain smaller amounts of tartaric acid, citric acid, and other acids.

INTRODUCTION

Potato (Solanum tuberosum L.) is afflicted by many kinds of viruses and their various strains belonging to different taxonomic groups (Table 1) throughout the world resultingin declinein yieldand tuber quality. Exact estimation of yield and economic losses caused by potato viruses depends on a number of factors mainly strain of the virus, variety, seasonand growingconditions etc. Generally crop losses ranges between 5 to15 per cent if all plants are secondarily infected with PVX and PVS; 15-30 per cent for 100 per cent secondary infection of PVYnand 40-70 per cent due to PLRV. Besides, in Europe and North America Potato spindle tuber viroid (PSTVd) is wellknown to reduce yieldssignificantly (16-64 per cent) dependingon the viroid strain/potato varietyand warmweather (Singh, 1988). Thesevere strains of Potato virus Y (PVY)and Potato leafroll virus (PLRV) have the potential to reduce yield up to 80 per cent, while mild viruses like Potato virus X (PVX), Potato virus S (PVS)and Potato virus M (PVM) can cause up to 30 per cent yield loss in infected plants. Atospovirus Groundnut bud necrosis virus (GBNV) causing severe stem/leaf necrosis disease in plains/plateaux of central/western India heavily infects the early crop of potato. Similarly, a whitefly transmitted begomovirus Tomato leaf curl New Delhi virus-potato (ToLCNDV) known to cause apical leafcurl disease in India, has become a serious problem in North Indian plains.

The viruses can be mechanically transmitted with plant sap, by contact and with seeds. Infectedtubers, whitefly and aphid vectors are importantfactors for the transmission of the virusesin nature. Potatoviruses are transmitted by aphids in two ways. The viruses are either non-persistent (stylet-borne) or persistent and circulative (they are ingested and persist in the aphid throughout its life cycle). The most common persistent and circulative virus affecting potatoes in India is PLRV. Common non-persistent or stylet-borne viruses are PVY, PVA, PVS and PVM. Control of circulative viruses by insecticides is highly effective, which is not the ease with stylet borneviruses. Sustainable potato production is possible only if the virus incidenceis kept under check especially in sub tropics where the weather is highlyconducive both for vectors and the common viruses. In thischapterthe major viruses and viroidof potato including symptomatology, diagnostics and their management have been discussed.

Plant viruses, like all other viruses, are obligate intracellular parasites that do not have the molecular machinery to replicate without the host. The plant viruses are defined as viruses pathogenic to higher plants. The discovery of plant viruses causing disease is accredited to Beijerinck who determined in 1898 that the plant sap obtained from tobacco leaves with the mosaic disease remained infectious even after passing through a filter. This was in contrast to bacteria, which were retained by the filter. Beijerinck referred to the infectious filtrate as a contagium vivum fluidum, thus, he used modern term virus.

Viruses occasionally cause significant problems in vegetable crops. However, the prevalence and severity of viral diseases differ from year to year. Aphids spread many of the viral diseases observed in vegetables. There are two types of viral transmission by aphids, i.e., persistent and non-persistent transmission. It is important to understand the difference between these two because persistent and non-persistent viruses differ both in their uptake and behaviour within the insect vector, consiquently, tactics used to limit their and spread vary considerably. In persistent transmission, the aphid usually carries the virus for life. Uptake of virus requires extended feeding and after an incubation period of several hours or days, the virus replicates and circulates within the insect. Because of the time required for feeding before acquisition by an insect vector, the spread of persistent virus is favoured by colonizing aphid species that spend time in the crop. Controlling the aphid vectors with insecticides can reduce the spread of persistent plant virus significantly. In contrast, aphids can acquire non-persistent viruses (NPV) within a few seconds after sampling an infected plant. Winged migratory aphids can move quickly from infected plants onto healthy ones, transmitting the virus in the process. Aphids rapidly lose the virus particles from their mouthparts, which are cleaned when they feed on the next available plant and are unable to transmit disease to additional plants. Because of the speed in which aphids acquire and transmit non-persistent viruses, insecticides are not usually effective in controlling their spread. One of the most common viruses found in many vegetable crops is cucumber mosaic virus (CMV). This is transmitted by several aphid species in a non-persistent manner. There are several strains of CMV that can infect over 775 different plant species in 85 families including snap bean, peppers, tomato, lettuce, tobacco and sugar beets. Symptoms vary depending upon the plant species infected but range may be from yellow-green mottling on leaves and fruits to severe stunting of plants. The viral diseases affecting different vegetable crops are being discussed below:

Visit to a seed processing unit and attending the following questionnaire to know firsthand information on operations of shop floor

NAME OF THE UNIT: 

    1.    Location of Seed Storage 
    2.    Date of Inspections/visit

Controlled environment agriculture (CEA) refers to methods of cultivating crops in managed environments to optimize resources and increase productivity. CEA systems regulate both the aerial and root environments, ensuring that plants stay within their ideal growth conditions. One popular method within CEA is indoor hydroponic farming, where crops, including fruits and vegetables, are grown without soil.
CEA includes various levels of technology integration to achieve optimal
plant growth, including:
• Low-level Integration: Basic environmental control in open-field production, such as shading and irrigation systems.
• Passive Environmental Controls: Systems for soil-based crop production, such as covering materials and high tunnel structures. • Integrated Sensors and Active Control Systems: Used in greenhouse systems to regulate environmental factors and enhance sunlight.
• Full Indoor Production: The most advanced method, where technology is used to create an ideal environment for plants independent of external conditions.
HYDROPONIC SYSTEMS
In hydroponic systems, plants are either grown with their roots in direct contact with liquid nutrient solutions (often supported by floating rafts or trays) or placed in containers with other types of soilless media like coconut coir, rockwool, or peat mixes. Irrigation delivers all necessary nutrients in these soilless systems. Advantages and Disadvantages
Hydroponic systems offer several benefits, including:
• Year-Round Production: Crops can be grown continuously, even during winter months.

California’s Napa Valley, situated at the northern end of the San Francisco Bay 30 miles (48 kilometers [km]) from the Pacific Ocean, is the most famous wine appellation in the United States. This small valley, 56 km long and 8 km wide at its broadest point, has produced some of North America’s finest wine grapes from the 1850s to the present. Today it contains approximately 18,616 hectares [ha] of vineyards along the valley floor, in the foothills and mountains flanking the main valley and in the smaller valleys in the eastern part of Napa County [45].

Introduction

A variety of glassware, plasticware, and other apparatus are used for experimental purposes in a laboratory. They need to be washed, cleaned, dried, and sometimes sterilized before they can be used in the next set of experiments. Glassware needs special care of handling during washing, drying, sterilization, etc. because even a minor mistake in handling of glassware may result in its cracking/breakage and it may become unserviceable. All of these may result in a delay in experimentation if spare piece of the glassware is not available or it may affect serviceability of the associated apparatus.

A large number of glassware such as beaker, flask, measuring cylinder, burette, test tube, etc. are regularly used in a laboratory, which requires careful handling during the different stages of experiment as well as after completion of the experiment while preparing them for another set of experimentation.

Glass being a complex silicate, its properties depends on the type of silicate anions in the structure and the cations formed. Thermal properties of glass changes by the addition of boron oxide (B2 O3 ); hence, borosilicate glass is extensively used in the laboratories. With this brief background information, let us discuss about the necessity, procedures, and precautions during washing, cleaning, drying and sterilization of laboratory-wares. Figure 3.1 shows various advantages of using borosilicate glass in a laboratory.

Good laboratory practices require clean glassware, because an experiment may give erroneous result if dirty glassware is used at any step of the experiment. Hence, the glassware must be physically and chemically clean; and in many cases, it must be microbiologically clean or sterile. The commonly used glassware in a laboratory include test tube, measuring cylinder, pipettes, beakers, flasks, microscopic slides, etc.

26.1 INTRODUCTION

India is the second largest producer of fruits and vegetables and ranks next to Brazil and China, respectively. With the commensurate total production of 63.5 and 87.2 million tonnes of fruits and vegetables, the country shares about 11 per cent of total production under fruits and 13 per cent of total production under vegetables, respectively (Anon., 2008) in global scenario. Horticultural produce undergoes spoilage at the time of harvesting, handling, storage, marketing and processing resulting in huge wastage. Efficient management of this waste can help preserving essential nutrients of our food and feeds and bringing down the production cost of processed product, besides minimizing pollution hazards and purifying the environmental condition. Recycling of horticultural waste is one of the most important aspects of utilizing it in a number of new ways to yield new products and meeting the requirements of essential products required to mankind.

In advance countries like USA, Australia, Brazil and Israel, more than 50 per cent of fruits and vegetables productions are processed into different products, whereas, in India it is less than 2.0 per cent of total production. Generally, post harvest losses in fruits and vegetables range between 25-30 per cent of total production, valued at more than 57,000 crores annually due to lack of availability of appropriate post harvest infrastructure (Guleria and Verma, 2008). Horticultural crops are grown all over the country incurring wastes everywhere. There are different stages of waste from farm to fork.

Introduction

Food processing is an important sector in agriculture, the scope of which has increased manifold that can help to prevent wastage of perishable commodities to a great extent. But, at the same time, the food processing industries generate a large quantity and variety of food products, provide employment to a large number of people and uplift their economic status. The production, processing and preparation of food, all results in generation of huge quantity of waste material causing health hazards due to environmental pollution. The waste material may be in the form of leaf/ straw, waste during harvesting, food preparation waste, after processing waste, unused material as waste, food processing operation waste, etc. The huge wastage of the food material is due to lack of control on such agri-economy practices. So, the disposal of waste material has become a challenge to the processors, as different agencies are pressurizing for an environment friendly treatment of waste material. The utilization of waste for the production of value added products is very important in the management of food processing waste.

Agriculture is biggest user of water, accounting 70% of all withdrawals. It is major water-consuming sector due to intensification of agriculture (CWC, 2021). With changing climatic condition, demand of water will increase. Hence, conservation and efficient management of limited water has become the need of the hour for sustainable fruit production. Since per unit returns from horticultural crops are higher, their production system improves the net return of farmers and would impart resilience to aberrant weather (Meghwal et al., 2018). Therefore, immense opportunities for quality production of water-economizing horticultural crops. In arid and semi-arid regions, uncertain, erratic and scanty’ rains coupled with meagre irrigation facilities leads to low and unstable yields.

In the present scenario of rapidly increasing population and decreasing cultivable land, there is urgent need to increase the agricultural productivity. According to Indian Council of Agricultural Research (ICAR), 280 million tones food grain would be required to match the country’s demand by 2020. It will be a difficult task to meet this food requirement in near future from the present productivity levels. It is necessary to increase agricultural productivity, because about 60% of Indian agriculture is rainfed. Proper use of even a single drop of rain water is necessary to ensure the success of rainfed agriculture. In hills, agriculture is main source of livelihood of rural people. However, small and scattered land holding, difficult topography, womendependent agriculture, totally rainfed, typical socio-economic factors and migration of youth towards urban/plain areas are major constraints of hill horticulture.

In the high altitude areas, the river flow in deep valley at the toe of slopes rarely serve any purpose as far as domestic water supply and irrigation are concerned and hence, agriculture in these areas is mostly rainfed. However, these areas received high magnitude of rainfall but this rainwater is not possible to convert into soil moisture due to steep terrain of hills which provided minimum opportunity time for infiltration of rainwater. It has been estimated that only less than 15 per cent of the rainwater is able to percolate down through slopes and recharge the soil moisture. The rainfall pattern hill is erratic i.e. most of rain (approximately 70% of annual rain) received only during the two months of monsoon. Furthermore, the climate of high altitudes comprises several climatic anomalies such as wide variability in temperature (-3 ^oC to 35 ^oC), frequent snowfall, hail, sleet and erratic pattern of rainfall. Under such abrupt conditions crops grown in open conditions could not be sustained.

Principle: To determine water in soluble solids, a known quantity of sample is boiled in water and the insoluble material is collected on a weighed filter paper. The insoluble mass is then washed with hot water and dried in oven.

Relationship Between Plant and Water

Water is the most vital component of the living cells and the basis of plant feeding. Water is also characterized with extraordinary physical properties: it has high specific heat, biggest latent heat of vaporization, very high thermal conductivity and greatest surface tension. Large amounts of heat are tied up with water because of very high specific heat, which contribute to both climatic stability and to heat budgets of the plants and other organisms. Water molecules are integral part of living systems being the solvent for metabolites and structural component of proteins and nucleic acids. In fact, biological macro-molecules cannot exist in their complicated secondary folding or spiralled helixes without the support of hydrogen bonding within their water matrix. The water matrix is also critical for metabolic activity because its properties of hydration permit ready reactivity between molecules in solution as well as between enzymes and their substrates, and the biochemical processes are sensitive to tissue hydration. A reduction of only 20-25 per cent below maximum hydration is sufficient to cause metabolic malfunctioning of many enzymes. It is the substrate for photosynthesis and a product of respiration. Water also helps to buffer plant tissue against fluctuations in the external environment. Plant growth including leaf expansion, organ enlargement, reproductive development and stomata function are all clearly associated with moisture status. Hormonal changes (abscisic acid and cytokinins) in plant body occur with brief reduction in water potential. Water is the also major force in shaping the climatic patterns.

Water is a critical input for crop production. Its optimum availability is important in augmenting and sustaining crop productivity. Lack of adequate supply of water can limit crop yields ranging from 10 to 90% or even be subjected to mortality if moisture go below permanent wilting point. It is also observed that the moisture shortage during some critical crop growth stages would cause severe detrimental effect. This necessitates us to provide irrigation to crops at right quantity and frequency. In other words, irrigation schedule plays key role in optimizing or maximizing crop yield. Moreover, judicious use of irrigation water has potential to enhance the agricultural productivity which in turn would lead to food security. As water resources are getting diminished day by day, the application of water saving techniques would be needed for addressing the food security objectives of the nation.

Irrigation is one facet of the inputs which need to be carefully managed so that profits are maximized. Irrigation plays a major role in any agriculture crop production. One should be aware of different types of irrigation adapted in orchards or crop cultivation to become a successful grower. Irrigation is very important component of crop cultivation as sufficient moisture must be maintained in the soil for obtaining the optimum growth and good quality yield. The aim of irrigating a plant should be to wet the entire root zone without allowing any wastage of water beyond the root zone. The irrigation systems have to be properly devised so that the water requirements of the trees are met at the minimum expenditure without any wastage of water. Irrigation practices can be improved if a range of important factors like crop type, crop water requirements, climatic conditions, soil type, water quality, method of irrigation are taken into account.

Crop type

The type of horticultural crops grown influences irrigation practices. Annual vegetable and melon crops have high water requirement, hence irrigation management is extremely critical to their productivity during their relatively short life span (10-20 weeks). Perennial fruit crops tend to require less water and management, although critical, is not generally as critical as for annual crops.